For a tip when starting these 390/360/352/460 with points, you can't leave the key on too long. otherwise, you will burn them points up. Your Bendix is going out on your starter, plus you need a bigger carburetor650/700

@Rustwrangler

2 ай бұрын

Thanks for the tip on the points. Once I threw a new starter on there it was a night and day difference, starts like a champ now.

@user-ss3mq5jh3x

Ай бұрын

Old school, ignition, points condenser & such , but yeah , oh yeah , no doubt burn them points out , like that.

@fordnut4914

26 күн бұрын

Yeah i burned few up in past😂

Really awesome truck. Great video

At one time for me it was a 1965 F250, with a Thunderbird 428 and 1960 Ford Super Stock cast iron headers. Had 2.5 inch dual truck mufflers and turn downs. Standing near at idle and your chest could feel the exhaust pulsations. Art Carr modes to Ford automatic from same Thunderbird.. Cab over camper and accelerated past 90 mph going South up the I5 Grapevine. Great for trailing horses and I miss it.

@Rustwrangler

2 ай бұрын

Nice, that sounds like an awesome truck!

Awesome video. I learned a few things from watching it. I hope to find a 1965 F250 custom cab camper special in caribbean turquoise one day. My father bought one brand new in upstate NY and he got a nice slide in camper with it. So many wonderful memories of either going to hunting camp and Grandma's house traveling in that truck. Tbis will give me something to do in my retirement one day. Cheers!

@Rustwrangler

Ай бұрын

Thanks a lot! Seems like sometimes it takes some effort to find these old trucks especially in a specific color, but they’re still out there. Good luck finding one!

Never heard of a “high boy” truck ……tractor , yes . I assume that’s another term for a lifted 4x4 truck ? Nice ride .

@bradleymadosh911

Ай бұрын

Ford made them they have a step up by the door. A lot of KZreadrs call truck high boys when they are not because they don't know the difference. If you check on here you will see and no e have the step up

Power booster. Disconnected and plugged .

Keep a propane bottle & torch tip with you. Its great for chasing down vacuum leaks just crack open the valve a lil bit & work your way around the engine

@Rustwrangler

2 ай бұрын

Great idea, thanks for the tip! I’ll have to try that out next time.

That's the Ferd F-Teen Thousand!!! It is technically 8 tanks.

The process is how you learn

R.W.,, GREAT VIDEO AND TRUCK,, SO MANY WIRES .. THANKS FOR THE VIDEO I LEARN ALOT FROM YOU ...

@Rustwrangler

2 ай бұрын

Yessir, it was a mess of wires! But it’s cleaned up now and looking and running great! Thanks

you always come up with the coolest vehicles to work on :) but looks like you will have your hands full with the wiring mess, hope it all goes well! :), I just helped a friend with a fuel gauge problem related to sending unit, I found it hard to find the proper sending unit (impedance) to match the fuel gauge impedance (in ohms measured) they vary widely in ohms and if not matched it would show wrong fuel level or if open can make the gauge peg backwards, good luck ! but all this makes it fun :)

@Rustwrangler

2 ай бұрын

Oh yea, this was a super cool truck! And extremely fun to work on. That’s interesting info about the fuel gauge, is that due to mixing and matching parts from different vehicles, or new parts not built to the specs needed?

@stevent3450

2 ай бұрын

@@Rustwrangler I typed in a long reply on how and what i used to simulate a sending unit to test and match a fuel gauge and either I didn't click reply or Utube removed it maybe because I had given the brand name and or because I abbreviated wire wound potentiometer as "POT" maybe I forgot to hit reply or enter and it erased it all :)

I'll take it!😊 1:39

Im doing the same thing with a 65 mercury. Im putting it on a 80s chassis with a 351 5speed.

Hello yea taking over someone elses project can be a pain nice to see you got things worked out .p.s. On the passenger side fender does it say ( Farm and Ranch if so i seen this truck at the plowing match in lynden sat it was parked next to me i did a double take because of the size and height then your video poped up of that same truck today sweet 🏆🤔

@Rustwrangler

Ай бұрын

I don’t recall seeing farm and ranch on the passenger fender, might be another truck like it running around.

40:40 I can't hear you over here😂

I have always wanted one of those 4wheel drives. They look great that way

@Rustwrangler

2 ай бұрын

Yes they do, this truck looks beefy in person, it’s great!

Maybe check the gear at the end of the distributor

I had a 62 . Mine had 10 inches of clearance between the top of the tire and the fender arch . I put a 390 automatic in it a two stage mastercylinder and power brake booster . Loved that truck .yours sits to low . Tire to fender is wrong .

@Rustwrangler

2 ай бұрын

Yea it is pretty close to the fenders, but surprisingly enough, it doesn’t rub.

My thoughts... vacuum leak from the brake booster/hose? Thin coat of grease on the carb gasket (both sides) to help the seal and prevent it from sticking? Water in the fuel tank? Since its a rebuilt FE, it would be a good idea to use some carb cleaner to test for intake to head vacuum leaks, but you need to pull the valve covers to do that.

