Power Bank Module - Type-C USB 5V 2A Boost Converter Step-Up Power Module for Lithium Batteries.

Hi guys ! we use power banks to charge mobile devices when we are away from home or when there is a power cut. Also, a power bank can be used as a power backup system even for security cameras that operate with 5v. So, in this video, today we will talk about a power bank module that can be used to make a DIY power bank at low cost and how to make a power bank using the module.
--Parameter--
Input voltage range: 5 ~ 5.5V
Charging cut-off voltage: 4.2v/4.35v
Charging current: 2.4a
Boost output voltage: 5V ~ 5.15v line loss compensation
Boost output voltage ripple: 100mV
Boost output current: 2A
Boost conversion efficiency: 92.5% 3.6V input, 5v2a output
Battery static current: 30uA
--Function--
* When the load current is less than 50mA continuously, the output will be turned off.
* Support external key,
* When the charging current drops to 100mA the charging cycle will be automatically terminated.
* When the battery voltage drops below 4. 1V, the charging cycle starts again.
* When the battery voltage is lower than 2.8V, the battery will be pre charged at 180mA.
* It supports discharging while charging.
------MORE VIDEOS------
Li-ion/LiFePo4 Battery Protection 100A BMS 3S 4S 5S 12V 16.8V 21V
• Li-ion/LiFePo4 Battery...
IP2312 Quick Fast Charging Board.
• IP2312 Quick Fast Char...
SZBK07 300W 20A Buck converter
• SZBK07 300W 20A Buck c...
How to make Power Backup UPS For Router and Modem
• How to make Power Back...
Wireless Charger Transmitter And Receiver Modules.
• Wireless Charger Trans...
PWM solar charge controller
• PWM solar charge contr...
How to modify TP4056 module
• How to modify TP4056 m...
ECC Easy Chip Charge Module
• ECC Easy Chip Charge M...
Tp4056 Li-ion battery charging module
• Tp4056 Li-ion battery ...
How to use CKCS BS01 Mini DC-DC Step Up Module
• Tp4056 Li-ion battery ...
How BMS modules are Working
• How to make Li-Ion Bat...
How to make Power Backup UPS For Router and Modem
• How to make Power Back...
How to use XL-6009 Buck Boost convertor
• How to use XL6009 Buck...
XH-M604 Battery Cut-Off Module With Display. Configuration and Full Review.
• XH-M604 Battery Cut-Of...

Пікірлер: 73

  • @prizmacreations1821
    @prizmacreations1821 Жыл бұрын

    Highly appreciate you explanation. 👍

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    than you bro 😎

  • @lahirubro111-gz9mr
    @lahirubro111-gz9mr8 ай бұрын

    හොද පැහැදිලි කිරිමක් .තවත් මොඩියුල් ගැන විඩියෝ දාන්න ❤good luck

  • @rash_desilva
    @rash_desilva Жыл бұрын

    Keranne kiyanne hitapu video ekak...thank you ♥️

  • @wasanthithissera9260
    @wasanthithissera9260 Жыл бұрын

    Explaination is great 👍🏻

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    thank you very much

  • @m.m.i.fernando8407
    @m.m.i.fernando8407 Жыл бұрын

    Thank you for the valuable video ❤

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    Glad it was helpful!

  • @carloshuaman5088
    @carloshuaman5088Ай бұрын

    Gracias x la explicación del interruptor pensaba que me estafaron al comprar..miles de gracias..

  • @erandamadushan7185
    @erandamadushan7185 Жыл бұрын

    Hodatama pahadili karala tiyenawa niyamai.😍

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    බොහොම ස්තූතියි 😊

  • @wizardmathsolver4541
    @wizardmathsolver4541 Жыл бұрын

    Nice explanation😮

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    thank you very much 🤜🤛

  • @kinshukpal5540
    @kinshukpal55408 ай бұрын

    I have the same looking module, only the ic marked as "hotchip pb0063a"... when i use this module to charge 3x18650 batteries in parallel, charging current is not exceeding 0.3amp, although the used 5v adaptor can provide upto 2.4amp. Any idea what's going on here??

