Pro Traction Tip: 2 Rimlocks is Better Than 1!
Спорт
One of the main keys to success with the Mousse Bibs is running two rimlocks on the rear tire. In this video, James demonstrates how to install the second rimlock properly, put the Mousse Bib and tire on while navigating both of the rimlocks, and a couple more tips and tricks for premo traction! We know installing a bib with two rimlocks is not an easy task - hope this helps!!
Connect with Inside Enduro!
►Check out our Website: insideenduro.com/
►Follow our Instagram: /
►Follow our Facebook: / insideenduro
►Subscribe to our KZread: / insideenduro
►Listen to the Inside Enduro podcast on all platforms!
Пікірлер: 88
Our bib drills are back in stock - get them here: insideenduro.com/shop/1-25-mousse-drill/
@antdx316
2 жыл бұрын
Supposed to add a bit of oil and going slow when drilling. Because what is being drilled doesn't matter too much as it's thinner and soft you can get away with it but on super hard materials.. going slow and adding pressure while oiling prevents it overheating and snapping the drill.
You should get some Motion Pro Bead Buddies. Nice video. Thanks for making it.
Awesome video, cleared up alot of questions i had about moose's, thanks.
Love the Sherco nail color, that's commitment !
If you don’t have an old valve stem, I’ve used steel stick to pack that hole and by George, it works damn well. Just a little bit and a backing of a piece of gaff/guerrilla to hold it in place while it sets. I love this channel and these dudes are real fuggin men. Thanks for all the info as always guys. You rock.
@InsideEnduro
Жыл бұрын
Great tip!
Excellent vid clear concise
@InsideEnduro
Жыл бұрын
Glad it was helpful!
Excellent video...! Cheers
@InsideEnduro
3 жыл бұрын
Thanks Carlos!!
Great video clarity!
@InsideEnduro
Жыл бұрын
Glad you enjoyed it
got my drill from you this week - drilled mousse is awesome
@felipedossantosdeandradesa9926
2 ай бұрын
Qual a diferença se não furar ?
How are you getting an air tight seal at the rim lock holes?
how about 3 rimlocks each 120 degrees apart? I saw a couple of gold riders using this setup on Xross this yr…I wonder if thats really useful🤷♂️
love your content..from Israel with respect.
@InsideEnduro
3 жыл бұрын
Thank you, much appreciated!
Great job tks
@InsideEnduro
3 жыл бұрын
Thank you!
Does the air come out on its own or do you pull the valve stem or push to drain?
Thanks for the information on 18:00 to get the tire over the rim lock!
@InsideEnduro
Жыл бұрын
Helps mega!!!
Very nice 👌🏽... thanks for sharing
@InsideEnduro
3 жыл бұрын
Appreciate it! Thanks for watching
@jeffmacdonald9386
3 жыл бұрын
@@InsideEnduro Hi guys love the videos awesome and very detailed. Just Wondering what altitude you guys ride at and what your jetting set up is thanks
I’m about to install and use my first set of mouse’s. My question is, with the TuBliss system, we use Armoral to lube the tire. It always dries and sets up fine. I’ve never had a tire rotate. That being said, can that be used as well as the window cleaner, or should one use nothing but the window cleaner?
Awesome video, thanks fellas. Quick question, when you run the gorilla tape around the rim, are you cutting out a section where the air valve comes through? Or are you blowing the air under the gorilla tape? Thank you!
@InsideEnduro
3 жыл бұрын
We cut the hole out :)
been doing 2 rim locks for years with tubes. Helps balance the wheels too as well as extra security in case of flats. A little more trouble changing tires but don't do that too often. Do you release the air once the bead is seated?
@InsideEnduro
3 жыл бұрын
Good call! No we don't usually release the air - it leaks out typically within a day. Might be a good idea to release it if you're going to go ride it right away though!
Sweet!
Just followed this guide and it has been hooking up on the 22’ TE300! Do you go through the xtrem quickly and lube both same time? What im trying to say is, if front tire is in good condition, do you still lube at a certain interval? Would really appreciate your input awesome and hilarious video!!
@InsideEnduro
2 жыл бұрын
Glad you enjoyed it! We only lube mousse bibs when changing a tire. No need to pull a bib out just to lube it.
