It is always so rewarding to watch a skilled craftsman work his magic.

Amazing video that explains the whole refurbishment process clearly.

at min 6:32 what gun are you using ? and what kind of coating are you using ? thank you !

Brilliant job need my S8 Audi doing i live in Liverpool any ideas were too take the car too have the wheels done THANKS

the only video where someone shows this step by step without any bullshit

What a cracking job ya did there, very interesting to see how it’s done step by step 👍👍👍

nice work mate. do you apply the silver to the barrel or just leave it in primer?

What is the chemical you use to strip wheels?

Does the powder lay on top and you skim if off similar to wet paint? Never seen powder applied in a waterfall booth before this video.

Getting my Caddi wheels refurbished to hypersilver at Detriot Wheel and Tire, I hope they do a good as a job.

Thanks man. Your efforts are appreciated

Cool. But no torque wrench on the lug nuts?

@UltralydvaskingLillehammer

4 жыл бұрын

abs. mandatory on modern cars !!

@joapps8135

4 жыл бұрын

Most r not aware that incorrectly torqued lug nuts => warps rotors => steering wheel shakes when braking. BUT torque wrenches r sensitive to support hand placement (or lack of) wrt BOTH hands... keep free hand on socket head to support n maintain a consistent 90 degree angle (tests show how movement can affect the applied torque) and keep hand on grip at consistent spot (where u grab can dramatically affect torque...think leverage). also, if a lug nut is over tightened with your impact gun and then u finish off w the torque wrench as u did, the lug nut will of course be overtightened -- if it clicks without any turn, then do over. other critical tips: -do not loosen lugs ever with a torque wrench. use a normal socket wrench -completely loosen torque wrench to lowest torque setting and then tighten to highest setting 3X (yes, 3 times!) before each use -loosen torque wrench to lowest setting when storing -do not use cheap torque wrenches which can be inconsistent -chock wheels to minimize vehicle movement as u torque -tune torque wrench as recommended by mfgr -etc

Great video... a true Subject Matter Expert!!

Does that water get recycled or to the drain?

Hello what is the RAL color you use?

where are they located and how much for a 21 inch wheel

So lacquer is better than clear polyurethane? TIA

Hi sorry to bother you great video this might be a stupid question can you tel me whats the music called in the back ground

What a splendid job you done buddy, see ya next year when the wheels have been curbed again

Do you have any "recommendations" for Powder Coating preperations? Thanks!, -Thomas Port Orchard, Washington

@mako040472

5 жыл бұрын

Yes the recomendation is learn how to do it and dont ask stupid questions in you tube

@tkskagen

5 жыл бұрын

@@mako040472 I wasn't asking YOU 4Q!

Awesome job & Cool music.

where in Worcester at you located/

Question : For safety, why is the torque not checked on the wheel nuts before driving ?

@mako040472

5 жыл бұрын

Because he dont give a shit about the costumer just repair the rim

Hi, What product do you use to remove the powder coating?

@armandoreyes6730

4 жыл бұрын

It's somebody outside their know what is The chemical in the tank . He's using. Please email at armado60@gmail.com

how much does this cost for a full set of 19 inch wheels

wowowow you are a doctor!! where are you from?? big respect fom MONTENEGRO MNE :)

brilliant tutorial excellent welding and attention to detail is superb .Such a shame about the stupid extremely irritating loud noise in the background forcing me to keep turning the sound up and down .

hello, mate what is your postcode?

Perfect job!!

do you apply the primer while the wheels still hot?! should you wait them to cool down and the clean them again then ply the primer while they are cold?

What was the cost in US dollars ?

Where are you based

Do u now do diamond cut ?

What would you do if tyre pressure monitor leaked?

@mako040472

5 жыл бұрын

Fix ot again until stop leaking or buy another rim and pretend that i fixed it

Nice to see that you primed the wheels before powder coating.

@icarr121277

4 жыл бұрын

The primer is powder coating, the color is spray paint

Nice work! Though you forgot to copperslip where the hub and wheel mate. Also please use a torque wrench on wheel nuts. But otherwise nice work!

how much ? please...

Definetely a nice professional job.

Where are you located? Can I come by to refurbish my alloys?

What's the cost for 4 18 inches AMG wheels, 2014 model I want my done many thanks.

