Polaris Xplorer 400 Chain Adjustment
Автокөліктер мен көлік құралдары
Polaris Xplorer 400 Rear Chain Adjustment
Some info off google. , but i like my way still. (there was no need to colapse the rear on mine As the rear shock sucks)
by the book ,take a tie down strap and tie it between the rear axle and the rear bumper. Tighten it down so as to colapse the rear suspension so that the rear axle and the transmission output shaft are level with each other.then 1. Loosen the chainguard 2.loosen the eccentric bolts(2) 3. Insert a pin punchthrough the sprocket hub and into the eccentric axle housing. 4. Roll the 4wheeler ahead or back until the proper tension is achieved. (about 1/4 inch of slack)5 . tighten the eccentric bolts to 60ft.lbs 6. tighten the chain guard allowing 1/8 inch of clearence between it and the rear sprocket.
Пікірлер: 27
Thank you, this is the exact system my 95' 300 has. I couldn't figure it out, will try when I get home.
i have a 1993 350l trail boss and i can confirm its the same way to adjust the chain. great video that covered what you needed to know with out a shit ton of extra garbage. great work !
Thank you. I found this video very helpful.
you make it look easy, i still cant get my back axle to turn forward
Thats good for a concentric drive vehicle. For a regular one you normally would strap the back down not for the load like you said but to align the angle of the rear sprocket and the one from the transmission. For models that have the brake caliper on the rear axle you would also need to loosen those bolts.
i have a 96 Polaris Sport 2x4... would it be the same process to adjust the chain on it as well ?
What year is you xplorer? I have a 98 and have to replace the sproket hub, sproket and chain.
what would happen if you just tighten those bolts in back till the are tight tight would that be bad for the machine??
We got the same wheeler now boss!!
@starpuss
2 жыл бұрын
They are not too bad of a Quad , But this one the Crank bearings started to go on her Seems like a pretty commom problem with them and really a easy fix.
is it possible put sprocket on other side so can put a motorcycle engine into it
Thanks
The little white decal to the right of your hitch ball says to make proper adjustment while the suspension in collapsed. To do this, I take a ratchet strap and hook one end to the frame near the brake light and the other end down near the hitch ball and ratchet down the suspension. Then I proceed like you do. The decal says 1/4" slack while suspension collapsed. Then decal says, "Torque eccentric bolts to 60 ft/lbs.
@starpuss
10 жыл бұрын
What you did not watch the vid??:? I said that in the vid lol...
Thanks brother. Go throw some dirt!
Mine keeps coming loose do u have any idea why?
@jakelee6296
2 ай бұрын
Chains prolly stretched or not tightened enough I think my 99 scrambler 400 streched it’s chain or loosened on me ima check it out tomorrow
Do you have A video of the swing arm bushings?
@starpuss
3 жыл бұрын
no sorry i dont.
The owner manual tells you to do it just like this.
@kroberts12321
7 жыл бұрын
how
I dont have a clue what you did you dont show what it is your doing or how your doing it get real explain and show
@stevenreissr1938
7 жыл бұрын
should have set camera down, and focus...... looks like your setting on a "paint shaker", also you never explained how ya did it, show and tell dude ..
@blaykntucks
2 жыл бұрын
If you 2 imbeciles need a step by step and are too inbred and dumb to read the damn owners manual then you shouldn't be trying to repair shit yourselves.