what's going on everybody :) lol

You mention other videos, I saw them to which led me here. Even though I saw a few before yours, I still liked your a lot. What the other ones are missing are the details and the thinking out loud problem solving and ideas you have here. Nice job, very helpful.

That's why I like this channel you get everything from cars to comedy to DIY. That is one cool idea I will be doing that

@HonestlyOCD

5 жыл бұрын

Appreciate the support 🙌🏼🙌🏼

I too have gotten the valves and the pump but not yet installed. I have more confidence doing the install having watched this video. Thanks.

Neat. I was surprised when I went searching to buy one and mostly just found DIY.

Foam nation is the greatest addiction. The greatest!!

Would be cautious with rubber valve stems the pressure could deform the plastic shooting that stem out. Would personally use valve stems that have a mechanical fastener to further reinforce the interface. Good video and idea brother👍.

I've been doing this for years but I use my air compressor to fill it up. I like the idea of attaching a portable rechargeable pump. On a 2 gallon sprayer I may need to refill it 2-3 times. That's not a big deal when I'm at home.

@codhruv839

2 жыл бұрын

what bit did you use?

@travisr4970

2 жыл бұрын

@@codhruv839 Unfortunately, I don't remember.

im gunna use this to clean my bathroom and car. good stuff.

This thing is awesome, gonna try it out. I have to spray algae at high places and pumping for about 20-25 tanks of this kills the shoulders.

I’m going to try it, thanks 👍

You could implement some wearable gear [like a backpack?] to provide the pump a measure of protection from water and to facilitate its relative proximity to the sprayer. Remove the pump's hose and either replace it [and it fitting(s)] with an appropriate length hose [i.e., backpack-to-sprayer length chosen for comfort] or simply add a length of hose between the sprayer and the existing hose [thus preserving the fitting at the end].

Very cool bro.... thanks for the idea.

Look into a single paintball pod holder, it should hold that pump and be able to velcro around the whole thing

I was thinking about doing the same thing!

Depending on the width of the of the e-pump, an adhesive broom holder might work

This is very interesting. What spray tip do you all recommend to switch out on the end of a general lowes 2 gallon pump sprayer that will extend the range of the spray and also be sturdy?

Ryobi makes a pump that uses their 18V One battery that I am planning on trying with my backpack sprayer. Not sure if it will work but not much of a downside.

Did the rubber stem continue to work without issue? Or would you recommend one that uses a screw system? Im wondering if i should send it on drilling a hole in my IK Multi Pro 2.

What size drill hole do you use?

@clybrokeagaincausemonareve9753

5 ай бұрын

For the .453 rim hole valve, use a 29/64ths drill bit.

Great video How u know how much psi to put? I have 2/3/5 liter how much to put each? Thanks

What brand is that bike pump? How long does it take to charge and how much?. Also a suggestion, use a metal valve stem instead of this rubber one. It is more sturdy.

Very good

I added an metal automotive valve stem to all my pump sprayers for 10 years and just air them up like a tire. Can't remember the last time I used the hand pump.

Poke a small hole, on the husqvarna one, pull out the black rubber hose, and poke a hole in the plastic black hose connected to it, the hold has to be 1 inch from where you screw the fitting on, then, get some scotch brite pads, cut em up and put them on the tip of the husqvarna garden sprayer and use foaming soap, works just as good as the IK 9 or 12

@richardfox3924

2 жыл бұрын

Have same pump could possible link video on KZread describe were punch tha small hole?

@bmxbandito666

2 жыл бұрын

@@richardfox3924 punch a small hole exactly 1 inch from the base of where the pick up tube screws on, like pull the whole tube out, poke it with a needle or push pin and then re insert the tube and fill it with foaming soap

What size drill bit?

