I second the drywall plumbing project video. Thank you helping all of the DIYers who could never afford hiring a plumber for these projects.

I watched 4 videos before I got to yours. Wish I had found it first. Exactly my issue and you made it look super simple. Great step-by-step instructions. Thanks!

Hi Scott. Very nice step-by-step video! I have 2 suggestions: yes, while you spoke about deburing the outside of the pipe, it is also important to debur the inside of the pipe to stop water turbulence and possible banging from all of those burrs especially when cutting with a hacksaw. Secondly, I would put a pipe clamp on the 2x4 just before the SharkBite to give the whole assembly more support. Yes, I would interested in the drywall plumbing project too! Thanks!

Recently I was informed to change these to stop the leaks but didn’t know how to. Thanks for showing this will follow these steps. Will love to see other types as well. Just subbed.

I've been looking for replacing my garden faucet for quite some time and your video and the detail of step by step are very helpful. Thank you for sharing!

Love your videos.. great for home owners uses. And yes, you should include deburing and also a marked measurement of the fitting 15/16” so proper seating is achieved. Thanks for sharing your knowledge and information so handy guys could help themselves

Good video. I've used these on two spigots and both failed. They didn't fail on the pipe connection but on the outside at the chrome cap (vacuum break) on the top. You mentioned here what I didn't know at the time and that is you MUST disconnect your hose before they freeze. If I had read the directions (my bad) I would have realized this and saved myself the time and hassle of having to replace them.

I saw your video and ordered the parts and replaced the spigot on my own!! I am not a plumber but I do try to make a go at things and this was so simple to do..Thanks!!

Thank you. I just installed a new spigot on a wall that didn’t have one based on your video (and a few others). Works great and no leaks! 👍

Thanks very much for making this video. I reviewed it before I did the same job on my house. My only comment is that I assume you were concerned about orientation of the outside spigot because of the way it has to fit on your siding boards. Those who don’t have that issue should know that once the spigot and piping is installed in the SharkBite fittings - it can be rotated 360 degrees before securing it to the house.

Really appreciate the video and comments! Heading out do the replacement shortly

Going to replace my older 2 spigots with Sharkbite fittings as well as shut off valves for each! Thanks for helping us DIYer's!

Excellent, simple, direct, less talking is appreciated

Thank you thank you thank you! I am a senior widow in the woods so to speak and your video was so informative and educational . I hesitate to call plumbers unless in an emergency because of the expense as I am on SS . I would like to know more about those Shark Bite copper fittings .

Thanks for the video. I bought everything the same and everything works perfectly. I drilled my hole slightly lower to clear the lip on the siding so it sits more flush.

Over the years I have decided that if it's outdoors or wet areas I use stainless steel bolts / fasteners. Yes they cost more, but they save so many headaches down the road.

Yes, I'm interested in seeing the hard to reach spigots. It sounds like a good thing to learn.

@Chitown388

Жыл бұрын

Same here, I'd be interested in seeing the handling of that hard to reach spigots.

I'm surprised you didn't add a SharkBite shutoff valve, you if you ever have any problems with the outdoor faucet, you can just shut the water off to that particular faucet. Great Video.. Thank you. JC

My pipe burst recently due to the winter and we were able to hear the water leaking into the crawl space. Luckily caught it in time. Loved the video,without you I wouldn’t have been able to fix it!Also it was the weekend so it was hard to get ahold of a plumber!

@EverydayHomeRepairs

Жыл бұрын

Nice, way to jump on the problem, get it fixed, and avoid a bigger problem 👊

Great video! I just replaced mine the exact same way. I wish I saw your video sooner, it would have saved me some time.

Yes I would be interested in seeing the other spigots!

Thanks! This is exactly what I needed to replace my outdoor spigot.

Thanks for the video, by watching it, I realized I needed some stuff like the weather caulking and sandpaper.

Yes, absolutely interested in the other spigots. Mainly for tracing the line & finding it on the interior side.

