In this video I describe the basic process how to use CHIRP to program radio frequencies into the Baofeng BF888S radio. theoilykrafter.com/shop/ols/c...
Жүктеу.....
Пікірлер: 19
@shasashu7 күн бұрын
Thanks Uncle.
@theoilykrafter
6 күн бұрын
You are welcome.
@yvesseydou9649 ай бұрын
Thank you; good tutorial
@theoilykrafter
7 ай бұрын
Thank you.
@TerrellBrown-dh6dm7 ай бұрын
Great. Thanks
@theoilykrafter
7 ай бұрын
You are welcome!
@Meister_J7 ай бұрын
Thank you, this was great. How would I program the same radio to work with other brands like SFE, Panasonic? I recently had to replace my radio but I'm struggling with the setup
@theoilykrafter
7 ай бұрын
You will either need software to program your radios or become proficient at programming them from the front panel. Here is a link to check and see if your radio is supported by Chirp. chirp.danplanet.com/projects/chirp/wiki/Home
@Meister_J
7 ай бұрын
@theoilykrafter Thank you. My Baofeng 888s is supported but the SFE S780H RADIO is not support. So I can't configure them. I tried contacting SFE
@edenc9275Ай бұрын
This is a great video and exactly to the point, however I'm still unclear why I would be doing this. Is it to make sure that all my BF888s radios share the same frequencies for each channel? And you replaced the settings with an existing file; where did you get that file?
@theoilykrafter
20 күн бұрын
I used Chirp to create the program that was written to the radio. After programming the first radio. I read from the next radio and copy and pasted the frequency table into the tab that I just read from the radio after saving the original configuration. Then after pasting would save and write to each subsequent radio to ensure that they all have the exact same program.
@miguelesteves97404 ай бұрын
The software won't allow to change the language like some others do. That would be helpful as well
@theoilykrafter
4 ай бұрын
I am not sure that I understand the question. Are you referring to the language setting in Chirp ?
@ThePolishKid12 күн бұрын
My CHIRP program says that there is "No response from radio" after clicking "OK" to "communicate" with it. Do you mind telling me how can I fix that?
@theoilykrafter
6 күн бұрын
There are a number of things it could be. A bad programming cable, an in correct baud rate on the COM port, an incorrect data bits and stop bit setting. It could also be that you have the wrong model radio selected or a radio that is not supported by Chirp.
@LeePyatt3 ай бұрын
great tutorial. fails for me with no response from radio
@theoilykrafter
3 ай бұрын
Thank you. Sorry to hear that you haven't had success with responses to your attempt.
@LeePyatt
3 ай бұрын
@@theoilykrafter i finally had success. required turning it on counting 2-4 mississippi and hitting the ok button.
Пікірлер: 19
Thanks Uncle.
@theoilykrafter
6 күн бұрын
You are welcome.
Thank you; good tutorial
@theoilykrafter
7 ай бұрын
Thank you.
Great. Thanks
@theoilykrafter
7 ай бұрын
You are welcome!
Thank you, this was great. How would I program the same radio to work with other brands like SFE, Panasonic? I recently had to replace my radio but I'm struggling with the setup
@theoilykrafter
7 ай бұрын
You will either need software to program your radios or become proficient at programming them from the front panel. Here is a link to check and see if your radio is supported by Chirp. chirp.danplanet.com/projects/chirp/wiki/Home
@Meister_J
7 ай бұрын
@theoilykrafter Thank you. My Baofeng 888s is supported but the SFE S780H RADIO is not support. So I can't configure them. I tried contacting SFE
This is a great video and exactly to the point, however I'm still unclear why I would be doing this. Is it to make sure that all my BF888s radios share the same frequencies for each channel? And you replaced the settings with an existing file; where did you get that file?
@theoilykrafter
20 күн бұрын
I used Chirp to create the program that was written to the radio. After programming the first radio. I read from the next radio and copy and pasted the frequency table into the tab that I just read from the radio after saving the original configuration. Then after pasting would save and write to each subsequent radio to ensure that they all have the exact same program.
The software won't allow to change the language like some others do. That would be helpful as well
@theoilykrafter
4 ай бұрын
I am not sure that I understand the question. Are you referring to the language setting in Chirp ?
My CHIRP program says that there is "No response from radio" after clicking "OK" to "communicate" with it. Do you mind telling me how can I fix that?
@theoilykrafter
6 күн бұрын
There are a number of things it could be. A bad programming cable, an in correct baud rate on the COM port, an incorrect data bits and stop bit setting. It could also be that you have the wrong model radio selected or a radio that is not supported by Chirp.
great tutorial. fails for me with no response from radio
@theoilykrafter
3 ай бұрын
Thank you. Sorry to hear that you haven't had success with responses to your attempt.
@LeePyatt
3 ай бұрын
@@theoilykrafter i finally had success. required turning it on counting 2-4 mississippi and hitting the ok button.