@bowilloughby2403
2 жыл бұрын
@@InsideEnduroyupp thats what i was hoping hhaha thanks 👍
Very nice
@InsideEnduro
2 жыл бұрын
Thanks
What has your thoughts been on that tire? I just ran one and was surprised by it for a DOT tire on single track rocky root covered climbs. Not sure if i just got lucky for 350 miles on it or if it was just a good tire...
@InsideEnduro
3 жыл бұрын
It’s definitely one of our go to tires here in Montana.
Is the mousse paste same with silicone or rubber grease? If so i'll gonna try using rubber grease as replacement if possible
@InsideEnduro
Жыл бұрын
We do not use silicone because of the mess that will be created.
A lot of dad jokes right there! 😅 👍
What is your rim width?
Hmm... good idea.
@InsideEnduro
3 жыл бұрын
Thanks! With the two rimlocks, there's no way that tire is breaking off the rim. Let us know if you try it!
Logan bolopue runs 3 rim locks on his Sherco.
@InsideEnduro
Жыл бұрын
We have never had an issue with 2 rim locks.
Drilling with your left hand, didn't know that was possibl
@InsideEnduro
3 жыл бұрын
James is ambidextrous!
Two only for the rear? Not the front? Right?
@InsideEnduro
3 жыл бұрын
Yes just on the rear
Those firepower gromets look like water tap washers.
You left the air in the tire?
@InsideEnduro
Жыл бұрын
Full Bibs.
Fark ya ✌🏾
@InsideEnduro
3 жыл бұрын
Yeah buddy! ✌️
@HenryDarr
3 жыл бұрын
@@InsideEnduro 🤙🏽
Bro, where are you located? I’m not able to do some things mechanically and if you are even close, I’d come to you! You are so bloody hilarious--throw the inner tube in your local stream and everyone will think it’s a “seal” or I don’t know how you measure your nipples! I love this video your presentation rocks!!
@InsideEnduro
3 жыл бұрын
We are in Bozeman Montana. Thanks for the support
So many sexual innuendos hahaha, great video
@InsideEnduro
3 жыл бұрын
That's just "the tip" of the iceberg, check out some of our other ones!! Thanks for watching!
Oil that drill bit. It'll cut faster - even with aluminum.
2 rim locks on the front tire as well?
@InsideEnduro
Жыл бұрын
No just one
Sexy matters. Have a 2012 Factory 300SE on the way to add to the quiver!
@InsideEnduro
3 жыл бұрын
Heck yeah!
@wednesdar452
3 жыл бұрын
@@InsideEnduro That's 2021! ... don't think the 2012 version was counterbalanced!
About time to give away a 2021 300 SE Factory don’t you think boys?
@InsideEnduro
3 жыл бұрын
Whoa whoa whoa 🤫
@Drewski423
3 жыл бұрын
@@InsideEnduro just a suggestion lol! I like my ktm but I need a French Tickler in the garage too!!!
Whoever disliked this video sits when they pee
@InsideEnduro
3 жыл бұрын
We do sometimes 🤔
Muy malo para cambiar mousses, le falta sabiduria¡¡
my friend i am a proud european and i don't know the meaning of the 2 fingers, you who talk about it explain us there! like this 🖕🖕our like this ✌️?
@Hanibul_Lecktor
3 жыл бұрын
Totally situational lol !!! 🤟 is also acceptable when you've got a real wild one.
“Mousse Drill is available on our website..” FAKE NEW! They have been out of stock for awhile, was warned a few videos ago that they are flying off the shelves, thats on me for procrastinating
@InsideEnduro
3 жыл бұрын
We are working hard to restock - thank you for your patience! They sold out quick!
@smoking2strokes
3 жыл бұрын
Im on the Email list for restocking, after watching your demo i almost cried when i drilled my bib out with a 1.25” paddle bit the other day (it was Fugly)
@InsideEnduro
3 жыл бұрын
Hey 2Strokes4Trump - our Bib Drills are back in stock finally! insideenduro.com/shop/1-25-mousse-drill/
@smoking2strokes
3 жыл бұрын
@@InsideEnduro order one 2 days ago with a sweet IE Tshirt. Thanks for the update
Good video, terrible old dad jokes,
@InsideEnduro
2 жыл бұрын
Thanks
looks like a HUGE pain in the ass.
@InsideEnduro
2 жыл бұрын
Worth it!
You DONT have a "CLEAN" HOLE! I never saw you "DEBURR" it. Let the chips fall where they may I guess. One small sliver....
@justinkinzie4717
3 ай бұрын
MOUSSE DONT CARE ABOUT A SLIVER