@Rustwrangler

2 ай бұрын

Good idea on the thin coat of grease on the carb gasket, I did at one point unhook and plug all of the vacuum lines to eliminate any possibilities of a bad line.

@RustBeatersDerelicts

2 ай бұрын

@@Rustwrangler Yep, once you eliminate the air and fuel issues, all that leaves is electrical/timing. BTW, the way my dad showed me to adjust timing at idle, he used a timing light and a vacuum gauge at the same time, find that sweet spot of enough initial advance without making it hard to start.

@Rustwrangler

2 ай бұрын

@@RustBeatersDerelictsoh interesting, I’ll have to try that out.

Plug hose going to brake booster.

Shouldn't the rotor be pointed at the first piston on passenger side when top dead center

@uoykcuf2128

2 ай бұрын

yes it should point #1 piston on passenger side not #1 on the cap

That's a 2 wheel drive look at the bed! It's had 4x4 added.

@Rustwrangler

2 ай бұрын

That’s correct, it’s on a highboy chassis.

The last 10% of a build is almost always where interest is lost. The little things are time consuming and it's hard to visualize the project moving forward when you're doing things like wiring, body work, etc. Throwing in a motor or doing a body swap is more visually satisfying.

@Rustwrangler

2 ай бұрын

Absolutely, there were times when I was building my c10 that I would walk away from it a month at a time and had to pick away at a few little things here and there to get that excitement going again.

@stanleyhape8427

2 ай бұрын

I have a buddy that starts tons of hobbies. He spends a ton of money on them but doesn't finish them. He built a building to "work " and store them in. When that building became filled He tore it down and built a bigger building. Sounds like he's rich, right? Nope, he constantly complains how he is one foot away from the poor house. And it's true, I do his taxes. It's super easy but he paid a service to do it previously. Example. He bought a used John Deer rider. Stripped it all down ,new motor, new deck , new tires and authentic green paint and decals. All the top tier equipment to paint it. And it sits in the building unused because it needs a new starter switch. As does the Ford Ranger . He did sell the Mercedes that he fully restored for half of what he had invested in it🥴

@Rustwrangler

2 ай бұрын

@@stanleyhape8427haha, nice! That sounds like the American dream!

@stanleyhape8427

2 ай бұрын

@Rustwrangler You are right. He's happy and has an eternal belief that tomorrow will take care of itself.

@user-ss3mq5jh3x

Ай бұрын

Got that rite .

Heater switch pulls out then turns

@Rustwrangler

2 ай бұрын

Yes, I figured that out later. Haha.

Nice! Excited for this series, I have a similarly set up truck except on a '71 chassis with 460 and C6.

MAYBE GET A READY MADE WITH FUSE BOX COMPLETE WIRE SET UP FROM A AUTO WIRE HARNESS COMPANY I THINK IT'S CALLED / E/Z WIRE HARNESS /

@uoykcuf2128 yes it should point #1 piston on passenger side not #1 on the cap then you have move the plug wires on the cap to #1

Bad idea setting the carb on battery terminals 😂

Check the lug nuts, my wheel came off when i got mine going. You never know what the last guy did.

@Rustwrangler

2 ай бұрын

Definitely, I checked them, they were good and tight!

@ChrisJEllis

2 ай бұрын

@@Rustwrangler oh and nice find that condenser. Most don’t know these days how bad the points and condenser can mess with you.

Maybe new points from leaving key on.

Why would anyone give up on a project like that? I would give my left you know what for a truck in that condition. My dream truck is a mid 70's F250 high boy. I had a 77 many years ago but sold it like an idiot. Now you can't find one for decent money. Hope it works out. You will have a nice truck when it is finished...

@Rustwrangler

2 ай бұрын

Oh yea, these trucks are getting harder and harder to find, I know of another body swapped 70 highboy just down the road that needs rust repair, body work and paint, and the guy thinks it’s worth gold.

Did you don't know if you cancelling vac dadada or condenser. fixed it

@Rustwrangler

Ай бұрын

Condenser was definitely what fixed it.

Nice job figuring out someone else's mess. That's always a tough job.

Awesome! Are you interested in vehicle lighting stuff sponsorship?

@Rustwrangler

2 ай бұрын

Possibly, could you email me at Therustwrangler@gmail.com

@suparee

2 ай бұрын

@@Rustwrangler Great! We did. Please check it out later. Don't miss the spam if you fail to find it in the box.

Is the truck for sale buddy

@Rustwrangler

2 ай бұрын

Yes it is!

🛻🛻🛻🛻🛻🛻👍

Turn idle up maybe thats your problem

@Rustwrangler

Ай бұрын

Ended up being the condenser.

Lol you say good think it tirns over soni think? And proceeds to burn up the starter 😂 jk but you will if you keep doing that

HEATER KNOB TRY PULLING IT OUT NOT TURNING IT

@Rustwrangler

2 ай бұрын

Yea, found that out later. Thanks