  • @hanymagdy2095
    @hanymagdy2095 Жыл бұрын

    Dear, your explanation is excellent, and also the translation is in Arabic. We missed the explanation. There is no material like this. Fast shipping. Please

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    thank you very much. i will add arabic translations for the videos

  • @DilnuwanAmaraweera
    @DilnuwanAmaraweera6 ай бұрын

    වචන නැ සුපිරිම සුපුරි පැහැදිලි කිරීමක්

  • @michaelstevenmacleod2930
    @michaelstevenmacleod293011 ай бұрын

    Csn i use this at replacement charger csse for my earbuds? If i can, where can i connect the 2 earbuds on the module?

  • @maheshmnaiir
    @maheshmnaiir4 күн бұрын

    Can i connect charge led indication sepparately ?

  • @malruwangallage3839
    @malruwangallage3839 Жыл бұрын

    👍

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    Thank you very much

  • @royandreanjulio-5477
    @royandreanjulio-547711 ай бұрын

    Hi sir. I have a 3pcs 3.7-4.35 lithium battery which is Each of them is 2000mah. Do I have to use dc module step up so that ip5306 module works properly,i am waiting for your answer,thank you.

  • @freesoundsforyou
    @freesoundsforyou8 ай бұрын

    Hello everyone Could you please let me know where can i find the certain wiring diagram of this modul? Looking for it for a while, but have not found...

  • @prabathmunaweera9584
    @prabathmunaweera9584 Жыл бұрын

    👍👍👍👍👍👍👍👍👍👍

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    👍

  • @sirminion6199
    @sirminion6199 Жыл бұрын

    Good explain.. can usb C replace with micro usb ?

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    thank you. Yes you can Solder micro usb port to external pads

  • @Robotronic12345
    @Robotronic12345 Жыл бұрын

    Lm2596 ic එක ගැන video එකක් ඔනේ🤗🤗

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    කරන්නම් 👍

  • @kaib9203
    @kaib920326 күн бұрын

    I am powering a device with low power, so the converter shuts off automatically. Is there a way to stop this behavior?

  • @edmundmorris3227
    @edmundmorris3227 Жыл бұрын

    Can this output 5v through just the USB C port? Is the USB A port necessary to connect?

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    usb c port for charging . Usb A port for output . If you need usb c port for the output you can solder external usb C port to output soldering pads

  • @pawanmalviya9949
    @pawanmalviya994910 ай бұрын

    Is it auto detect load and starts the boost. 2) is it auto detect no load and shuts down. 3)is it charge mobile without battery using type c charging input voltage 5v.

  • @SantoS-jf3mu
    @SantoS-jf3mu7 ай бұрын

    Hello, but i can't put with this module a battery with 3,7 volt for charging?

  • @kaib9203

    @kaib9203

    26 күн бұрын

    All good. 3.7V batteries are being charged with 4.2V

  • @hanymagdy2095
    @hanymagdy2095 Жыл бұрын

    Can the charger charge more than 6 batteries, thank you 

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    yes you can The maximum charging current is about 2.4A. Depending on the current you can use several more batteries. But if you use more batteries, the charging time will increase

  • @trustmeiamfromjamshedpur2676

    @trustmeiamfromjamshedpur2676

    Жыл бұрын

    ​@@theelectroroot4919 i ahve 20 batteries

  • @maungmaung7238
    @maungmaung72388 ай бұрын

    No Out auto detect error how to made?

  • @ashik82
    @ashik82 Жыл бұрын

    Hi dear...did u try the 4.35v jumper? I tried, but it still gives 4.20v

  • @elingesaurio4150

    @elingesaurio4150

    Жыл бұрын

    I have the same problem

  • @SaKe909
    @SaKe909 Жыл бұрын

    Can I give like 12v input

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    No it’s only work with 4.5v-5.5v. But if you want to use it with 12V you have to use Buck converter module (step-down module)

  • @pwintphyu5180
    @pwintphyu51806 ай бұрын

    High mah ?

  • @densilfernando5937
    @densilfernando5937 Жыл бұрын

    හෝද පැහැදිලි කිරීමක්

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    බොහොම ස්තූතියි

  • @sasiniwanigathunga7244
    @sasiniwanigathunga7244 Жыл бұрын

    meka lankawe ganna thiyana shops monada

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    colombo වල 1st cross එකේ shop වල අනිවාර්‍යෙන්ම ඇති

  • @ishanlakmal6664
    @ishanlakmal6664 Жыл бұрын

    Mekata 18650 3.7V battery use karanna berida? 4.2v - 4.35v battery witharada puluwan?

