Ty very much,great video fantastic explanation pure 10! 🙏

As an electronic engineer i have to say that this is a great video of how to do it and fix the problem. I saw one other video posted by some idiot who tells you that to fix this same problem is to add more solder to existing power transistors. LOl like that will fix the problem, imagine him working on electronics. My neighbors tv broke down and poor lady was going to throw it away but I said "no way lets see what the 8 blinks are telling me" and the rest is history. Must replace the PCB screws with new one that you get in a kit.

Thanks for the parts and the video. I accidentally pulled pad 5 off the board for component ic152. Is that pad just an anchor or do I need to expose some copper around it to solder to?

Hello, great video thank you!...So I have a Panasonic TC-P55VT30 which was showing 7 blinking lights, when I disconnected SC board it went to 8 blinks, then i plugged the SC board back in and disconnected SS board and it went back to 7 blinks. Any thoughts on which board is shot? Thank you for any help!

can you recommend a soldering kit that comes with all the tools necessary to install this kit?

Hello, I bought this repair kit removed the old parts not thinking I removed the new ones from the Q051 bag and D041 bag at the same time now I am unsure where they go. 1 has RF2001 the other has DG302. Could you inform me what spot on the board they go? Thank you

I bought the repair kit from you but I don't have a heat gun like I see in this video. How can I solder the middle of the IC chip with a standard soldering iron? Also, one of the ever so small printed circuit board legs broke off while removal of the same chip. I will try to solder it back on along with the chip. The tools you're using make this repair look so much easier. I still have hope to get the job done. I await your reply on soldering the middle of the chip. Thanks rb67mustang.

Hi, I have a TC-50PU54 that does not power on and blinks 8 times. I work in an SMT shop so board repair would be a snap. Should I just order the repair kit or is there some troubleshooting I should do first? Thanks!

Make sure to test every RF1501 components with around 41 ohm on the 200k caliber on the SS board and SC board because it might the whole plasma screen that grills thoses chips

I have a TC-P50U50 and I just installed all the parts from ShopJimmy. Installed the resistor, IC, voltage regulators and new screws. Finished the repair, started the TV and about 15 seconds afterwards it smelled of burning and the tv shut itself off. Help?

panasonic tc-P50u50 is black and blinking 14 times. Should all the 250v2.2uF capacitors have resistance at all times?

Hi there can you help I have a Panasonic TH-P60S602 blinking 7 times on start up, not start up. can you hlep with parts needed? Thank you

Need help with a tc-p55vt50 its blinking 6 times

Hi, I have got similar problem of 8 blinks on my Panasonic TH-50PZ80B model. Any help to solve this issue please ?

Hello, I have a Panasonic TC-P60ST50. The indicator light blinks three times. I have researched this and found..Three Blinks: Three blinks of the power LED indicates an over-current or over-voltage condition in one of the DC supplies of the AP board. The AP board is repairable. Therefore the use of an ohmmeter and peak-hold-voltmeter is required to determine the cause of the shutdown. An over-voltage condition is definitely a defect of the AP board. An over-current condition may be due to a short circuit located in the AP board, A board, or the LCD panel. Do you have a video that details this repair?

Any suggestions for those of us who do not want to spend $500 on a preheater?

Can i send my TNPA5623 board and you install the components. my soildering is a bit rusty. I have the p50ut50 tv

Can you provide the part numbers for parts D041 and Q051?

can I do this without the preheater?

hi..have a philips 50pfp5332d/37 plasma..that is completely dead..no standby light..no clicking no nothing..trying to locate stndby power board?? if there is such a thing because im thinking if I don't at least have stndby power there wont be power on power..power in is 120v...after that I don't know where to go...any suggestions???

hello. my tv is Panasonic TX P55VT50E. when shown white pictures tv starts to buzz. the whiter the picture is, louder the buzz is. tv was already on service and they changed one bord. after a approx. one year of use, tv starts to buzz again. what board do i have to replace?

Panasonic TC-P50U50. I replaced the components on the TNPA5623AB board and the 8 blink code went away. However, now the TV turns on but has a black screen that flickers and will not respond. Any Ideas?

