One last question for you. And I have to thank you sincerely. You have I recently bought a brand new xr1220 because everything I read made it seem like it was "sound board for dummies". lol. I have a yamaha mg board as well, and not being a sound engineer it proved just too complicated for my limited knowledge. This board seems like with a small learning curve it does alot of the more complicated adjustments for me, and seems almost fool proof. I'm sure if I knew more, I could improve upon

Great job Salute

I'm using the mixer's internal amps for monitors and have it set for the 2 gray sliders to turn the mains up and down as they're connected to a power amp coming from the mixer's XLR L-R outputs. With the mixer's amps set to MON-1 and MON-2, can the sub output still be turned on???

The only issue with this mixer is there's no EQ on the passive left/right xlr outputs on top of the mixer ..you'd have to bring an extra stand alone eq to notch out the bad frequencies ! ..Unless someone knows a work around !

am i able to connect this mixer to my laptop so i can record any/all the mics that are plugged into it using audacity? i am trying to record drums with a few drum mics and i cant afford to buy an interface or another mixing board but a friend of mine has this mixing board so i was wondering if there is a way i can make this work.

Hopefully one that can be mixed seperately from the mains and wedge monitors. I.E. Can the monitor 2 system on the individual channels be adjusted and mixed sperately and come out a line level output? Again, thank you sooooo much for the videos and advice. ( and as I go I may have more questions if you don't mind).

Oh yes, and the last, last, last question of the evening. lol. When setting up the auto eq function, we put the mic 10 ft from the speaker, but should it be faced twords the speaker or away from it as if it were in position to sing?

I'm glad you don't mind, because here I go again. lol. Does it retain the auto eq settings from use to use until I rerun the setup, or do you have to redo it each time you turn the unit on?

Ok, and one last last question for the day. lol. When I do the auto eq'ing, do I only want the vocal mics turned up/on, or do I want to turn on and provide the "nominal volume to others as well, like the mic's mic'ing the guitar and bass amps, and any drums?

how do u hook up speakers and monitors to this mixer?

So when your running 1 amp on left and right mains, and one amp on left and right monitors, you just run the auto eq on one speaker for each?

I am stiill curious about a couple things. 1. Can the RTA Autoi eq'ing be done with a condensor mic? Does the universal phantom power run through it? All I use is super cardiod condensors, is it better to use one of the mics we will actually be using to run the auto eq'ing? Also, you talked about doing the auto eq'ing on a left speaker and then a right. If you are running on amp to 2 mains, and one to 2 monitors, can you use the auto eq? If so where do you position the mic? Thanks.

The sound I am getting. But it is allowing me to be functional and far better than what I was accomplishing with my other board. But what I was going to ask was: I am running my mains off one internal amp, and a pair of wedge monitors off the other. I personally ( I'm the singer), and my drummer have wireless in ear monitors. What would be the best way to hook them up? What source should I use coming out of the board?

can you help me? I have the XR1212 was out running sound for a friends band had everything hooked up right plugged in my powered Subwoofer and had WAY too much bottom end tryed turning down the subwoofer itself no change I don't understand why there would be so much low end. I could not get a good sound.

I purchased a peavey xr1212 and have returned the mixer twice now to the supplier. The fans (internal cooling) on both accounts makes a noise that can only be described as not comfortable. Almost as though a bearind were displaced. Any answers before i give up.

Will this power mixer combined with Peavey PR 12 loudspeakers be enough to amplify a room of up to 500 people for lectures, and other speaking events?

connecting a Tascam recorder to the mixer TAPE OUT is not giving signal to the recorder. what can I do as I need to record while performing please.

@randywoolum2648

9 жыл бұрын

The TAPE OUT has no level control, and I found going through the HEADPHONE jack does pretty much the same thing as a TAPE OUT but DOES have a level control.

feedback problm