I am definitely using this shop . Under standing for the why gives value to the work . Thank you great content.

@headgames

2 ай бұрын

Awesome! Thank you!

@zc18crx

2 ай бұрын

The did my k20 head, best decision I've made

Finally a K series video, more of it please!!!!!

@headgames

2 ай бұрын

we can do that!

This is why whenever I have a US based or CA based inquiry I always always suggest and direct them to HeadGames… they can never go wrong with the choice of going to HeadGames😎 awesome work and video Dave and good selection words 😎

@headgames

2 ай бұрын

Thanks for your kind words

@SRDmotorsports

2 ай бұрын

@@headgames but uncle Johnny needs a raise 😂

@headgames

2 ай бұрын

@@SRDmotorsports he’s been hiding behind the scenes lol

@SRDmotorsports

Ай бұрын

And there you go 10k goodness!!!!

Must be nice utilizing the long shank burs! I've used the big Makita grinder for 20 plus years and bent soooooooo many long shanks, and I've cut them down to 4" or 5". I'm definitely considering new equipment. Just thinking back to how many manifolds I could've done so much more work to with full length long shank burs 🤦‍♂️

@headgames

Ай бұрын

Yeah I hate that big Makita. I made an L out of one of our burrs as soon as I turned it on. I threw it under the bench and never went back. You would love the smaller Makita. If you do a lot of manifold porting you might get some kick back in tight areas, and there is many area's where your not supporting the burr, I would suggest to buy 2. You will break the plastic bearing inside the grinder. Other than that, it really is a game changer and so easy to hold all day. And you can spin it full blast with a 3/4 burr 6" long with no problem.

Thanks Dave, excellent work and technical explanation. Regards Goyo

@headgames

2 ай бұрын

Welcome!

awesome video full of knowledge

@headgames

2 ай бұрын

Thanks!

Great videos! I like the Honda head videos. I have two B16 heads.

@headgames

2 ай бұрын

Very nice! We will do more Honda!

Good morning Uncle Dave

@headgames

2 ай бұрын

Good morning beautiful

Head games can you explain the pros and cons of hand porting compared to a cnc port job or a combination? What and why would I choose one experienced porting company over another? Also if you can do a video of which head components are better than another. Supertech, Ferrea, Brian Crower.

@headgames

Ай бұрын

CNC vs hand porting we can certainly do that. Which brand is better, without pissing off vendors we work with is kind of impossible. BUT, we have shown things to look for. They all have their place.

Love the explanation. What are the cfm improvements at low mid or topend. Cheers

Wanna see a 420a Mistu or SRT-4/ PTGT head ported. Was told with +2mm I/E valves you can open it up quite a bit. But I don’t trust that! It ultimately takes your word before I believe it lol.

@headgames

2 ай бұрын

Sadly you won't see that on here. We haven't done a 420A head in many years. And certainly wouldn't be using that big of a valve if we did. But do appreciate you commenting and kind words!

@burnz3132

2 ай бұрын

@@headgames maybe I should send a few lol. I know not really much of anyone else wanting to seem them

and first again!

@headgames

2 ай бұрын

can u show us porting tips for subaru EJ heads please?

@headgames

Ай бұрын

kzread.info/dash/bejne/fa2ts5V7m8q2oNY.htmlfeature=shared

@headgames

Ай бұрын

kzread.info/dash/bejne/ZHll3MeBZc7fgJc.htmlfeature=shared

@headgames

Ай бұрын

kzread.info/dash/bejne/rJ9n0apmlbaaprw.htmlfeature=shared

@headgames

Ай бұрын

there is a few, there is a whole series on EJ

@AmirPomen

Ай бұрын

@@headgames thank you very much for the "heads-up" ! 👍👍👍 Lovely... 😘 Cheers ☕☕

Has anyone done any out of the ordinary experimenting. I have this idea about making air straightening grooves at the beginning of the port all the way to the throat by grinding with a small dremel. Chrysler had air straightener vents on their hood scoops. Try it on a junk head and flow test it

@arturozarate1752

2 ай бұрын

If your grooves ran parallel to the length of the runner and were shaped to be "fins" you may see increased port velocities. Properly placed of course. One fin at the center of the floor before the short turn for example. That's proven to be beneficial on a single intake valve.

@headgames

Ай бұрын

@@arturozarate1752 agreed. I think he is talking about making trenches. Is that correct @chrisopher? If so, I don't think that is beneficial.

@arturozarate1752

Ай бұрын

@@headgames trench warfare?🤣🤣🤣

Ej heads difference between the casting. 🤷‍♂️. Dual AVCS

@headgames

2 ай бұрын

Only problem is I don't know what head comes in what car. Like I know the heads, but I am sure people would want what that head comes in. I would need a buddy lol

🇦🇬 ⭐️⭐️⭐️⭐️⭐️. 🙇🏾‍♂️

80 Subscriber left!

@headgames

2 ай бұрын

Less than a week at this pace!

Honda heads are already oversized as it is. The ports don't need to be bigger at all.

@headgames

2 ай бұрын

You don’t need to make them bigger per say but you can make them better. Shape matters.

@rolandotillit2867

2 ай бұрын

@@headgames Exactly! This guy knows.

Get it digitized and cnc port it. why you still hand porting you can never match a machine.

@headgames

2 ай бұрын

We might digitize a pocket port at some point, but we still have to blend every head that comes out of the machine. The machine can spit them out but it is still a casting so you are dealing with core shift and they are not all the same. A hand knows where the port is, a machine only knows where it should be.

@arturozarate1752

2 ай бұрын

Yeah the cnc process might save a little time and the cut would be the same cut it was programed to make, but the shadowing will be blended by hand and I've had better flowing short sides after hand blending. Why you love the machine so much?