Programming a Chevy Garage Door Opener | 3 Button Garage Door Opener on 2023 Chevy Traverse
Тәжірибелік нұсқаулар және стиль
In this video, I show how to program the 2023 Chevy Garage Door Opener. You will need to have your garage door handheld transmitter, be in your vehicle, and be pulled out of your garage. To program, hold down the button your want to program and you will see the red indicator light blink. Push your garage door transmitter while holding it 1 to 3 inches from your buttons. The light will blink quickly, releasing your transmitter. Push the button you just programmed and your garage door light will flash indicating the button is programmed. Release and hold down and your garage will operate.
Пікірлер: 40
i have a genie garage door opener, everything worked with programming the car. but, had to push the learn button on my garage door opener, and then 2 seconds with the button i selected in the car. worked! took forever to figure out that i had to push the learn button.
Very helpful, i have a liftmaster garage door opener and the programming worked the same way as you showed in the video.
I have a 2018 chevy traverse and a genie 1035. Clear all the codes on the chevy by holding 1 and 3 until it blinks rapidly. Once cleared, with the garage door open, hit the program button on the genie for approximately 1.5 secs and let go it will blink purple. Go to the car and hit the button desired on the car and hold the button on the remote that comes with the opener. You will see the rapidly blinking light that he talks about. This should sync. I did a little trial and error, but this is a super helpful video!
@richo8767
4 ай бұрын
Thanks for the comment. I could not figure out why the button would no longer program this way, but I had to clear the codes that way and then it worked.
Thanks! Worked perfectly.
Thank you for making it so easy.
Worked on first try! Super easy! Thanks so much!! 😊
@RandomReviewsHowTos
11 ай бұрын
You’re welcome 😊
Thanks! Worked!
Worked on a 2023 Z71 Tahoe. Thanks for sharing friend!
@RandomReviewsHowTos
Жыл бұрын
Glad it helped!
Thank you !
Thanks for the video it worked
Thank you
Thanks
Thank you sir Quick simple n easy
Thanks I tried no success it might have needed to be reset. But it did work on 2.
@sticksnstones140
8 ай бұрын
Just left an instruction filled comment on this page. Not sure what opener you are using, but check my comment and see if you haven't figured it out.
Hi, if i may ask. Do you like your 2023 Chevrolet Traverse so far? And which trim do you have RS, Primer or High Country? I'm possibly purchasing a Traverse High Country model this week.
@rzbrown3
11 ай бұрын
We just got a 2020 RS and it’s very nice
@Rachel_Lala
10 ай бұрын
I just got the 2023 RS, I love it!!!
@pattyl.3290
9 ай бұрын
I just got a 2022 RS it’s very elegant, so much technology easy to use, runs smooth spacious, you won’t regret it.
@dennisrees9615
6 ай бұрын
23’ redline we love it
This technique did not work for my 2021 Blazer. The Genie owner's manual did not work either. I had to push the Program button on my Genie 2028 until the light flashed purple. Then, I simultaneously pushed the hand-held remote button and in-car button until the in-car light rapidly flashed.
Where you holding the car button and the garage door opener at the same time for 5 sec or did you release the garage door opener
@RandomReviewsHowTos
Жыл бұрын
Holding at the same time. It's essentially picking up the signal and programming itself.
I cannot find my garage door opener, is there anyway to program without it?
@sticksnstones140
8 ай бұрын
You can buy an aftermarket remote off whatever site and program that to the opener. Once the opener is set you can program the car. I also left instructions for how I did mine in a previous comment.
What if you don't have a garage door opener? My car was stolen and that was one of the things we didn't get back when it was recovered. I just got my equinox but we still don't have a remote 😢
@RandomReviewsHowTos
3 ай бұрын
You can probably order a replacement and reprogram it all. I'd recommend that anyway considering your car was stolen. I'm sorry that happened to you.
@BrianaAnderson-po5sc
3 ай бұрын
@@RandomReviewsHowTos we already reset the box I just didn't want to have to pay for another one if I didn't have to
Can't get any of the lights to come on
Can I do this without garage door opener
@RandomReviewsHowTos
Жыл бұрын
I'm not 100% sure, but I don't think so.
@angeldolata8056
Жыл бұрын
I would like to know the same…
@sticksnstones140
8 ай бұрын
No you can't. But you can buy any opener online and sync it to your opener. And then you can follow his methods to get it to work. I also left a comment that has instructions for my Genie model that had an extra step.
It didn’t work for me. I have a Genie model 1128B garage opener
@sticksnstones140
8 ай бұрын
Hey man just left a comment with instructions in case you haven't gotten it fixed yet. Might be the model or method that is getting you. Check my comment above
ugh it didnt work for me :(
@RandomReviewsHowTos
Жыл бұрын
I'm sorry - same model? Try slowing down with the steps...