🎉🎉🎉🎉Race saw action!!!!! Can't wait to see you at Sawfest!
@novicelumberjack
11 ай бұрын
Oh no! You're gonna be there! Hahaha! Me too.
@afleetcommand11 ай бұрын
Clever "Mandrel" A LOT easier than the bar stock machined to slip fit & slot for a cutting tool I did....and they prolly end up with the same result :)
@crazyfeller570411 ай бұрын
👍👍 been debating to cut the piston/cylinder skirt for a while. Food for thought…at bdc, the piston is no longer pushing anything up the transfer. My thought is to measure the square surface of the transfer/s and be sure there is always at least that much during the downstroke. Granted, mixture is coming from everywhere in the crankcase so concentration on just the cylinder wall will still be over doing it…even using that “formula”. I would imagine folks eventually figured out, taking it to the base just eliminates additional measuring and gets the job done.
@shawncaudill42411 ай бұрын
I can't wait to see it run. I'm sure it will be a screamer
@nseric123311 ай бұрын
I bought a 2 inch sanding pad for a drill then ground it down to 48mm to sand the squish in a couple of 48mm saws. 2 inch is very close to 50mm so it would work for a 372 as is. It was 10 bucks and came with a bunch of disk.
@IndianaDoug11 ай бұрын
Don’t sell yourself short on this build. You’ll do well I think 👍🏻
@nateolmsted899
11 ай бұрын
Come on doug don’t let them off so easy I like give them a hard time 😂
@yenerm11411 ай бұрын
That other cylinders transfers had cracks in same place the other did lol
@dubbssawshop11 ай бұрын
👍🏻 buddy!!!! My G372 is built very similar to yours. The FT cylinders are petty nice to work with. I think you'll have a very strong runner there 💪🏻and can't wait to try it out. Sticky sandpaper is very handy to have around.
@novicelumberjack
11 ай бұрын
Yeah, it didn't give a nice flat squish all the way to the edge, but it did cut through all the plating and made it much easier for me to cut with the mandrel.
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
👍🆙D
@dubbssawshop
11 ай бұрын
@@novicelumberjack definitely makes it easier to get thru the plating, sometimes that stuff is laid in there thick 😆 🤣
@dubbssawshop
11 ай бұрын
@@Doc-Cole_Trickle-of-Chainsaws good morning buddy 👍🏻 I am up from my power nap and not ready to roll haha
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@dubbssawshop Good Morning T-Dubb!
@charlesjenks271011 ай бұрын
Cutting cylinder skirts will make better flow.
@jamesh813611 ай бұрын
Rock on dude
@TightWad111 ай бұрын
Good R&D platform 2 experiment on!
@TightWad1
11 ай бұрын
Hooo...o!
@novicelumberjack
11 ай бұрын
Yep, if I screw it up, literally no one cares. Not even me.
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@TightWad1 HOOOO!
@shawnglacken305511 ай бұрын
Go for it! 👍👍
@novicelumberjack
11 ай бұрын
I'm goin!
@jjm325411 ай бұрын
Those cylinder cracks were interesting to see.
@novicelumberjack
11 ай бұрын
Turned out that they were like that on the Farmer Tec cylinder too, just not NEARLY as bad.
@shakdidagalimal
11 ай бұрын
@@novicelumberjack dangit I was really looking at the 372xp cloner now I'm going stihlborn
@georgesjunk11 ай бұрын
Do a 2 piece cylinder.... you got the lathe. Let's see you attempt!
@novicelumberjack
11 ай бұрын
Not allowed for the race I am competing in.
@georgesjunk
11 ай бұрын
@@novicelumberjack ah shucks..... but would def like to see your journey to get something like that going. 🤞 Thanks for all the educational content!
@Doc-Cole_Trickle-of-Chainsaws11 ай бұрын
👍🆙BigGuy
@novicelumberjack
11 ай бұрын
Doc!
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@novicelumberjack Wuz🆙
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@novicelumberjack Getting close to 8K!
@cajun319711 ай бұрын
Thumbs 👍🏽
@aaronpowell488511 ай бұрын
Sounds like a good plan👍🏻
@novicelumberjack
11 ай бұрын
Time will tell. I may not get top five, but it should make for a good runner.
@ladislavgazdik759511 ай бұрын
It is not cracks. It has every single one.
@novicelumberjack
11 ай бұрын
Yeah, I noticed it in the Farmer Tec cylinder too, but not nearly as bad.
@coolestguyontheplanet72311 ай бұрын
Again , how. Do you get 1.1 likes ?
@novicelumberjack
11 ай бұрын
You got me man. KZread does some weird stuff!