My Insignia NS-LTDVD26_09 WILL NOT TURN ON USING THE POWER BUTTON. AFTER SEVERAL TRYS WITH A RADIO SHACK 15_302 REMOTE RANDOM CODE INPUTS SOMETIME TURNS IT ON..IT WILL ALLOW ME TO VIEW DVD'S WITHOUT BASIC OPTION EXCEPT VOLUME WORK FINE. THE RED POWER ON LIGHT WILL COME ON AFTER I UNPLUG IT SEVERAL TIMES..THEN I ENTER SEVERAL CODES UNTIL IT POWERS ON. SHOULD I REPLACE THE POWER BOARD? Forgot sometimes it holds the code and I can power it on and off several time before it goes back to the graveyard sleep. Thank you for any feed back james

I purchased the SS Board Component Repair Kit from SJ but I messed up one of the pads on the IC (pin 4). I believe this is a ground but would like to verify this by checking the schematic/pinout for this IC (BD8694 1521). Can you provide a datasheet for this chip or a mfr/part number?

I have FILIPS 42PF9966. hard turns in the morning when it is cool. When you turn it on after 10 to 20 attempts red light flashes me one and 8 times in succession. If you turn it off while hot and turn it on again, then fell without problems immediately. I do not know what the problem is, so please help me. Thank you.

hola; tengo un panasonic th-pd60u cuando lo enciendo palpadea 8 veces (8 blinks) y no enciende. quiero saber que pieza debo cambiar para repararlo. espero por ustedes, gracias nota; favor de escribirme en español

Hi ... I have Panasonic TV model TC-P65P1 ... the red light is blinking 8 time. Please let me know How I can repair it? Thanks in advance.

Hi, I'm trying to find out why a Sharp AQUOS LCD TV turns off unexpectedly after one minute on. I have to disconnect it for two to three minutes, reconnect it to the power outlet and then you can turn it on. It only stay on for one or two minutes and the it turns off by itself. The model is a LC-42SB48UT. And no, there's no Firmware upgrade for it.

Hi, I have a Panasonic TC-P55UT50 that blinks 8 times when powered on. I have had the SS board repaired, but it still blinks 8 times after being reinstalled. I have disconnected the SS board from the power supply and now it gives the error code of 6 blinks when turned on. Does this mean that something else is wrong?

I have a Panasonic Plasma TC50XT50 and it has no power. I checked the blink code and she blinks 3 times. I checked the codes and it says that the D board 3.3 volts is the problem. I looked all over the internet to find a D board with no luck. I do believe it went out after a lightning storm. Any help will be appreciated.............

I have Panasonic TC-P50U50 and it blinks 8 times. Just went black. I have opened it up and checked R16051 5.6 oh res and mine is 6.2 on SS board. What do you think?

I bought a 37' Proscan lcd tv and as soon as I brought It home I realized that there is one kind of like shaded line across the screen..and I was wondering if there was a way to fix it

@user-wr8vz6rn5q

9 жыл бұрын

Wow I think I just found the problem.. i was looking through the slits in the back of the tv (vent slits maybe) and the board with all the bright lighted circle.. I have notice that were my problem is on the screen is where there is a small wire blocking the hole, but now that I think about it its on the back of the tv so its probably not that right?

TV model TC-P65ST60 TV wouldn't turn on and had 7 blinking lights. I removed cover, disconnected the Yboard and plugged back in. TV then had 8 blinking lights. thanks

@shopjimmy

8 жыл бұрын

+Keith Dougherty Try all repairs and troubleshooting at your own risk. Repeat the same test on the SS board. Thanks! www.shopjimmy.com

HI i have a tc-p50u50 .. i turn it on but it shuts right off and blinks 8 times can u help with a kit i can buy from yall to repair it

@1204timyr

9 жыл бұрын

+michaelclearman clear man the instructions and parts are in te description of the video. i'll try to buy a entire new board because i don't have the tools to solder

Thanks for the video. I have a Panasonic th-p50st30a Plasma that just died. I started receving the 7 blinks error. Upon investigation to confirm the SC board was the issue. I unplugged the SC board and powered on and then got an 8 blink error code which indicates the SS board is the issue. Have you experienced anything like this and do you have any advice on what steps to take to repair? Thank you.

@dutchkork

7 жыл бұрын

Hey I got the same thing...did you figure out if it was your SS board for sure? If so, how? Thanks!

@kaneelias

7 жыл бұрын

dutchkork I figured out it was the SC board. I got a refurbishment replacement chucked that in and now good as new

Valor de los componentes de este kit por favor

I have a Panasonic TC-P50S1 plasma. The power randomly shuts off and I'm getting the 8-blink code. Do you have a repair kit for this model? Or, maybe even better for me, would be a new SS-Board. It would probably be easier for me to replace. Thanks!

@shopjimmy

9 жыл бұрын

Guyman Murphree Try this at your own risk. Unplug the TV, then disconnect the SC board and plug in the TV to see if the TV powers up. Reply with the results of this test. Thanks! www.shopjimmy.com

There seem to be missing the information what causes this problem. It's described in the technical bulletin TB-13-02 from Panasonic. When the board is just reassembled without cleaning the areas affected by the arcing it will be damaged again as I learned the hard way.

