Thank you sir. You video helped me a lot.❤❤

Thank you so very much

Perfect

Thanks

@kayindironaldferguson6652

3 жыл бұрын

Types of joining with glue

what kind of cement will use joined rubber to drum pulley?

Nice

Super

can u tell me what type of adhesive use for bonding between roller and NBR based rubber compound?

I have 14 years in this work

Good what did you apply for covering the rubber does it need vaccination ?

Always overlap your lagging. Bevel the lower layer, over top layer and then grind Down.

Creo que para el Forrado del tambor hay otra opción que es solapado que también queda ien

@MrFernandoBedoya

Жыл бұрын

cómo es?

@bayronsotoherrera4251

Жыл бұрын

Montando una punta unos 2 o 3 centímetros encima de la otra, pero antes hay que hacer un desbaste a la primera punta los centímetros a montar

@MrFernandoBedoya

Жыл бұрын

@@bayronsotoherrera4251 Gracias. Tiene sentido.

what is the title of your job?

how to calculate diamond grooves in roll 90 inches rubber face,16 inches diameter

@eduardomachado7788

Жыл бұрын

Medir o diâmetro do rolo e multiplicar por 3.14

Hola me entereza saber el proceso de pegado puede dar traducido en español por favor se lo agradezco

@jorgeancira2989

3 жыл бұрын

Yo te puedo ayudar de dónde eres

@alejandroferle4918

2 жыл бұрын

@@jorgeancira2989 Puedo consultarte los pasos para el correcto pegado, soy de Argentina

@jorgeancira2989

2 жыл бұрын

@@alejandroferle4918 claro que sí , bandasanciraleon@hotmail.com

only one coat of cold cure ?

What method is used to work out how much rubber is needed to cover the pulley (roller) Thanks

@dragway3513

3 жыл бұрын

I always use the following "formula" : (Pi * Diameter) - (2/3 of the diameter/width of the material I use for welding the seam)

@merrickaaron

2 жыл бұрын

Pulley diameter x 3.14, + rubber thickness eg. 12mm rubber, (3.14 x dia) + 12 = req ^length^. Face width x length = amount needed to cover.

Why wouldn't you just do a long pre-bevel one end then stitch your lagging up the bevel? Only time I do a but to but edge is strip lagging.

@Justvulc

2 жыл бұрын

We do it with proven technology!

@derekleblanc571

2 жыл бұрын

Doesn't matter so long as it works. but if your not perfect with your mesurements and calculations you might have a gap or be forced to try to shrink the lagging wich will often cause a section with air bubble /( unbonded lagging to pulley) Easier and safer to ride a few inches of rubber over a gradual bevel then cut and buff the extra. But if you can line it but to put perfectly then awesome good job! Do you seal the but seam ? Of so what do you use?

@alex86902

Жыл бұрын

@@derekleblanc571 Hi Derek, We use a similar method to do our drums. We lay the rubber to a 15mm overlap from our measurement to allow for mistakes, once glued and stuck up to the last edge we will take a mark and trim the edge to within a 2-3mm overlap using a small shim on the underside to prevent premature sticking, we then lay the rubber in and stitch away any bubbles while the glue is tacky. We do this method to allow for multi directional travel and if it is in a harsh environment will seal it with a 2 part rubber mixture. I can say from our experience over the last 10 years failure due to the butt join of the lagging has not once been an issue. I do enjoy seeing other methods so of you have any tips id be glad to hear them.

@derekleblanc571

Жыл бұрын

@@alex86902 interesting technique kind of the best of both worlds. I like it. And that 2 part rubber mixture is probably the tire repair compound wich works awesome. Thankyou for the share.

Ojo con el uso de los epp's

That's my speciality work

Jo gum laga raha us gamka name kiya Bhai

That is cold solution

Eine Tip Top Stahl Gummierung SC 2000

What is the solution apply after roller grinding??

@Justvulc

4 жыл бұрын

use metal primer

@livebihar1718

3 жыл бұрын

Watt this sulation

@marvinsoriano5611

2 жыл бұрын

none only water to clean up

@kaushikkumar8256

2 жыл бұрын

Chemlock

Plz give names all solutions which you applied

@Justvulc

4 жыл бұрын

Hello! Adhesive TRS 2002 new justplatform.com/en/catalog/chemical-products/trs2002.html TRS METAL PRIMER justplatform.com/en/catalog/chemical-products/trs-primer.html Solvent Just-Bond MEK justplatform.com/en/catalog/chemical-products/trs-solvent.html Pulley lagging JUST-Grip justplatform.com/en/catalog/pulley-lagging/pulley-lagging-just-grip.html Tools: justplatform.com/en/catalog/tools.html

@herdeirosdeantoniojoaquimc9063

3 жыл бұрын

@@Justvulc telaprefurada T569 I 6telaprefurada

What the type using glue.,,?

@Justvulc

3 жыл бұрын

TRS 2002 NEW processed with HARDENER TRS 1000M is a tetracloroethylene cold bonding solution with excellent adhesion and superior dynamic load universally applicable for durable rubber-rubber, rubber-fabric, rubber-metal and fabric-fabric bonds in the fields of wear protection as well as in conveyor belt systems. justplatform.com/en/catalog/chemical-products/trs2002.html

Qual o contato fone

@Justvulc

3 жыл бұрын

justplatform.com/es/contacts.html

Phục vụ cho các em học tập tại

Много ошибок!!!

Полный бред

Fuck steel toed shoes. lol

Mdr c est pas comme sa con fait c est pas un bon colleur