You do not need to mark the 2 pieces for "alignment". I know Raj has put that in his instructions but someone that has spoken with him in person has confirmed it is not necessary.

@50sKid

3 жыл бұрын

Yeah I didn’t think it was really necessary either as I didn’t see balance marks on the inner piston

@rockhoundalexander

10 ай бұрын

So one of the two vanos I took apart without marking The other one I have not taken apart yet I am understanding that this should not be a problem.

@akoyadunknow

9 ай бұрын

I'm currently doing the job and from what I can tell it does not matter. So long as it turns and purges to the lett you're good

@YourBuddyKeith

5 ай бұрын

It was likely suggested out of precaution.

Dude!! this is awesome!! the only other video i have seen anyone rebuilding this system was a guy who spent about an hour cleaning oil and didn't explain anything in a way that makes sense. I am super happy you did this. I have all my parts but the chains, and I feel really confident rebuilding the vanos now. Thank you Thank you!!

I'm knee deep into an E38/M62 restoration myself. Went and bought 2 more used vanos sprockets just in case I screwed up repacking the first set. Been stockpiling parts for that car all winter.

Thank you for this guide. It was perfect. I just completed this. I did manage to damage one of the silicone rings (at the bend). A few things that helped me with the Vanos rebuild: I stuffed a short piece of 1/4" rubber tubing under the washer which kept the piston extended and freed up my hand to work on the rings. I cut some pieces of 14 GA insulated wire and bent it into about 1" u-shapes which I used to hold the o-ring and silicone ring in place as I worked it into and around the groove. I filed the sides of my picks down which improved working them within the narrow slot. I also filed the sharp pick points slightly to reduce the risk of tearing the rings. I bent and filed a small paper clip to carefully pull up on the rings. Lastly I found I didn't need to fold the silicone ring but was able to work most of it into the groove and then carefully work the bottom of the ring with my thumb and the flat side of a small screwdriver to get it to go in.

Nice to see you still doing informative BMW videos. We all highly appreciate the amount of time, dedication, and effort you put into these videos! You and NathansDIY have helped me immensely with my BMW’s and sparked my hatred for them even more which is leading to me buying more of them 😆 Also, this is the best and most comprehensive guide on M62 VANOS on KZread. Congrats. Thank you for running through how easy it is to keep M62’s up and going

@edkalsbeek1765

3 жыл бұрын

Easy ???

Thank you for deciphering the convoluted instructions and crating this video. The combination of the obscure photo placement and diction on the website caused me to give up and just scroll through the photos alone. Using the term “extra” to describe the instructions is putting it lightly 🤣

Thanks 50sKid for adding this video. This is so much more involved than I could imagine. Nothing like the E46 duel vanos.

It's like he went away for a couple of years to a mountain in Cali listening to 50s music and had an epiphany: I will rebuild m62 chain guides and share it with my followers on utube. Then I will rebuild the entire engine. 🗻 🙏 🎸

15:20 "Guide it into the groove while you're putting it in. And that's the real key, that's the trick to this whole job. Remember to keep this piston up, like this, and we just start feeding it into the groove..... because that's the best way.... that I found to do this." LOL

Great video. Thanks for your efforts.

I remember a couple years ago vannos the youtuber talking about how his name that his dad was a mechanic and he heard vanos and though it was a cool name. Today I finally learned what he was probably talking about

Pretty Groovy man! Thanks for a great video!

I didn't even know they could be rebuilt. 😲 I just clean 'em and get them back in. Maybe it's time to start thinking like a 50's kid. 😉

Thanks for this videos,,,,,just by watching you're videos ,,,,I feel like I did this several times....thanks,,,,,keep it coming......👍👏👏👏👏👏👏

This guy is just a good instructor. Thanks dude. My 540I/6 needs this job. Its either i pay 5k or do this job myself.

Fearless! Next level stuff 👍😎

You should replace those o-rings. Not because they are bad, we just want to see more of your videos :)

@50sKid

3 жыл бұрын

I mentioned it. I didn't need to do it because it was warm in my shop.

@RCNITROPRODRIVERS

Жыл бұрын

@@50sKid I just did the vanos rebuild on my 2000 540 6spd last sept noisy vanos and sluggish below 3k rpm. Did it with your videos and also skipped the distribution block and it’s seals as that is for pre99/09 cars. went alright, noise was gone but still slow on the low end, now after winter I decided to replace vanos solenoid check valves with hopes of improvement and when undoing bank 2 solenoid 10mm of the threads on the distribution block snapped off and came out with the solenoid ruining the distr block So I now have to do this all again! BUT LOW AND BEHOLD! Just made clear that my car was made 99/07 200k miles witch makes sense why it was still sluggish if I did not fix those seals Now I’ll just get the coated housings and do all guides and remaining seals and finally get to enjoy the torque it’s supposed to have It actually feels good just to have figured my problem out even tho I could have prevented doing it all all over again

Thanks for making all these great videos! 👍

@50sKid

3 жыл бұрын

Glad you like them!

