Piston and Ring installation for Predator 212,Honda gx200, and clone engines
Жүктеу.....
Пікірлер: 21
@jnate3316 ай бұрын
I kicked an exhaust rocker following your instructions to the T . Set it at 5 and no problems yet
@markstreet74312 жыл бұрын
Thank you sir. I wasn’t sure about which ring went where. Luckily i got that exact type piston. From u. Thx again
@ol-man-duffyj6888 ай бұрын
GG strikes again with the BOOK OF KNOWLEDGE 🙏🏻 🤲 Thank you
@AllGreatTruths2 жыл бұрын
I have a 196 clone and I'm removing the connecting rod and piston to throw some new rings on with a fresh hone. Can i safely reinstall the rod onto the crank,torque it down and go?
@NFSINSANEАй бұрын
Great video, exactly what I was looking for!
@shaunthompson1935 Жыл бұрын
I ordered a short block gx200 clone and the piston was already installed and the arrow on the piston was pointing up . That's how it was delivered to me
@TheGrayGoatGarage
Жыл бұрын
I would correct that before running the engine. The pins are offset and the triangle or dot must face the pushrod area
@markday2198 Жыл бұрын
My black ring ( center ring ) doesn't flex at all once installed on piston . Can't depress to install piston into cylinder .
@thesw313tspot82 жыл бұрын
my motor has a 65mm piston. what rings would i need
@dejonjennings37672 жыл бұрын
what size gap do you need for it?
@ulyssescontreras43602 жыл бұрын
What’s size is your flathead and rod
@ulyssescontreras43602 жыл бұрын
What size do you need for a non hemi rod and piston
@Partnerthedog
2 жыл бұрын
What do you mean, you didnt say what engine. Gx200 196 clone or 212 predator. Then you go on the website and shop for your engine. It tells you what parts fit
@SHADOWO052 жыл бұрын
No need to oil/lubricant the rings?
@Rabbit.760
3 ай бұрын
I would
@joshuaboey366Ай бұрын
Do you need to offset the rings 180 degrees out???
@joshuaboey366
Ай бұрын
Each rings slot I mean
@TheGrayGoatGarage
Ай бұрын
@@joshuaboey366 Yes, I set my ring gaps 180 degrees apart. and have the end gaps by the pin. This is something that has been debated for years about what is the proper way. This may not be what everyone does, but it works for me.
@stanleyshults6427 Жыл бұрын
What about clearance on wrist pin,u never said about it,,or piston bosses,,rings could , B ALTERED IN DIFFERENT LOCATION ALSO,,HELLO WAKE UP FOLKS!!!!
@TheGrayGoatGarage
Жыл бұрын
Please do your own video that shows what you are talking about and link it here. We could all learn from you! Share the knowledge!
@aleidabianchi1434 Жыл бұрын
I did it myself with the Woodglut plans. I think this is the best way to find out how to build it.
Пікірлер: 21
I kicked an exhaust rocker following your instructions to the T . Set it at 5 and no problems yet
Thank you sir. I wasn’t sure about which ring went where. Luckily i got that exact type piston. From u. Thx again
GG strikes again with the BOOK OF KNOWLEDGE 🙏🏻 🤲 Thank you
I have a 196 clone and I'm removing the connecting rod and piston to throw some new rings on with a fresh hone. Can i safely reinstall the rod onto the crank,torque it down and go?
Great video, exactly what I was looking for!
I ordered a short block gx200 clone and the piston was already installed and the arrow on the piston was pointing up . That's how it was delivered to me
@TheGrayGoatGarage
Жыл бұрын
I would correct that before running the engine. The pins are offset and the triangle or dot must face the pushrod area
My black ring ( center ring ) doesn't flex at all once installed on piston . Can't depress to install piston into cylinder .
my motor has a 65mm piston. what rings would i need
what size gap do you need for it?
What’s size is your flathead and rod
What size do you need for a non hemi rod and piston
@Partnerthedog
2 жыл бұрын
What do you mean, you didnt say what engine. Gx200 196 clone or 212 predator. Then you go on the website and shop for your engine. It tells you what parts fit
No need to oil/lubricant the rings?
@Rabbit.760
3 ай бұрын
I would
Do you need to offset the rings 180 degrees out???
@joshuaboey366
Ай бұрын
Each rings slot I mean
@TheGrayGoatGarage
Ай бұрын
@@joshuaboey366 Yes, I set my ring gaps 180 degrees apart. and have the end gaps by the pin. This is something that has been debated for years about what is the proper way. This may not be what everyone does, but it works for me.
What about clearance on wrist pin,u never said about it,,or piston bosses,,rings could , B ALTERED IN DIFFERENT LOCATION ALSO,,HELLO WAKE UP FOLKS!!!!
@TheGrayGoatGarage
Жыл бұрын
Please do your own video that shows what you are talking about and link it here. We could all learn from you! Share the knowledge!
I did it myself with the Woodglut plans. I think this is the best way to find out how to build it.