@chebrneck

Жыл бұрын

29/64

I suggest using a retractable cargo net to hold the air charger in. =)

@joegormanly

2 жыл бұрын

brent i use heavy duty hook and loop velcro it has been well over a year in use. and never comes of

@richardfox3924

2 жыл бұрын

@@joegormanly have link similar prouct u mention?

Man,I can use this for window tinting cars.I might have to get a longer air hose for it

Which bit did you use? Was that a 11/16?

@clybrokeagaincausemonareve9753

5 ай бұрын

For the .453 rim hole valve, use a 29/64ths drill bit.

Try this with the IK9.

Came for the sprayer left with the pump.

Nice body. Taht. Mod. Price 80$. In amazon. Eletric spray. Thx man for sharing.

I will mod it when i got my tire valve

I love my solo sprayer I have the one you have and the bigger one

@HonestlyOCD

5 жыл бұрын

Nice!! It’s a good setup 💪🏼

Genius idea! lol #teamnopump

@HonestlyOCD

5 жыл бұрын

🙌🏼🙌🏼

What size drill did u use for it

@clybrokeagaincausemonareve9753

5 ай бұрын

For the .453 rim hole valve, use a 29/64ths drill bit.

I purchased a battery-operated garden sprayer.

I rikey this!!!

First??🤔 Also don’t even own anything you showed but still going to watch lol

@HonestlyOCD

5 жыл бұрын

Haha thanks!

I bet that pressure relief with pop when hits it’s limit 40-60 max? Need a gauge cap top if don’t need pump. The failure point will be pump before high pressure. I thought red thing was pressure safety relief in case someone puts organic sod fuel in there pumps it to dangerous pressure. What’s cap size threading for tiny one and female threaded ones looks like if cut top off neck could screw on a lid, put gauge safety at top more volume, they sell pressure pump tanks no? Someone’s building vacuum or pressure vessel ran chamber. PVC tank DIY can withstand insane pressure.

How did this hold up OCD?

So much sexual innuendo in this vid haha

@HonestlyOCD

5 жыл бұрын

Yeah I laughed a lot while editing lol

drill bit size please

What's going on OCD

@HonestlyOCD

5 жыл бұрын

Just missing my workplaydrive lol

Still no replie to the size of the hole.......

@HonestlyOCD

4 жыл бұрын

Nope no replies at all lol I honestly don’t remember the exact size I held it next to the stem and eye balled it 🤷🏻‍♂️

@antoniobullard9072

3 жыл бұрын

Hello, where did you get the gray pump up sprayer from that is on the other table

@antoniobullard9072

3 жыл бұрын

By the way I just bought the portable bicycle pump from Amazon

@clybrokeagaincausemonareve9753

5 ай бұрын

For the .453 rim hole valve, use a 29/64ths drill bit.

How much pressure can it withstand?

Nice video brotha this is @vthandi on Instagram

So you are putting a PUMP on a PUMP SPRAYER. And you are now needing to carry ANOTHER object around. I don’t get it. I bought the Solo 418 for the convenience of the hand pump and its efficiency.

@HonestlyOCD

2 ай бұрын

it's not for everyone but I am happy you are enjoying your sprayer!

JEEPERS…..5 people asked you what drill bit….no answer….

@HonestlyOCD

Жыл бұрын

jeepers creepers lol this video is three years old lol I get hundreds of comments per week on every video from my old ones to my newest so comments can and do go unseen it's not easy when this is just a small hobby for me lol the drill bit size honestly depends on the side of the valve stem you have .. I've never met a person that had just ONE drill bit .. more often than not a person will have a drill bit set .. if someone can't judge enough what size drill bit they should be using in relation to the size of the stem than I personally think that they shouldn't be owning or using a drill bit because it's likely an unsafe situation lol have a great day!

@catbirdfeeder

Жыл бұрын

@@HonestlyOCD ….well I guess I heard that! …..

@clybrokeagaincausemonareve9753

5 ай бұрын

For the .453 rim hole valve, use a 29/64ths drill bit.