Amazing job on this - exactly what I needed for very similar project.

Good video as always. I just replaced 2 frost-proof faucets this weekend. One leaked inside the house when you turned the water on. (Luckily I went into the basement right after turning it on or my basement would have flooded). And my other frost-proof faucet was spraying water outside when you turned it on. The anti-siphon had failed. I replaced them both with an Aquor V2+. A very slick system and they are rebuildable. Definitely worth checking them out. I have brick at both faucets and the recommend the Aquor V1 for brick or concrete but I liked the look of the V2 better and don’t mind the extra work. And I used the Pex-A expansion version with a service loop so I can pull it out from the front to service it should I ever need to. I personally don’t care much for the quick connect fittings. If I am in a tight spot or don’t have room for a torch to solder and don’t have Pex-A available I use a double ended compression fitting (or make one). It’s more work but I’ve never had one leak and I can easily take it apart if I need to service the hydrant.

I have a manufactured home that has all PEX plumbing and I always use the Sharkbite system. I absolutely love it because its so simple ands easy to use.

@Peterpiperofthes

2 жыл бұрын

Can't beat it, takes alot of work away from plumbers tho🤫

@MrPink2024

2 жыл бұрын

*The world could always use more bartenders.* 🤷🏾‍♀️

@joshcowart2446

2 жыл бұрын

What are you talking about. Why would we quit the plumbing when there’s all that work repairing failed shark bites

Great informative video. Thanks . As you said every situation is a little bit different, so I'd love to see some other scenarios for replacing a frost free faucet.

I live in Springfield,IL and I forgot to unhook the hose one winter and the next spring I had a flood in the basement when I turned on the hose to water the grass. I'll never forget to do that again! I had a plumber give me an estimate on replacing the spigot, he quoted me $700.00 and that's with a 10% discount!! I just finished doing the job myself with your help from this video and I did it for less than $100.00 and it only took a couple of hours. I can't thank you enough for your help and guidance! I'm a life long member of KZread University!!

@EverydayHomeRepairs

3 ай бұрын

Happy to help 👍

We have textured walls in our house on a slab, so that other video sounds very useful!

I have to replace my outdoor spigot also, but it is a the bottom of the list. It leaks so much outside, sometimes we can't tell if the water is on/off. Eventually, it all drains, but water outside is an enemy in the North. Mine goes inside to a finished part of the basement, but I may have access. I will have to add some of these details for when I'm ready to tackle. Thanks for the perfect pace of your videos.

Very good explanation of how to replace an outdoor faucet. Another brand of faucet I would like to see how you install is the Aquor House Hydrant. This faucet self drains and can be left uncovered during freezing conditions without bursting and would be interesting to see how easy it is to install.

@mattr3194

2 жыл бұрын

I just replaced all mine with the Aquor, you can put a SharkBite fitting on the end of the Aquor and then its identical install to this video. The vacuum breaker is on the removable hose part so it leaves a really classy fixture on the outside of the house.

Thanks, I'm confident that I can do this because of your step by step video!

I don’t mean to nitpick but you did miss one important step and a lot of people don’t do this step but it’s extremely important. That is measuring and marking the insertion depth on the copper pipe for the shark bite fitting. I think it’s 15/16 for half inch fittings and one in the eighth for three-quarter but verify those. It’s important because you can push the fitting on until it pops and stops and think you’re at hey solid seat but not actually be there. I marked the pipe once and push the sitting on and it popped and stopped. I looked at the mark I had made to ensure proper insertion depth and it wasn’t all the way on so I pushed harder and then it did go to the Mark for a solid seat. So that convince me that marking the pipe first prior to pushing the shark bite fitting on is extremely important to avoid leaks.

@EverydayHomeRepairs

3 жыл бұрын

Hey Steve, thanks for the comment and call out as you are right and I did miss calling out the depth during the final install. Take care!

@Toyotajunkie

2 жыл бұрын

It isn't nitpicking if you provide constructive criticism in a positive respectful manner, as you did here. Thanks for adding that important tidbit!!

