I enjoy this machine since a while. Thanks for the additional instructive measurements!

Best review of the pro300 on KZread!

That's the absolute best review for the Profitec Pro 300

@el_dani

Жыл бұрын

It‘s very far from an review

Great information, thanks! I think Pro 300 makes more sense for me as a home machine than the bigger brothers 600 and 700, which I have been thinking about to get. The fast startup time is just unbeatable on the 300. I’d rather wait 10 minutes than ~40 minutes what the big ones need for your first cup in the morning.

@holgerdanskeqwerty

5 жыл бұрын

I chose the 300 for the exact same reason. used the extra cash to buy a better grinder! love the 300 :) ( upgraded from Simonelli Oscar after 10 years of use)

BEST machine at this price point!

Curious as to why they decided to put a steam pressure gauge instead of a brew pressure gauge on the front of the machine? I would prefer a brew pressure gauge. Or better yet, why not a dual readout gauge, since there are two boilers? How would you be able to adjust the brew pressure or check the brew pressure of this machine, if at all possible? Oh, if only I could design my own machine. 😁

So if I get a new Pro 300 .... should I test and adjust the pump pressure if needed? I assume it's factory set correctly, but I would feel good about checking it. Once the pump pressure is confirmed to be set correctly, is it then "set it and forget it"? Would I need to check it periodically? If I didn't need to adjust the pump pressure too often, then I think this would be the espresso machine for me. Thanks for any comments by all and great video Clive Coffee!!

Hi. I would like to thank you for this great video that's full of knowledge and tips. I got one question where can I buy this pump pressure tool?

@carlcat

4 жыл бұрын

Saad: You can buy a pressure gauge with PSI or Bar markings at Home Depot or Lowes and the necessary adpaters to screw them onto your portafilter. I bought one for a little as 20 dollars. You can also order one on Amazon: www.amazon.com/Portafilter-Pressure-Gauge-Check-Kit/dp/B012WQ5XLK/ref=sr_1_2?gclid=EAIaIQobChMIiZyg8un15gIVDMNkCh0LyghFEAAYASAAEgKqo_D_BwE&hvadid=410054921015&hvdev=c&hvlocphy=9032457&hvnetw=g&hvpos=1t1&hvqmt=e&hvrand=16428171371725416991&hvtargid=kwd-3472568497&hydadcr=28330_11859632&keywords=portafilter+pressure+gauge&qid=1578549211&sr=8-2 Then bring your portafilter and gauge to a hardware store to get the correct adapter threads. You may not even needs adapter threads with this gauge since it's made for portafilters.

What size pitcher and type are you using in the video? Is this a 12 oz or smaller? Thanks!

Is it more difficult to descale this machine as opposed to a single boiler?

Do you have complete temperature measurement data?

I need 14.5 inches of clearance under my counter. Can the legs be left off?

Is there a pre-infusion for 3 or 4 seconds when brewing?

@clivecoffee

Жыл бұрын

No, there is not pre-infusion on the Pro 300. However, there is always a slow ramp-up in pressure in most machines with a vibratory pump before you reach full 9-bar pressure, so you're not blasting the puck right away.

i just pulled a trigger on this machine, not sure is i should of gotten the rs pro

@ukonthego

3 жыл бұрын

@em1 how do you like this machine

They dveloped very unfortune place for main and steam switches as well as for PUD display. In real life they may be wet and dirty.

There’s not really any tips here.