Pentair Mastertemp 250 Gas Pool Heater Not Running Step by Step Repair of Gas Sensor
Жүктеу.....
Пікірлер: 34
@kens.37297 ай бұрын
Hello 👋 Tom. Nice to Meet you. Keep up the Strong 💪 Efforts and Thanks for Helping make the Trades Great Again. 👍🙏
@tbofinger1
7 ай бұрын
Thank-you stayed tuned for more great content!
@MikeyPipesOrlando
7 ай бұрын
Thanks, you too!
@scottmaz40637 ай бұрын
I knew it was going to blow with pump on. 😂 job well done Tom
@MikeyPipesOrlando
7 ай бұрын
🙏
@scottmaz4063
7 ай бұрын
@@MikeyPipesOrlando guess he got a little bit jumpy with the camera now. He'll be alright
@TasoV.7 ай бұрын
Happy New Year and thank you for all of the informative videos.
@MikeyPipesOrlando
7 ай бұрын
Happy new year!
@scottvolage17527 ай бұрын
Hi Tom Nice to meet you. Happy New Year.
@MikeyPipesOrlando
7 ай бұрын
Hi Scott. It’s me.
@tbofinger1
7 ай бұрын
Thank-you! Stayed tuned for more great content! Happy New Year 🎆
@Poolmedic6 ай бұрын
On the control panel there is a “Mode” button that has three functions as indicated in the box. Press the Mode button until the screen reads “Service”, your are now in Service Mode. Once in service mode you can manually control all your equipment, filter pump, heater etc via the buttons on the control panel. Once finished press the mode button until the screen reads “Auto”. By doing this you will not have to change programming.
@MikeyPipesOrlando
6 ай бұрын
Thanks for sharing
@Charbs20Ай бұрын
Does it matter which terminal the cables reconnect to?
@mattl6437 ай бұрын
Oooooohhh shut that pump down first buddy. 😂
@MikeyPipesOrlando
7 ай бұрын
Got him!
@glenrightmire18905 ай бұрын
Hate to be that guy, but it's a 5/8 deep socket, not an 11/16... also, if you don't breach the filter and let the system drain down you will get A LOT of water when you pull any plug/sensor from the heater. Drain filter by opening the air relief valve, wait 5 minutes Then take drain plug out of heater manifold. Once the heater drains you can replace what you need. DONT pull a plug or sensor when a pump running..
@MikeyPipesOrlando
5 ай бұрын
Thanks for sharing those tips & tricks.
@jimmy86537 ай бұрын
Tommy 2 pipes !
@MikeyPipesOrlando
7 ай бұрын
lol
@kennethbrandon14187 ай бұрын
Definition of punching your way out of a wet paper bag. Never double commented before
@MikeyPipesOrlando
7 ай бұрын
Thanks for sharing
@larrymicheletti45175 ай бұрын
I changed the ags and it still will not heat my front panel only shows service heater. The front panel will not light up. The only light is the service heater light. Any suggestions. Thanks
@MikeyPipesOrlando
5 ай бұрын
Bad panel?
@ZmuBMAC16002 ай бұрын
Mine won’t even turn on when I push the button? It worked last nite
@MikeyPipesOrlando
2 ай бұрын
Did you try opening the manual?
@kennethbrandon14187 ай бұрын
Guy, what are you getting into? Theses guys are using harbor freight tools? I had a girlfriend that went to pcb for vacation and never came back too?
@MikeyPipesOrlando
7 ай бұрын
Send her to Mikey Pipes
@dc90397 ай бұрын
I would have replaced that corroded terminal connection.
Пікірлер: 34
Hello 👋 Tom. Nice to Meet you. Keep up the Strong 💪 Efforts and Thanks for Helping make the Trades Great Again. 👍🙏
@tbofinger1
7 ай бұрын
Thank-you stayed tuned for more great content!
@MikeyPipesOrlando
7 ай бұрын
Thanks, you too!
I knew it was going to blow with pump on. 😂 job well done Tom
@MikeyPipesOrlando
7 ай бұрын
🙏
@scottmaz4063
7 ай бұрын
@@MikeyPipesOrlando guess he got a little bit jumpy with the camera now. He'll be alright
Happy New Year and thank you for all of the informative videos.
@MikeyPipesOrlando
7 ай бұрын
Happy new year!
Hi Tom Nice to meet you. Happy New Year.
@MikeyPipesOrlando
7 ай бұрын
Hi Scott. It’s me.
@tbofinger1
7 ай бұрын
Thank-you! Stayed tuned for more great content! Happy New Year 🎆
On the control panel there is a “Mode” button that has three functions as indicated in the box. Press the Mode button until the screen reads “Service”, your are now in Service Mode. Once in service mode you can manually control all your equipment, filter pump, heater etc via the buttons on the control panel. Once finished press the mode button until the screen reads “Auto”. By doing this you will not have to change programming.
@MikeyPipesOrlando
6 ай бұрын
Thanks for sharing
Does it matter which terminal the cables reconnect to?
Oooooohhh shut that pump down first buddy. 😂
@MikeyPipesOrlando
7 ай бұрын
Got him!
Hate to be that guy, but it's a 5/8 deep socket, not an 11/16... also, if you don't breach the filter and let the system drain down you will get A LOT of water when you pull any plug/sensor from the heater. Drain filter by opening the air relief valve, wait 5 minutes Then take drain plug out of heater manifold. Once the heater drains you can replace what you need. DONT pull a plug or sensor when a pump running..
@MikeyPipesOrlando
5 ай бұрын
Thanks for sharing those tips & tricks.
Tommy 2 pipes !
@MikeyPipesOrlando
7 ай бұрын
lol
Definition of punching your way out of a wet paper bag. Never double commented before
@MikeyPipesOrlando
7 ай бұрын
Thanks for sharing
I changed the ags and it still will not heat my front panel only shows service heater. The front panel will not light up. The only light is the service heater light. Any suggestions. Thanks
@MikeyPipesOrlando
5 ай бұрын
Bad panel?
Mine won’t even turn on when I push the button? It worked last nite
@MikeyPipesOrlando
2 ай бұрын
Did you try opening the manual?
Guy, what are you getting into? Theses guys are using harbor freight tools? I had a girlfriend that went to pcb for vacation and never came back too?
@MikeyPipesOrlando
7 ай бұрын
Send her to Mikey Pipes
I would have replaced that corroded terminal connection.
@MikeyPipesOrlando
7 ай бұрын
Thanks for sharing your feedback
🤣
@MikeyPipesOrlando
4 ай бұрын
hi
First comment
@MikeyPipesOrlando
7 ай бұрын
Champion