@DireNeeds

2 жыл бұрын

There's actually a tool put out by Sharkbite that will deburr and measure the insertion depth for you. Handy thing to have.

@mtsflorida

2 жыл бұрын

@@DireNeeds yes I have the orange tool that measures and deburrs the outer side but you also need the pen with blades tool for the inside. Both are only about $30 all together at a building store

@eternalklothgardengangsta685

2 жыл бұрын

Very important, makes it full proof

I like to use a small spirit level on the pipe to the valve to insure you have downward drainage when you turn the valve off. Doesn't take much, half a bubble at the line will do.

Awesome I just took look because I need to replace on in my crawl space THANK YOU 🙏

This is my favorite DIY channel. Thanks.

@EverydayHomeRepairs

Жыл бұрын

Thanks for the support!

This guy is the real deal! Great explanation and instructions. I had a similar issue and this video helped me so much.

@EverydayHomeRepairs

Жыл бұрын

Happy to help 🙌

love shark bite used them to redo my entire cold water line, its been about 5 or 6 years now and not a single leak so far

Thanks. They want $500 plus to install a for one new sillcock installation. Mine is straight in. I have been watching videos to gain the confidence to DIY. I am getting more confident if I take my time and not rush.

Yes I need to see the other installed finish space spicket replacement

I clean carpets for a living since 1987 so I've literally hooked up to thousands of homes outside faucets for water. I've seen a whole lot of these freeze up during winter and cause a leak inside the home or under the house more times than I can even keep track of because it happens a LOT. I'm sure improper installation is the number one culprit. If they aren't sealed up against the wall properly or pitched properly it will only take one good freeze and you'll be needing either a repair or a replacement. When I clean I need to hook up to the outside faucet and believe me this has caused me trouble a lot of times over the years. I would almost bet money if I were a betting person that somewhere in the neighborhood of 1/4'th of all faucets in my area is bad as I type this. I'm in SE Missouri so our weather may get down to zero in the winter and rarely lower with wind chill. I very rarely see a faucet that is actually sealed up against the wall and often they're hanging very loose and not pitched properly so they can drain out when you take the hose off. Most people do remove their hoses in the winter, or at least they claim they do so improper installation is the number one cause IMHO of failure of these faucets.

Thank you for posting this detailed and helpful video:)

Wish I had seen this a week ago! I used the same fitting and had to install a flex line in between the spigot and supply line because of the offset.

Another winner here Scott. I was a little worried until you cleaned up the pipes. I’ve used SharkBite push to fit, and they have leaked, due to my error. All pipes must be burr free, inside as well as outside, so glad you covered that. I’m not a big fan of them, but feel they have their place, and make a good temporary fix. I’ve used the stops, on pipes I would have to come back to work on, and allow the water to be cut back on. I’ve got an outside spigot that needs to be replaced, but it should be relatively easy? It’s a frost free design, and it runs directly into the plumbing with a compression fitting. I just can’t tell what size I need, so I will buy a 10 and 12 inch spigot. There is a secondary cut off ( gate valve ) but it’s locked on tight. Sediment and some corrosion I’m sure, but PB blaster, WD 40, nothing will loosen it. I can just cut off the main ball valve at the utility area. I think your idea on other types of installs would be good. BTW, I just picked up the Klein NCVT you rec’d in a recent video, and it’s the best non contact tester I’ve used, so big Thanks for that! 👍👍👍😁✌🏻

@EverydayHomeRepairs

3 жыл бұрын

Hey George, sounds like you got a nice little project ahead of you. 😁

Great video thanks for all the great information. I would like to see the next video in doing it with having to cut through the dry wall . I have one that will need replaced but is in a finish part of my basement .

We had a record freeze in south Texas that burst some of my pipes. I had to cut into my inside wall to get to the faucet. Since I had paneling cutting into the sheetrock was no problem. I did have my plumber buddy do the soldering in the wall. It had to be done fast as not to burn the house down. I will try the SharkBite on other projects.