@michaelblacktree

3 жыл бұрын

Dude, if it weren't for your videos, my car would probably be in a scrap heap. No joke.

glad to see your still doing shit on bmw's! i havent been here since my e46 era. wish u luck!

Great video

Damn. Just Damn. Impressive.

50's Kid....., LOL..., I feel that all of the crook mechanics will hate you for this film big time yet we love ya now all the more and there is MORE of us LOL!!! awesome vid and your work foremost :)

Hey man good to see you again. Do you have an video of e46 m54 steering angle sensor diy?

Any concern with the Teflon seal getting pushed down/ unseated when pushing the piston back in? Just got mine pushed in and wondering if I should take it back out to confirm it’s still seated or just run it.

I’m looking at getting the vanos rebuilt on my X5 4.4. They are making a knocking noise (all my research leads me to believe that’s the cause anyway) when the engine gets warm. I’m tempted to do the job myself but I need to get the GAS timing tool as I don’t fancy using the China tool.. Did this help make the engine run really quiet?

My time has come

If you know what the relationship is between the two marks on the vanos gear?

One video showed that leting The vanos seals float in boiling water for some minutes makes them easyer to install.

Hey 50 s kid my e46 got code for p1083 , my pcv house cracked and I slide a large hose that snug in and held the line in place didn’t notice any leaks besides oil around the area . I’m guessing that why my car throws on that code ? I have replaced top intake boot and lower one looks okay 👌 no tears. Any advice would be helpful thanks 😊

Hi sir yes this repair will fix diesel sound at idle for sure ! But will not fix rattle noise on start up . I did every think to try fix rattle on start up with no good Result. I'm still Chasing this problem :\

@alexanderstevens145

2 жыл бұрын

How did you go? I have same issue

@alekjuskevice

Жыл бұрын

Do you have a good oil filter, with a check valve in it? It sounds like your oil pressure drains back when it sits. Use a Mahle, Bosch or like, not Phram

is the VANOS rebuild a "one-time" fix, as we are permanently deforming the timing wheel? In other words, can I redo this entire procedure after it already had it done before? Much appreciated.

Do you to take everything appart to do the vanos rebuild only? Or is it just sufficient to pull the top timing covers only?

@mike325ci

2 жыл бұрын

Just the upper timing cover will give you sufficient access to the vanos units if that's all you are doing - no need to remove the lower timing cover (which requires removal of A LOT more things and accessories attached to block). He is doing it along with the whole timing chain and guide job, and doing the VANOS rebuild since he's "already in there."

Brave man, that's all I can say. . . couldn't pay me a million bucks to do this

Hey 50’s kid. Love your videos. I rebuilt my n42 following your n46 instructions a while back. I’m wondering if there is a kit to rebuild the vanos on the n62 and if it is worth doing while I replace guides and valve stem seals? I’m getting codes for exhaust camshaft position sensors on bank one and two bit have replaced all four sensors. Also I replaced eccentric shaft sensors, crankshaft sensor and vanos seals. Car is misfiring and only wants to start when cold. I’m being told timing has likely jumped by people in the forums so I will have to go back in and look.

@LynxStarAuto

Жыл бұрын

The VANOS on N62's are not as problematic. On those what fails most is the solenoids. It has 4 of them (one for each sprocket), and they are super easy to replace, but pricey. Easiest test you can do is swap them around and see if the fault follows the solenoid.

@preachercharleshadeniii3764

Жыл бұрын

@@LynxStarAuto Will a bad VANOS let the CAM turn and cause the car jump out of time? The VANOS CAM on the passenger's side jumps ahead of the other CAM while the CAMs on the driver's side stay in time with each other.

Omg TEDIUS AF!!!

Is it possible to do this vanos rebuild with out taking the lower cover off

@LynxStarAuto

Жыл бұрын

Yes. But you need to support the chain with the gears out.

Hey 50skid. I need some big help from you. Is there a way to message you directly? I messed up big time on my car Thanks

@benjaminkaric2874

11 ай бұрын

What did u do? And did you fix it ?😅

Jason do you like the Chinese style eggplant recipe? 😄 @50skid

@50sKid

3 жыл бұрын

Oops lol

M62 TU rattle will come back sooner or later , it will not work, only new unit. Know from past.

@abautomotive2886

26 күн бұрын

I have the same impression of trying to do this. After all that "massaging," warping, and bending of the Teflon seal, how will that work better than even the old one? How long will it last? This doesn't look like the right repair method that I could guarantee.

Yeeah

Or you just buy them already rebuilt from DrVanos!

First!!!

Nm. Just sayin’.

The gasket wasn’t fine. I made the same mistake. It’s already compressed and needs replacing.