@tomtechtod9200

9 жыл бұрын

It can be found here: www.avsforum.com/forum/attachment.php?attachmentid=76207

@i5usko

8 жыл бұрын

+TomTechTod I repaired the board and it died less than a second after power on. Did you just sand the traces that showed signs of arcing? Could you explain further on what caused the problem and how you fixed it? Is it from the board grounding out at the screw hole or is it supposed to ground there and it has a poor connection?

@i5usko

8 жыл бұрын

+i5usko It looks like it was a bad ground. Too bad I wasted $20 before I read your post. Really these parts should only cost a few cents.

@ThePHILALLENSHOW

8 жыл бұрын

+i5usko TV repair made easy?lol what do you think anyways that's what sj says

@tomtechtod9200

8 жыл бұрын

i5usko Only saw your post now. Yes the chassis is part of the ground even though there is a ground trace on the board, but my guess is it's impedance is to high so some current goes through the chassis. Just sanding may not be enough, it started sparking after only a few weeks. Then after using dented washers the problem was solved.

Have a Panasonic TC-54PS14 that will not power on but is giving an 8 blink code. Not sure if this helps but disconnected power and ribbons from SS and it gives me another blink code of 6 blinks. Does that mean I have other bad components as well?

@shopjimmy

9 жыл бұрын

Omar Torres I recommend that you bring your TV to a certified Panasonic Repair Shop. Thanks! www.shopjimmy.com

Hi frinds Paroblam are negetive pichure on Panasonic plasma thp60s60d Plese help me

I have a panasonic tcp50g15 plasma tv. Today I turned it on and the backlight turned on, but there is just a black screen. The red light is on and there is no flashing. The tv will not respond to any of the buttons on the remote or the tv itself. The tv will turn on and back on again 20 seconds after hitting the power button on the tv. It worked this morning and I have tried different HDMI devices, but nothing works.

Panasonic TX-P50S20E blinking 7 times.. what i have to do!!! Thank you very much for the opportunity to address

th-p42c10 blanking 8 times ...i need help pleas

I have Panasonic tc50pu54 and blinks 8 times, and the model for sc board is( Panasonic SC Y-Sustain TNPA5621AB TXNSC1SDUU for TC-50PU54) do you think replacing this part will fix the problem, and if yes do you have it in stock

@shopjimmy

9 жыл бұрын

Ramzi Khoury I recommend that you bring your TV to a certified Panasonic repair shop. Thanks! www.shopjimmy.com

👌👌👌

I don't know how to solder where I can I buy the whole board or where can I get it fix?

@shopjimmy

9 жыл бұрын

Jonadab Debe Try all repairs and troubleshooting at your own risk. What board needs repair? Thanks! www.shopjimmy.com

@JonadabDebe

9 жыл бұрын

ShopJimmy.com the TNPA5623 ss for the Panasonic TC-50PU54. I did all the tests but I don't how to solder.

@shopjimmy

9 жыл бұрын

Jonadab Debe Try all repairs and troubleshooting at your own risk. You can sign up on our website to be notified when the board is back in stock. Otherwise, I am not sure where you can find the whole board. Thanks! www.shopjimmy.com

TC- p55ut50 Panasonic vista smart plasma TV Powers up for a second then turns off and gives me a blinking red light total of eight blinking red lights Someone please help

I replaced all parts with your kit and then noticed component PC251 is missing from the board, looks like it broke off. Can you tell me what this component is?

@shopjimmy

8 жыл бұрын

+London Harroff Try all repairs and troubleshooting at your own risk. Can you upload an image of the location on the board? Thanks! www.shopjimmy.com

@londonharroff3281

8 жыл бұрын

I can't upload an image, the component that is missing is next to IC152 that is included in your repair kit.

@londonharroff3281

8 жыл бұрын

This is on the TNPA5623 SS board component PC251.

hai sir,my tv panasonic thp42x30k wont turn on...can you help me how to fix.