@shakdidagalimal11 ай бұрын
If the piston goes out of round because you hacked off half the skirt HAHAHAHAHHAAA (this channel is fun) Oh wait, it's under the pin so it will RIP THE FREAKING PIN OUT split down the lower middle and remain at the top of the cylinder -"Chrome Dome Blown" will be it's new name. LOL Loses the whack off but thinks it won anyway "chrome dome blown" ahahahahahaha Good luck
Пікірлер: 41
🎉🎉🎉🎉Race saw action!!!!! Can't wait to see you at Sawfest!
@novicelumberjack
11 ай бұрын
Oh no! You're gonna be there! Hahaha! Me too.
Clever "Mandrel" A LOT easier than the bar stock machined to slip fit & slot for a cutting tool I did....and they prolly end up with the same result :)
👍👍 been debating to cut the piston/cylinder skirt for a while. Food for thought…at bdc, the piston is no longer pushing anything up the transfer. My thought is to measure the square surface of the transfer/s and be sure there is always at least that much during the downstroke. Granted, mixture is coming from everywhere in the crankcase so concentration on just the cylinder wall will still be over doing it…even using that “formula”. I would imagine folks eventually figured out, taking it to the base just eliminates additional measuring and gets the job done.
I can't wait to see it run. I'm sure it will be a screamer
I bought a 2 inch sanding pad for a drill then ground it down to 48mm to sand the squish in a couple of 48mm saws. 2 inch is very close to 50mm so it would work for a 372 as is. It was 10 bucks and came with a bunch of disk.
Don’t sell yourself short on this build. You’ll do well I think 👍🏻
@nateolmsted899
11 ай бұрын
Come on doug don’t let them off so easy I like give them a hard time 😂
That other cylinders transfers had cracks in same place the other did lol
👍🏻 buddy!!!! My G372 is built very similar to yours. The FT cylinders are petty nice to work with. I think you'll have a very strong runner there 💪🏻and can't wait to try it out. Sticky sandpaper is very handy to have around.
@novicelumberjack
11 ай бұрын
Yeah, it didn't give a nice flat squish all the way to the edge, but it did cut through all the plating and made it much easier for me to cut with the mandrel.
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
👍🆙D
@dubbssawshop
11 ай бұрын
@@novicelumberjack definitely makes it easier to get thru the plating, sometimes that stuff is laid in there thick 😆 🤣
@dubbssawshop
11 ай бұрын
@@Doc-Cole_Trickle-of-Chainsaws good morning buddy 👍🏻 I am up from my power nap and not ready to roll haha
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@dubbssawshop Good Morning T-Dubb!
Cutting cylinder skirts will make better flow.
Rock on dude
Good R&D platform 2 experiment on!
@TightWad1
11 ай бұрын
Hooo...o!
@novicelumberjack
11 ай бұрын
Yep, if I screw it up, literally no one cares. Not even me.
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@TightWad1 HOOOO!
Go for it! 👍👍
@novicelumberjack
11 ай бұрын
I'm goin!
Those cylinder cracks were interesting to see.
@novicelumberjack
11 ай бұрын
Turned out that they were like that on the Farmer Tec cylinder too, just not NEARLY as bad.
@shakdidagalimal
11 ай бұрын
@@novicelumberjack dangit I was really looking at the 372xp cloner now I'm going stihlborn
Do a 2 piece cylinder.... you got the lathe. Let's see you attempt!
@novicelumberjack
11 ай бұрын
Not allowed for the race I am competing in.
@georgesjunk
11 ай бұрын
@@novicelumberjack ah shucks..... but would def like to see your journey to get something like that going. 🤞 Thanks for all the educational content!
👍🆙BigGuy
@novicelumberjack
11 ай бұрын
Doc!
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@novicelumberjack Wuz🆙
@Doc-Cole_Trickle-of-Chainsaws
11 ай бұрын
@@novicelumberjack Getting close to 8K!
Thumbs 👍🏽
Sounds like a good plan👍🏻
@novicelumberjack
11 ай бұрын
Time will tell. I may not get top five, but it should make for a good runner.
It is not cracks. It has every single one.
@novicelumberjack
11 ай бұрын
Yeah, I noticed it in the Farmer Tec cylinder too, but not nearly as bad.
Again , how. Do you get 1.1 likes ?
@novicelumberjack
11 ай бұрын
You got me man. KZread does some weird stuff!
If the piston goes out of round because you hacked off half the skirt HAHAHAHAHHAAA (this channel is fun) Oh wait, it's under the pin so it will RIP THE FREAKING PIN OUT split down the lower middle and remain at the top of the cylinder -"Chrome Dome Blown" will be it's new name. LOL Loses the whack off but thinks it won anyway "chrome dome blown" ahahahahahaha Good luck