The problem is Rockwell broke off to Meritor who continued shutting their union shops down across the USA and now not only have the stockholders realized how good we were, it’s biting them in the ass with substandard quality. In Newark, Ohio we were at the forefront of research and development and continuously had people working to keep the wrinkles ironed out. Now it’s done by low wage employees who don’t get paid enough to care.

@willmann30

3 жыл бұрын

Shame on capitalism. It's capitalism with a capital C that's ruining this country/world. Greedy ass investors and cut throat shareholders want us working class to have NOTHING. I have no problem with paying for quality done by skilled labor. My problem is paying for shit so the wealthy can blame working class people for demanding better wages. This country is infected with filthy leeches.

A fully reconditioned rear end that was overhauled and,most importantly,had the pre- load,mesh and contact patch set up to factory spec. With the best will in the world this is a job best left to an expert on the job.

Do not blame the oil change the damage was already done, normally the first thing to go if the wrong oil is used is the crown wheel and pinion. The power dividers suffer greatly due to excessive spin out when the drivers are to slack to use the diff lock in slippery conditions.

if the guys at the TA found a big piece of metal in your oil chances are it's already to late so it's not the guy at the TA'S fault it was probably only a matter of time and changing the oil had nothing to do with that

Awesome Video!🎥

Hey it hurts, and there goes the profit for the next couple of months. My engine dropped a valve one month after I finished paying for the truck. $22,000 later, I was back on the road. Still paying. That's over now, but it was pain at the time. Not even mentioning, every year a new set of tires. Stay safe out there.

@OutBackTruckerBucky

5 жыл бұрын

I am sorry about that, Not a good feeling , How many miles did your truck had before engine went?

@oby-1607

5 жыл бұрын

That engine had over a million, so I guess I got my money's worth. It's all good for now. We will see, I guess. The worst thing was it was a valve keeper that did it. It was funny, as the shop asked if I wanted the new improved valve keeper. Well duh. Especially since it only cost another hundred bucks. A buddy of mine was going thru Boise ID and the input shaft sheared off of his transmission. All he could do was coast to a stop. $4200 later, he was on the road a week later.

@KulinBan777

5 жыл бұрын

What kind of tires are you buying that you can only get a year out of them, Ive never heard of that...maybe you should stop taking heavy load for 20 cents more and drive lighter loads, 3 years later im still on MIchelin recaps and can still get at least 6 months

I think you should hone that ring gear bro, maybe that would work

El chofer tiene que estar más pendiente, porque este daño primero avisó por ruido y luego ruido y vibración. Para que la caja bloqueo se vaya completa como se dañó esta, ese daño avisa con tiempo.

@hectordem08

5 жыл бұрын

Por suerte no se le desarmó el bloqueo y cayeron fragmentos, sino se le va la corona y el piñón también.

My truck has problem when I turn differential switch on I hear air does something but only one rear wheel spinning on passenger side. What can be the problem? What's need be checked?

cách chia vòng tua của các trục như thế nào

The driver should pay even more attention while driving. Because this damage of the lock gearbox makes a notable noise due to wear and then when it is critical and close to break down you can feel the vibration. Something is going wrong and you should stop and check, as it happens. Fortunately, the lock gearbox is damaged, but complete, because is something gets broken, any fragment could fall and also the crown and pinion get damaged, then the complete carrier is a garbage piece.

i rebuilt the my on kw t600 94 $1400 dollars total with labor

@alishahrezaei8675

4 жыл бұрын

Pedro Sanchez where did you rebuild yours?

What were the symptoms? I'm getting a grinding noise, especially when heavy and backing up, think this could be it?

@OutBackTruckerBucky

6 жыл бұрын

When you are hearing the grinding noise what speed are you traveling ?

@arnoldramos39

6 жыл бұрын

OutBackTrucker Buck slow, usually when backing up into a parking spot. Or loaded a bit heavy around 43000 and taking off.

