Painting Skateboard Trucks
Спорт
Mr.Tegni Skateboarding Germany
Painting skateboard trucks
Step by Step Instruction
Hier zeige ich euch wie ich mir die trucks farblich umgestaltet habe.
Hier das passende Deck
• SK8board Spray Paint B...
Lackieren mit der Sprühdosen
Das Material zum lackieren vorbereiten.
In diesem Fall die Achsen, Trucks.
1.
Vorreinigen.
Den groben Dreck, Schmutz entfernen, wenn vorhanden.
2.
Schleifen.
Beziehungsweise anschleifen.
Flächen mit Schleifpapier bearbeiten.
Tipp:
Es gilt, je feiner das Schleifpapier um so glatter ist die Fläche nachdem schleifen.
3.
Material reinigen.
Fläche richtig reinigen! Entstauben und entfetten.
4.
Abkleben.
Flächen die nicht mit Farbe beschichtet werden sollen, gut abkleben.
5.
Lackieren, Sprühen.
Zweimal die Fläche lackieren, die erste Lage Farbe
10 bis 20 Minuten trocken lassen, dann wiederholen.
Für ein richtig gutes Ergebnis, nicht zu viel Farbe auf eine Stelle sprühen, sonst verläuft die Farbe und es gibt Tropfen oder Läufer.
Tipp:
Darauf achten, dass erst die Sprühdose bewegt wird und während der Bewegung der Sprühknopf gedrückt wird.
Fließende bewegungen mit den Sprühdosen ausführen.
6.
Teile, Fläche 24 Sunden trocken lassen.
Fertig.
Viel spass
Painting with spray cans Prepare the material for painting. In this case the axles, trucks.
1. pre-clean. Remove the coarse dirt, dirt, if present.
2. Grind. Or grind. Treat surfaces with sandpaper. Tip: The rule is, the finer the sandpaper, the smoother the surface after sanding.
3. clean material. Clean the surface properly! Dust and degrease.
4. masking. Mask off surfaces that are not to be coated with paint.
5. Varnishing, spraying. Paint the surface twice, the first layer of paint Let dry 10 to 20 minutes, then repeat. For a really good result, do not spray too much paint on one spot, otherwise the paint will run and there will be drips or runs. Tip: Make sure that the spray can is moved first and that the spray button is pressed during the movement. Perform flowing movements with the spray cans.
6. Allow parts, surface to dry for 24 hours. Ready.
Have fun
Mr.Tegni
Пікірлер: 15
Thanks for making this. This was 100% what I was hoping to find. Great job and the trucks look great.
@MrTegni
Жыл бұрын
Glad I could help
Why did you paint the pivot cups instead of removing them?
@MrTegni
Жыл бұрын
Hello. it is not absolutely necessary to remove them. they can stay in but also out. I left her in there.
Hey i've been looking into spray painting my trucks but i have a couple questions. Is it completely necessary to sand my trunks? They're default chrome and have no paint but am i supposed to still sand them? Also, do i need a primer, or can i get away with not using it?
@MrTegni
2 жыл бұрын
It depends on how good you want the result to be. In principle, an adhesion grung is recommended, which is a kind of pre-layer So that the paint adheres better to the chrome surface. So degrease the trucks, sand them finely, apply a precoat, Let the primer dry, apply paint 2x and finish with 1x clear coat. If it's supposed to be cheap and you drive a lot, it's enough to sand the trucks once, degrease them, paint them twice, done.
Thanks for tutorial! Can I use varnish after painting? I have matte paint, but I want trucks to be glossy
@MrTegni
10 ай бұрын
sure, of course
If the trucks are brand new, you can just spray paint them right away right? I Want to get ace trucks in black 7.75 but my skate shop only got silver ones. Also what spray paint should I use?
@MrTegni
11 ай бұрын
hi. you need paint for metal and don't forget to sand the trucks properly. for an even better result use a metal primer. much luck
What kind of primer do you use??
@MrTegni
2 жыл бұрын
Hello For the project I 2-component epoxy resin primer used for metal.
What spray paint? Or just metal spray paint
@MrTegni
Жыл бұрын
Hello. i have use metal spray paint.
Painting with spray cans Prepare the material for painting. In this case the axles, trucks. 1. pre-clean. Remove the coarse dirt, dirt, if present. 2. Grind. Or grind. Treat surfaces with sandpaper. Tip: The rule is, the finer the sandpaper, the smoother the surface after sanding. 3. clean material. Clean the surface properly! Dust and degrease. 4. masking. Mask off surfaces that are not to be coated with paint. 5. Varnishing, spraying. Paint the surface twice, the first layer of paint Let dry 10 to 20 minutes, then repeat. For a really good result, do not spray too much paint on one spot, otherwise the paint will run and there will be drips or runs. Tip: Make sure that the spray can is moved first and that the spray button is pressed during the movement. Perform flowing movements with the spray cans. 6. Allow parts, surface to dry for 24 hours. Ready. Have fun Mr.Tegni