@user-wy9vf5kq4q

5 жыл бұрын

990$

@eduardosampoia5480

5 жыл бұрын

@@user-wy9vf5kq4q ouch

@MrAli171

5 жыл бұрын

Don’t think it will be that price in uk about £200 to £250

@ahoorakia

5 жыл бұрын

@@user-wy9vf5kq4q YOU CAN BUY GOOD SET NEW RIMS IN u.s FOR THAT PRICE

@John-dz5dv

5 жыл бұрын

Anywhere from £50+ a wheel

Very professional job. 👍🏻👍🏻👍🏻👍🏻

How much will be a job like this one?

Nice work

nice work man, congrats

Not polishing?

Where you based, need mine done ?

Step 7:57 is vital, not only for the safety of losing a wheel, break disc's disperse a lot of heat into your alloy wheels and if that heat carnt escape past the powder coating you will be soon replacing your warped disc's.

You don't need that stupid canned music on your video, the content is good as is.

This is the definition of done the proper way

How much to refurbish the whole set of 4 wheels?

@mako040472

5 жыл бұрын

The amount of 1 times 4

Those look nice good job.

How much does something like this coast

@maxn8904

4 жыл бұрын

For awhile probably but it always helps when you're going downhill.

Any relation to Deepa Takhar?

how much for that service

great video

Assume you are not in the US?

Where are you based ??

Great job dude 💯

Top job - I like your attention to detail. You have nice set up. What shocks me is the incredible number of nasty comments below. What is wrong with people that they think it is acceptable to be so disrespecful. You know who you are. Why so hateful? The guy is only showcasing his business. Do you go about your daily lives insulting people to their face - I suspect not. Don't get me started on the some of plain incorrect ideas / comments below......

A nice bit of TIG welding, not an easy process to master.

Wow, those wheels look awesome. Great job!

That's a proper craftsman right there

original music by Jeremih dont tell em :)

Nice work, he left without paying btw ;-)

@eksine

6 жыл бұрын

but he gave a thumbs up

@Jocek17

5 жыл бұрын

nice one hahaha

@MrShanghai34

5 жыл бұрын

Really!?!?!?! And he parked in a handicap space at that???

@michelnguyen4819

5 жыл бұрын

Lol, right.

@lavalgrenade5926

5 жыл бұрын

Dinosaurs

I don't get the 2 points on why to apply the powder on the hot wheel. To outgas the metal? That's fine, just let the wheel cool down afterwards and it will still be outgassed. And to see how much you put on? If i'm not mistaken you can get a mil guage for powder and even if not, a professional that does this all the time will know how much they put on. On a hot wheel you will lose some of that self levelling ability of the powder.

@johnreynolds2240

5 жыл бұрын

1) it saves time, no waiting to cool down, less time to get back upto temp 2) powder primers can tend to get a smoother finish hot spraying Just be careful as you can get sags in powder if you not experienced enough

@John-dz5dv

5 жыл бұрын

You heat the wheel up because alloy is porrouse your taking out the dampness air and any gases if you let the wheel cool down you could then get the air dampness back in. If you do the wheel cold you would get pin holes where the air dampness gases are coming out.

Like brand new!

NICE WORK

Basically, what he mean is you can't DIY, you have to pay for someone doing it( and delivery fees) then you got to pay for the mounting and recalibrating the tires including the re-alignment of the car, pretty sure they will convince you to do it since you just payed the price for refurbish your wheels.

@mako040472

5 жыл бұрын

Yep

great job on the wheels, hope your respirator is up to the job tho.

Looked at this and its dangerous not to mention the same price as new. Very hard to balance because the finish is not consistent on the rim.

@65Wonders

5 жыл бұрын

joe blow you are afucking tool stfu about what you don’t know to be true ya fucking idiot

Neighborhood shop that knows their stuff, 👍🏼👍🏼

Where are those guys?

@jumpinjojo

5 жыл бұрын

Vincent Leung West Dreyton.

Come to Miami you'd make Bank...

Great end results, products and services look great, I hope The lug nuts were torqued, and please consider using Eye protection, in all the processes, so you keep delivering awesome products, remember safety,safety safety Jose Kansas

I repaired my first wheel gouge in 1997. I used JB weld.

@FrustratedBaboon

5 жыл бұрын

You're not the sharpest tool in the shed are you ?

@jiakabery3550

5 жыл бұрын

@@FrustratedBaboon hey fucktard! I have video shit for brains. Just repaired a wheel a few months back. You're too stupid to think JB weld can fill a scratch in a wheel and work? You definitely describing yourself as a dull tool. Fucking Moron.... they fix cracks in Transmissions with JB weld. I'm sure it's gonna work to fix a curb mark on a wheel. You're an embarrassment to shithead comment Makers.