@shopjimmy

8 жыл бұрын

+Jack Sparow Try all repairs and troubleshooting at your own risk. Do you have a standby light in the front? Thanks! www.shopjimmy.com

@jacksparow7290

8 жыл бұрын

thp42x30k my panasonic plasma tv wont turn on ... because lightning

Panasonic plasma TH-42PV 60H SS board Rjp 3053 barning sir

@shopjimmy

9 жыл бұрын

Shaik Abdulla PLEASE SUBSCRIBE TO OUR CHANNEL - Try all repairs and troubleshooting at your own risk. Please reply with more details about the problems and symptoms that your TV is showing. Thanks! www.shopjimmy.com

Panasonic Plasma after trying to turn on it turns off almost immediatly with 8 red blinks. model is TH-P60st60A

Panasonic model TH42PX6U SN:LA62370579. Original starting problem was very Thin lines red,blue,and green line in the middle of the screen. The Video and Sound were Ok. After watching some of your videos, I cleaned the ribbon cables on the bottom buffer boards and reseated them all into their sockets. Still same result. I then Purchase the left buffer bd. TMP A3812. After installing this board. Now I'm having vertical line clear across the screen with video, only on the first 10 inches of the left screen; Vertical lines through the rest of the screen, sound is Ok. Re-install the original bd and still got this new problem. As of now I have also replaced the right side buffer bd TMP A3813 an the drive bd TMP a 3810. No result the New problem is still there. Can you please advice if this is due to another board. Thank you very much for your support and advice. Respectfully yours. Didi

@shopjimmy

9 жыл бұрын

Diana Sepulveda This sounds like a TV panel (TV Screen) problem. If your TV panel is bad, it may be more cost-effective to replace the TV as panels are typically hard to find in stock, difficult to replace, and expensive. Thanks and please let us know if you have any further questions! www.shopjimmy.com

Panasonic TC-P54vt25 Wont turn on. 8 blinks.

@shopjimmy

8 жыл бұрын

+Skip K Try this at your own risk. Unplug the TV, then disconnect the SC board and plug in the TV to see if the TV powers up. Note that it will not have a picture on the screen. Reply with the results of this test. Thanks! www.shopjimmy.com

tvpanasonic 58" dead no power

@shopjimmy

9 жыл бұрын

jean william Try all repairs and troubleshooting at your own risk. Do you have a standby light or anything blinking in the front? Thanks! www.shopjimmy.com

Replace the whole board

@HighCompressionII

8 жыл бұрын

+Rick Clark Very Poor practice to 'just replace the board, hints of you unable to proper fault-find to component level.! --'board changers' are NOT technicians IMHO. Fit a used board with old parts, and who knows how many thousand hours on it, you could well be back to square one in a short while, and there's one less board for a set that really does need it, instead of just a simple fix on this one. This attitude has lead to the very short supply and stupid prices of boards such as TNPA5105, TNPA5081 etc... --Some of these in Dead condition change hands for $50 upwards..... Another reason NOT just to replace--There are SO many revisions of these things, its doubtful you'll get the exact one unless you order from Panasonic.--With their prices--Who does that!

I Don't think many diys can do this.WHO HAS A HOT AIR TOOL. only tv shops might. this seems like a video for techs not DIYS.This board is NOT AVAILABLE.good luck finding it.

@shopjimmy

9 жыл бұрын

ThePHILALLENSHOW Thanks for your input, and we are happy to provide these videos to both techs and DIY'ers. As we mention in the video, "The tools used in the video are recommended for the repair, but each person may use different tools according to their skill level and preference." If the board itself is difficult to find, the repair kit can be a great solution for repairing your existing board, if the symptoms are a match. Thanks! www.shopjimmy.com

Bought your overpriced repair kit. Did the repair. Tv worked less than a second, made a pop noise, and now it's back to 8 blinks.

@shopjimmy

8 жыл бұрын

+i5usko Try all repairs and troubleshooting at your own risk. What kit did you purchase? What was your original symptom? What is your TV model number? What is your part number? Thanks! www.shopjimmy.com

@i5usko

8 жыл бұрын

+ShopJimmy.com sj-TXNSS1SDUU Repair Kit, I have a t55ut50. This was the issue and if you read just a few posts down you will see that this is caused by a poor ground. If this problem is not fixed then the board will just fail again. This was not mentioned in your vid at all so, I assumed it was caused by a short circuit on one of the components(namely that little resistor). The repair worked until the underlining issue caused failure again. Only reason I order from you was because of the video showing what components were damaged. The fact is the video doesn't tell you what caused the failure and now I'm out $20 because of it. If I had known this beforehand I would have a tv again.

@shopjimmy

8 жыл бұрын

+i5usko What were the original problems/symptoms that your TV was showing, before you installed the repair kit? Thanks! www.shopjimmy.com

@i5usko

8 жыл бұрын

+ShopJimmy.com 8 blinks what else?

@shopjimmy

8 жыл бұрын

+i5usko Thank you! Did you install the screws that came with the repair kit? Thanks! www.shopjimmy.com