@OutBackTruckerBucky

6 жыл бұрын

Take it to the shop have them Jack up the back off the ground and spin it slow and have some one hear it , you might be able to identify the where the noise is coming from

@armandsauciuc

5 жыл бұрын

@@arnoldramos39 I've replaced bearings because of a grinding noise when back up with heavy loads,and that didn't fix it I found out that my fifth wheel was dry Some grease on fifth wheel fixed the grinding noise

@redline9536

3 жыл бұрын

@@armandsauciuc 🤣

I herd u cant run diff lock all the time cause it wears stuff out

Alguien puede decirme que marca ymodel9 es este difetencial

How much did that cost you sir ??

ouch well that sucks

How much did it cost you to fix it ,I am having a same issue

@insanevideos6736

5 жыл бұрын

abdulmejid Alamin Asalamu alaykum bro, i got the same problem right as i speak, im in dallas i found a cheap private shop and they fixing it the parts that broken, they try to bushes me to charge the whole thing but I refused cause I don’t have 4500 dollar so now it is much cheaper, im sure but i will find out the 3 pieces i need how much it will cost me,markaas waa sidaas ugaas arinku

How much does a repair like this cost and what parts were changed? (Is it an assembly?) Thanks.

@OutBackTruckerBucky

7 жыл бұрын

This is where the mechanics get you, when some one is in this situation , mechanics do not want to fix it part by part or sell you by parts instead they want you buy the whole power divider and be done with it. price is $4500.00 out the dealer, in this case it was $2500.00 picked up local shop, under warranty

@johnbeckman8916

7 жыл бұрын

The way they suggested may be the best in the end. Those other parts were compromised by the same oil and metal shavings. I assume "$2500.00 picked up local shop, under warranty" means "used parts"? Sorry to hear about your misfortune but it was good of you to share the experience to help others like me. Thank You and I hope that your rig keeps rolling!

improper oil i'd wager. That sucks

Looks like you had the wrong oil used! Needs an extreme pressure hypoid oil in there,car or light truck oil not high shear enough and will accelerate failure.

@OutBackTruckerBucky

7 жыл бұрын

Very true, that's what happened

T/A mixed the oil. Destroyed it! You can't mix oil.

did they replace all the bearing

@OutBackTruckerBucky

8 жыл бұрын

All i know is that I felt an vibration

@73superglide62

8 жыл бұрын

+Trucker Buck there must be a lot of the driver ing the great roads out there

Using the diff lock too much....shock load!

things just wear then brake and it just like blame it on something

Fall synthetic is full-synthetic it’s all the same

Replacing power dividers gears could cost more than buying it all assembly.

@EPAGHGDDEXPERTjohnnyboy

6 жыл бұрын

N Tatic not true

@christopherlastname7638

5 жыл бұрын

No it's not this is what I do for a living I dont think all the gears are bad

Meritor mt40

That fork is fine thay are ripping you off !

only a damn fool would go to ta for anything !!! they do more damage to your truck trying to fix it .

These MBA (Mercedes) axles are the worst axles in the world. I have these axles/diffs on my truck, my forward diff just went again, this is the 4th time rebuilding it in 2.5 years. I'm not even going to rebuild these axles this time, overly priced piece of german junk. I'm probably going to be getting Meritor or Spicer, just swap both axles out completely. I'm tired of this junk, plus these MBA diffs cost a lot whether you get them rebuild completely or buy parts separately to rebuild them yourself.

@KulinBan777

5 жыл бұрын

I have never heard someone say "German Junk"...I'm pretty fucking sure they make the highest quality shit out there, especially when it comes to diesel engineering. I think that's on you and not the manufacturer

@tyflesh

5 жыл бұрын

@@KulinBan777 He's right the MBA diffs are the most expensive to replace and even more to repair, noone wants to repair them just replace, I got a 1.1mil out of mine and 1.5 yrs on new ones so far so good.

Hecha Mierda. Jajajaja

sux

They don't speak English. Why bother even trying?!

@papajr221

4 жыл бұрын

Dude who cares if they get the job done and probably cheaper than 4500