❤ love the music with it. Made it so easy to watch

Beautiful porting. I did mine today after seeing this video, it's not so tidy, but have another 4 engines to practice the art on.

Thanks for the info.I really enjoy your videos.

What a superb video. Nice work.

Very wel done, ancwered lots of questions. And was abe to show 'helpers' how to assist me. :-)

Great video for an old good italian engine.

great reference vid, love me some 77. A little trick when case matching... Instead of using a marker, cover the face with blue painters tape, then with your gasket and exacto, cut out the tape where you are removing material. It makes a much sharper line, and when your bit hits the tape, it will fluff up a little and you can clearly see you are at your edge.

This is pure art

This is a good video!

Looks good! :)

clean work. i go way bigger on those!

Спасибо! Очень хорошее видео!

@pacetanner We will be doing more in the future. Motobecane is on the list! Thanks for the support!

Sure do. Check out our WSL pipe, and some of the kits we offer.

I think the direction of the seal on the main gear is wrong. the green side should be on the outside, sealing it off and keeping the dirt out. I never saw one puch maxi moped with the seal on the main gear installed in the way this video shows. And doesn't the brass spacers get stuck due to the heat? That's so far the only notice. I believe the rest is all done in the correct way.

@piperfect

7 жыл бұрын

No. That is how they come from the factory. .......but these are dual spring seals so it shouldn't matter. I put 8 of those brass spacers on and it did get stuck, I got it off with a rubber mallet. The MLM SPACE SAVER studs are awesome on a Polini but they are too wide for a Gila :).

bel lavoro !! ai miei tempi solo modifiche sui pezzi originali....aparte gli ultimi periodi dal 1983 in avanti che sono arrivati i Malossi 65cc ;-)

got any great videos on tuning the m48 as used in the ariel 3 and batavus bikes?

I used porting wax for my carbide cutters keep them clean you don't lose your indication mark like W40 can wash it away.... WD40 on the stones keeps them clean

cool video I am building an av7 any chance you guys will be doing a video of one of these? ps i got my kit from you!

@ECSuspect Great tip!

@1977mopeds I use same method to fit main bearings but the pro's say to use a device to push them on. also its good to match the transfer part of cases so that they line up with crank webs so that there is a smooth passage if that makes sense?

nice

@maxmojo2 ops.. ha-hem :-) Gilardoni makes only cylinders .. Btw, i like this old 2 strokes engines, even if is austrian ahah and the international passion for mechanic and music.

how do you close that hole you make in the port of the case?

@wildwespocketbike They are on order with Italkit. Just waiting for them to come in. Dan

how did you "flat out" the weldings?

from where you have these bushes on the stud

Hey dudes,I just subscribed. Im a collector and just bought two 1982 honda urban express deluxe nu50m.you got after market parts for those?

What clutch is tht? Would you recommend tht clutch on a 70cc kstar build e50?

No polishing?? Still seems rough. Missing the first startup in the vid!? :-(

Hi there... I have a puch maxi and the bearings just failed so I'm hopefully am going to rebuild the motor... How much money (dollars) is it to get new seals and bearings for the whole e50 motor

reeed valve but only 4 transfers, why not have boost ports above reed valve? and the tiny holes in the piston to feed crank case, could be bigger or cut a slot down cylinder? Interesting little engine though.

is there any chanse on doing a tomos a35 engine?

Schönes Video aber paar Fehler und fragwürdige Entscheidungen beim Zusammenbau... PS.: viel Glück mit der Kurbelwelle bei dem Zylinder xD

plz do this on Kreidler engines, much more HP with SB cilinders

?? is the cylinderhead turnd 90 degre ??

now start doing this kind of videos with all kinds of zündapp and kreidler engines!

i wanted you guys to do the welding and bore i was not going to send my case to someone that not answser

Is porting necessary? Or no

When i were you i shouldn't polish the portings. When you don't you'll get a better flow

Then what should you use?

what happens if I don't grind the case?

is it necessary to weld the case @1977mopeds?

@mopedicon

10 жыл бұрын

If you are installing a Gila, or a Metrakit, yes.

@carljohanalsing

10 жыл бұрын

Ok, thanks for the info!

@4estfloor

9 жыл бұрын

Do you add material to the case? I thought gila e50s needed material added?

eu precisava da fiacao

think this will work on a jawa 207

Leave a message, and we will give you call back. Thanks!

@TheOriginalJapandrew

5 жыл бұрын

More info on welding the case? Materials etc.

@nicodanger13 AUSTRIAN* Engine.

how much does this cost?

@nathanw5747

13 күн бұрын

230 for the kit about 100 $ to bore and welding cases without shipping to and from. Likely 450ish.

I am not sure if we got the message. Call 1.888.743.1977, I would love to hear from you.

i got your email i call but no answer:0(

This ist tuning and nothing else

This video missed the most needed to be seen step of boring the case to fit the wider jug.

@piperfect

7 жыл бұрын

Mike S ....a flap wheel dremel or drill bit works well.

This video changed my life 😳 delete that meaningless crap

Your seal ring in the back is in the rong way

@louisr1873

5 жыл бұрын

No in the manual picture it is mounted this way

Why😰😭😂

2 Strokes -- Yes. Mopeds -- No.

when will you have the gila kits back in stock????? ive been waiting?????? wes from vegas