THANK YOU, I've watched a few videos on this subject and they all left out critical information. You on the other hand are totally comprehesible.

@foreignriders

2 жыл бұрын

Thank you. I tried my best

Doing mine right now, Awesome Job showing how you did it!! Helped me out a lot!

@foreignriders

3 жыл бұрын

Great to hear that . Glad I can help

Great video👍 very simple and step by step helped me alot to not forget anything thanks man👍

@foreignriders

4 жыл бұрын

No problem. Glad to help

Great seeing more DIY videos out there

Hell yeh this was exactly what I needed

Thanks for video!!! Life saver

That was a really good video man!!

@foreignriders

3 жыл бұрын

Thanks

Thank for the video. I'm was all mess up with the bearing order and can't put it back...

Great video 📹 You should have showed us how you took out that pin !!!!

@foreignriders

3 жыл бұрын

You just get a bolt that’s smaller than the hole and begin tapping on it. It comes out fairly easy

@christiancaloro8088

3 жыл бұрын

@@jaredsanger5620 yup this sucks

Man, this is the exact video I was looking for, where did you get your axle from? Thank you for this.

@foreignriders

Жыл бұрын

Glad it helped I bought it on eBay

Great video bud! Thank you! Question though, do I absolutely NEED the glass of orange juice?

@foreignriders

3 жыл бұрын

It’s your preference for what to drink

@sauljustice9668

2 жыл бұрын

InstaBlaster

Having a tough time removing the pin to remove from differential, did you run into same issue? Any tips?

@foreignriders

3 жыл бұрын

No . Just find a bolt alittle smaller than the hole on the axel. Slowly tap the pi out so that you don’t break anything

Im really screwed. I was changing the a arm bushings on my 99 scrambler 500 4x4 and noticed the cv shaft poped out and was just in the boot with 3 balls. Gigiddy! Anyways i took off the hub and reorganized all the balls. Now im going through hell to get the shaft back in. If i slide the shaft in to hub first then i cant get the splines through that big hole. If i put the splines berings and clutch thing through first then i cant get the shaft in. I even took off the shock. Managed to get everything in that way but now the dam shock wont go in to place. Im to broke to go to a mechanic if not i would’ve had a way better machine please help

@foreignriders

9 ай бұрын

Have you lifted the machine by the frame to get the shock to decompress and it might go in

Hey what are the torque specs and what kind of fluid did you use?

@foreignriders

3 жыл бұрын

I really don’t remember the torque specs I was going off the manual and I used hub oil from Polaris

How'd you get that pin out

@foreignriders

Жыл бұрын

You can get a rod that’s alittle smaller and use a hammer to hit it out or I used a Fillip’s screwdriver to hit it out

What is the part number for new pin?

@foreignriders

2 жыл бұрын

7661913

I don't think you put the last bearing in before that washer😲

Where did u buy the axle?

@foreignriders

2 жыл бұрын

I bought the axel on eBay

Just replaced mine and now it acts like it’s trying to pull that way or like it’s binding up. Anyone had a similar problem?

@foreignriders

3 жыл бұрын

That can happen if the axel was shorter than the original one

why are you replacing it?

@foreignriders

3 жыл бұрын

I’m replacing it cause the other side went bad and I decided to buy both front axles and replace them instead of one

What kind of fluid?

@foreignriders

3 жыл бұрын

I used oem fluid from Polaris

@bradjenkins932

3 жыл бұрын

ATF

@rouletteroller

3 жыл бұрын

Demand drive fluid, do NOT use atf if you want your 4 wheel drive to work

Went to do this then realized my strut housing was fuckkkkeddddd

@foreignriders

2 жыл бұрын

Dang that really sucks

just tap out the pin yeah ok

@foreignriders

2 жыл бұрын

Mine tapped out with a punch