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    use karanna puluwam. 18650 Kiyannd 4.2 v battery tamai. 18650 cell ekak max 4.2v walata charge unama tamai 100% fully charge kiyanne. Itin oyata kisima aulk natuwa 18650 Cell use karannna puluwan

  • @ishanlakmal6664

    @ishanlakmal6664

    Жыл бұрын

    Thanks brother..❤ oya hodata explain karanawa.. subapethum digatama karagena yamu..🥰

  • @ishanlakmal6664

    @ishanlakmal6664

    17 күн бұрын

    Brother man meka gaththa 18650 battery 2k set kara.. battery nam charge wenawa eth phone ekata connect karama balagena innakota battery discharge wela yanawa. Eth battery wala voltage eka hodata thiyanawa..ai ehema wenne?

  • @tipsandtrics623
    @tipsandtrics6237 ай бұрын

    මේ මොඩියුල් එකට බැටරි 6ක් දෙනවා නම් bms අවශ්ය නැද්ද.

  • @trustmeiamfromjamshedpur2676
    @trustmeiamfromjamshedpur2676 Жыл бұрын

    Mere pass 20 piece 3.6 v 2000 mah lithium iron Battery hai ....agar mein sare Battery ko parallel connect karke powerbank bano toh kya te circuit kam karega....aur heating issue ke liye bada wala heat sink laga denge, thermal paste ke sath , kya ye work karega???? Agar nahi karega toh please koi Powerfull , long lasting, 3amp , quick charge , over charge protection, , bms including, , koi asa master circuit board bataye jiska help se hum 50,000 mah power bank bana saken , please help me it's my dream project

  • @TruthLoversKoSALAM-fg8dh

    @TruthLoversKoSALAM-fg8dh

    Жыл бұрын

    50,000mAh ke ap 5s4p circuit banao (20 batteries) 21V - phir step down buck converter se usko 12V per convert karo aur us per 12v to 5v multi port circuit laga lo

  • @yudhavalkyrie7568
    @yudhavalkyrie756811 ай бұрын

    how to remove stanby mode from that charger

  • @dwieztro6748

    @dwieztro6748

    10 ай бұрын

    same, how to always enable without key pin?

  • @axemods03

    @axemods03

    8 ай бұрын

    ​@@dwieztro6748Probably bridge the switch

  • @govind3170
    @govind3170 Жыл бұрын

    Where can I get

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    Ali express or Ebay

  • @govind3170
    @govind3170 Жыл бұрын

    Buying link?

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    search model name in Ali express

  • @postscriptum1667
    @postscriptum16673 ай бұрын

    4:36 не работает 4.35, в обоих вариантах 4.2 макс

  • @chandrapalakudavithanage1735
    @chandrapalakudavithanage1735 Жыл бұрын

    මේකට battery දෙකක් හෝ තුනක් පමනක් යොදන්නත් පුලුවන්ද ....

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    parallel පුලුවන්

  • @hashendevinda8142
    @hashendevinda8142 Жыл бұрын

    Ayye battery 20000mah ekak hadanna ganna ona powerbank module eka mokadda

  • @theelectroroot4919

    @theelectroroot4919

    Жыл бұрын

    ඒ වගේ ලොකු එකක් හදනවනම් ip5328p වගේ හොදයි. මේකෙ pd quick charging එහෙම තියෙනව. Review එකක් දෙන්නම් ඒ ගැනත්

  • @hashendevinda8142

    @hashendevinda8142

    Жыл бұрын

    @@theelectroroot4919 oke විතරයි da thiyenne quick charging thiyenne

  • @hashendevinda8142

    @hashendevinda8142

    Жыл бұрын

    @@theelectroroot4919 eka ganna පුළුවන් link ekak danna පුළුවන් da

  • @AroshaSL
    @AroshaSL4 ай бұрын

    2024 කීයද

  • @dhanukasansala9189
    @dhanukasansala91898 ай бұрын

    ඔය ලිතියම්.අයන් බැටරි එකක් කියද 😢

  • @gayanmalinda475
    @gayanmalinda475Ай бұрын

    10000mah da puluwan meken uparima

  • @hashendevinda8142
    @hashendevinda81426 ай бұрын

    Ayye meke fast charging nedda

Келесі