I have never seen such a great teacher....................keep it up.......Thank you very very much

@MrElgamal77

3 жыл бұрын

It's my pleasure

@MuhammadImran-ul5ww

2 жыл бұрын

@@MrElgamal77 kindly also upload Rehman frame analysis method

Great explanations throughout. Thank you!

Thank you for these lectures. Great work.

Thank you for the great enlightenment, on this particular analysis of structures.

Thank you very much for your lesson sir, that's such a well explained topic!!

شكرا لك ولكل جهودك دكتور ...م محمد العراقي

Thanks so much. Very explanatory

Thanks for your efforts

You are a great professor. Thank you for your videos, they have been of great help to me.

@MrElgamal77

2 жыл бұрын

Happy to help. You are welcome.

Thank you very much Professor. I am looking forward more of your lecture about Plastic Analysis. Your lectures are really helpful and clear.

@LightBearers_ngn

4 ай бұрын

Hello

Appreciated hard work Thank you!!

@singhprakash6515

3 жыл бұрын

Hey which country u belongs? I m from india

Thank you My lecturer in university used virtual power instead of virtual work. I mean he multiplies load to velocity. And for internal power, he multiplies moment to rate of rotation. I dont know which one is better but this video was more understandable.

excellent videos! are you able to do the same analysis but for two storey frames?

Thank you, professor. Great apresentation.

@MrElgamal77

2 жыл бұрын

You are welcome.

Very good and understandable stuff thank you If you don't mind would you add one with distributed loads.

Good lecturing Sir, thank you. Do you perhaps have the BMD available for the last 2 examples?

Please can you go over a load horizontally in the middle of the column with a vertical load, where the horizontal beam has 2Mp?

How are the upper bound lower bound and uniqueness theorem used?

Hi Dr, if it is required the minimum plastic moment is that mean that we need to get the plastic moment from the beam mechanism then from sway and then from the combined action and take the lowest one ?

im so greatful for this video

@MrElgamal77

2 жыл бұрын

Thanks.

do you have videos about yield line method ?

Great explanation. Thank you.

@MrElgamal77

4 жыл бұрын

Thanks. Please share with you coleagues.

@climatechangecrisis9882

3 жыл бұрын

@@MrElgamal77 Ok!

what an awesome set of videos. That was a pleasure to watch. Brilliant! Just one question, How would I treat a UDL, convert this to a point load and solve the same way?

@amanchhetri7765

2 жыл бұрын

in case of udl, when we calculate external work done as: load*deflection ; the value of deflection will be in terms of area.. that means u need to calculate area under the udl. triangles are formed in plastic analysis .. so similarly in case of udl we use 1/2 b*h where b is the entire span of udl and h is the deflection acting at the mid section of udl when we get the value of area that becomes our deflection .. hope it helps u mate

Well explained.

@MrElgamal77

2 жыл бұрын

Thanks. You're welcome.

doesnt the fact that the horizotal and vertical loads being difffernt cause the angle theta to be different for the beam and column

pode pôr legenda no vídeo, para eu poder traduzir?

if two frame has the same minimum value then both will collapse ?

Greatful

@MrElgamal77

4 ай бұрын

Many thanks

If MP Is replaced by EI what will we do

15:27 if you're taking moments at C why did you include the C mp? shouldnt the equation just be Mp- Xd*4 = 0 since the MP at C will be eliminated?

Can you do video about designing slabs and plates using yield line method?

@MrElgamal77

3 жыл бұрын

I may do that in the future.

Jasakalaah dr your lectures are help full for civil engineering students will you uplaod other lectures

@MrElgamal77

3 жыл бұрын

I will do IN SHAA ALLAH

Kindly sir also upload the Rahmen frame analysis method

@MrElgamal77

2 жыл бұрын

Sorry. I am not familiar with this method.

if there is no horizontal load then is there no sway mechanism

@Phoenix67614

3 жыл бұрын

That is correct.

In example 1 how do we know which side is compression and which side is tension??

@MrElgamal77

3 жыл бұрын

The moment direction is always opposite to the movement of the element. For Ex, if a column is rotating clockwise, the moment at it ends will be count clock wise. This is also applicable for beams. The tension is always at the tail side of the moment and the compression is at the arrow side of the moment.

Dr.S.

كيف يتم حساب رسمه العزم لاخر مثال ؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟؟

@MrElgamal77

2 жыл бұрын

في المثال الاخير الانهيار كان فقط في الكمرة العلويه. لذلك يمكنك رسم العزم في الكمرة فقط و طرف العمود العلوي. في الطرف السفلي من العمود يوجد عزم بنصف قيمة العزم عند الطرف العلوي.

@ 14:51 I dont understand how you got 0.5 to find 12.5

@MrElgamal77

2 жыл бұрын

I just took the moment about C = 0 this will result to the following equation Mp + Mp -Xd*4 = 0 then xd = 2Mp/4 = 0.5 Mp. It is already explained and the equation is given I the video. I hope that you understand it.

عايز ترجمة عربى

يا دكتور اذا اغلب متابعينك عرب لماذا تتكلم انجليزي

@MrElgamal77

4 ай бұрын

لأن التدريس عندنا بالجامعة لازم بالانجليزي. كمان يوجد كتير متابعين ما يعرفوا عربي. هل رأيك اغير للعربي؟