AMG - All Money Gone

OMG the AMG owner ran away without paying ........☺

Could not finish video due to the annoying sound track.

Beautiful. These ALL COLORS match so much ...

why is water trickling in 6:05

@stevefromlondon9175

5 жыл бұрын

catching any over spray

Good work but why did u use a drill to put the lug nuts on u should have used a torque wrench

@Thedataman1

5 жыл бұрын

That's an impact drill, same thing as a torque wrench.

@mathushan326

5 жыл бұрын

It could overtorque the lugnuts and get the lugs stuck in them

@Thedataman1

5 жыл бұрын

@@mathushan326 The drill has torque settings. Hey take a min and check out Torque drills, there are a lot of companies who make them.

10:10 Better to tighten with a calibrated torque wrench, than an impact gun...

@smokegreentree

5 жыл бұрын

Impact guns have torque settings....

@amana1480

5 жыл бұрын

@@smokegreentree Calibrated torque wrenches are the most accurate way to tighten to a specific torque setting, or to make sure you are not damaging the threads of the nut/bolt by overtightening...

@smokegreentree

5 жыл бұрын

@@amana1480 it's a wheel not engine or bolts that really matter. You genius you.....that's probably why you buy a torque wrench for the wheels since that's all you can probably work on. Yeah you aren't telling me anything I don't know. Let me guess you are under 25 and you know it all right? ....

@shawnmartin8485

5 жыл бұрын

Wow...a torque wrench for a tire....if it was a Lamborghini or Ferrari sure but it's just a mid range Benz....

@amana1480

5 жыл бұрын

@@shawnmartin8485 Doesn't matter what car it's for. When you have experienced what a pain in the ass cross threaded nuts and bolts can be, due to the lazy habit of people using impact guns to TIGHTEN fully, you will always use a torque wrench or hand tool to do the final tightening. The best tyre places I know use a torque wrench on every single car, when tightening bolts or nuts, doesn't matter whether it's a Kia or a Bugatti....

>GOOD JOB

Looks the same to me

opps!!!!!!!!!!!!!! forgot to torque the nuts with a torque wrench

"Time for the customer to go back to work at his gas station."

@vaz21212

5 жыл бұрын

Back to petrol station after the cars been up on bricks for two days in a disabled space while wheels are done

@2326TOM

5 жыл бұрын

envy!

@andiman45

5 жыл бұрын

pumpin gas no doubt

seems cheaper to do it yourself with rattle cans or just buy new wheels

@easley421

5 жыл бұрын

Go buy a new Mercedes rim from them and tell me if it's cheaper. Even my VW has ridiculous priced parts. Add AMG and hold onto your wallet

@eksine

5 жыл бұрын

@@easley421 I always check out eBay and Craig's first. Also I would never be stupid enough to buy Mercedes or any of those brands. I don't throw my money in the garbage

@easley421

5 жыл бұрын

@@eksine WTF? AMG is garbage? Some people can afford and appreciate the engineering and development going into these cars. For you to pretend there's no difference is based purely out of spite, jealousy or animosity. Either way I hope you Enjoy your Ebay car parts.

@easley421

5 жыл бұрын

@@eksine because when you go to college and take a 'reading' class, you then make enough money to appreciate finer things in life. Next time you see that $70k car don't even look. Remember that's not for people like you and enjoy your poverty stricken life. My tires cost more than your whole car and it makes me smile.

@eksine

5 жыл бұрын

@@easley421 I have almost 30k in savings and about equal that in line of credit. Yeah I'm so poor plus you still look like an idiot, nice try

A good craftmanship right there .

Great video but it's all industrial. If you had the tools y'd be able to do the same. 👍🏿

THE CAR IS NOT ON JACKING POINTS. IS IT ???

good video and content but lose that awful noise(music..)

Low profiles created a whole new industry of rim repair......

Not bad for a tenner a wheel.

You are breathing in a lot of carcinogens when applying the various powders and fluids.

@jonedgar5996

5 жыл бұрын

He is wearing a face mask.

@sunilcherianpullockaran8817

5 жыл бұрын

@@jonedgar5996 Check out from 6:20 to 6:30 when he is applying sparkle silver. At 6:26 change spelling from spakle to sparkle.

As industrial art I could mount a weld-repaired wheel on the wall of my garaje, BUT NOT ON ANY CAR

Warranty repair.

good vid, but quite a few mistakes.

With a turbine sandblasting machine you will do everything in one time. (no more manual sandblasting and chemical immersion)

Superb welder

No soap? Wow what a waste of time.