Just a short video where I prepare the E50 Supermaxi Engine for a Gilardoni 74cc cylinder.
Жүктеу.....
Пікірлер: 11
@smh3395 ай бұрын
Alright nice job! Ok now lets make a 80cc, lets use this race case ADDY 50-1 A E50 4-bearing reed valve case, with lots of room for improvement. Also gonna need a custom forged piston, we can forge that in our garage like Burt Munro, may take a few try's but we can do it, then straight cut gears and off to the races! Alrighty then let's get on it and do a 💯
@TheGreasemonkey872 жыл бұрын
Nice job! Can a drill press be set up for millling a crankcase?
@fiftynineridge
2 жыл бұрын
Probably yes, there must be some sort of rigidity in the setup of course but the material is soft so if you go slow with small increased steps it should work.
@pascalrieder92164 жыл бұрын
the problem with the supermaxi is that its a 3 bearing, it wont hold the 74cc for long.
@fiftynineridge
4 жыл бұрын
That’s true, and that is why I made a 4 bearing conversion in this other video kzread.info/dash/bejne/aqKr1sekZLLUqc4.html
@andrerosenquist53274 ай бұрын
Nice job! What is the name of the drill you use? :)
@fiftynineridge
4 ай бұрын
Thnx, the tool is called ”boring head” or ”ursvarvningsverktyg” and it’s used for making accurate holes.
@andrerosenquist5327
4 ай бұрын
@@fiftynineridge tak :)
@havardjohansen66803 жыл бұрын
Pipe are u going too use? Or do u make ur own calc
@fiftynineridge
3 жыл бұрын
I make my own cause every porting needs that in order to work properly
@havardjohansen6680
3 жыл бұрын
Thats Nice.. make my own pipes too. But never too the gilardoni, going too make my a gilardoni engine now
Пікірлер: 11
Alright nice job! Ok now lets make a 80cc, lets use this race case ADDY 50-1 A E50 4-bearing reed valve case, with lots of room for improvement. Also gonna need a custom forged piston, we can forge that in our garage like Burt Munro, may take a few try's but we can do it, then straight cut gears and off to the races! Alrighty then let's get on it and do a 💯
Nice job! Can a drill press be set up for millling a crankcase?
@fiftynineridge
2 жыл бұрын
Probably yes, there must be some sort of rigidity in the setup of course but the material is soft so if you go slow with small increased steps it should work.
the problem with the supermaxi is that its a 3 bearing, it wont hold the 74cc for long.
@fiftynineridge
4 жыл бұрын
That’s true, and that is why I made a 4 bearing conversion in this other video kzread.info/dash/bejne/aqKr1sekZLLUqc4.html
Nice job! What is the name of the drill you use? :)
@fiftynineridge
4 ай бұрын
Thnx, the tool is called ”boring head” or ”ursvarvningsverktyg” and it’s used for making accurate holes.
@andrerosenquist5327
4 ай бұрын
@@fiftynineridge tak :)
Pipe are u going too use? Or do u make ur own calc
@fiftynineridge
3 жыл бұрын
I make my own cause every porting needs that in order to work properly
@havardjohansen6680
3 жыл бұрын
Thats Nice.. make my own pipes too. But never too the gilardoni, going too make my a gilardoni engine now