@EverydayHomeRepairs

3 жыл бұрын

Yeah, when you are starting off sweating pipes I think the open flame around wood does intimidate a good number of home owners. I wonder home many spigots burst during the freeze in Texas 🤯

@WaynJul

3 жыл бұрын

@@EverydayHomeRepairs Also a lot of vacuum breakers for sprinklers cracked. Most stores were sold out. I went to a industrial supply store and found one. He told me he had six left after ordering eighty.

Thank you for your time and effort!

The more challenging spigot behind the drywall is exactly what I'm dealing with, I would love to see a video on that

@EverydayHomeRepairs

Жыл бұрын

You might be in luck, I have 2 spigots which are covered by drywall and I am trying to work that project into the content calendar. Thanks for the feedback!

@RickWilliamscrm

Жыл бұрын

Yes Sir, I sure could use that video going into the wall, I have 2 I need to do and the plumber wants 350 each including the parts. 😩

Love the low voltage line wrapped around the copper pipe lol

Shark bite everything for 15 years and counting! Zero problems or replacements!

Thanks for making this video, great job.

thank you so very much- love to see the new drywall video!

Scott, This is great. I unfortunately have the issue where my spigot has been stripped (a Mr. Thread wouldn't even work) and it is frost-free and within the drywall, compliments of the former home owner who finished the basement. I am interested in learning about the drywall video - if you have one.

Love to see the other spigots.

@EverydayHomeRepairs

3 жыл бұрын

Thanks for feedback James 👍

Yes, I'm interested in the other spigot with the dry walll thanks.

For newbies, I would recommend purchasing the Sharkbite depth gauge. Using a Sharpie to mark the proper insertion depth on the pipe ensures a tight connection.

@EverydayHomeRepairs

2 жыл бұрын

Yep, not getting the proper depth I would guess is 99% of the reason behind people getting leaks with Sharkbie fittings.

@silekiernanphotography

Жыл бұрын

Yes, and use the debur tools. I've seen a debur tool that also measures depth. Very handy.

this was very helpful thanks.😃

Knowledge is Power. Go for it, I'm interested.

@EverydayHomeRepairs

3 жыл бұрын

Thanks for the feedback!

Great job and thanks!

Great video, especially for clueless DIYers like me.

@EverydayHomeRepairs

3 жыл бұрын

😂 thx!

I havent used sharkbite spigot before and that's what I'll use next time if the customer is ok spending the extra money for the part. Also want to comment on leak testing. You said you ran water out the spigot to look for leaks. The true test should have been conducted under pressure with the spigot turned off. That should have been mentioned in this video. Also you mentioned reusing the old part (90°) to avoid having having to purchase another sharkbite 90. I liked that you were able to reuse it. In my mind it's best to replace. Suggesting to reuse corroded copper piping is a shortcut and in most cases not recommended. Also it looks cleaner and reassuring to replace rather than reuse (best practice).

Yes you always have to measure and mark for depth so you know you have seated right and no leak. Also purge the water so you don’t make a mess

Well done mate👍🏽

Great video! Very cool! THANK YOU!

Great video!

I’m refinishing my basement currently and found my front yard water turn off valve buried behind 2 gas pipes that was all drywalled over. Definitely trying to make it leak proof now during the remodel compared to later on when it’s all buried again especially because I’m going to lose access to the shut off valve again

Very nice pertinent video. Would have been nice to show the removal of the end-cap sharkbite with the removal tool used to cap-off the supply copper pipe. Also, the supply copper pipe was not apparently sanded or cleaned before the 90-degree was attached, which could cause a terrible leak.

I would have just soldered it in that location as there is ease of access but nice to know that they have shark bite spigots.

I have a hard to reach spigot I need to replace, so a video on that would be great!

@EverydayHomeRepairs

3 жыл бұрын

Thanks for the feedback! 👍

Cool,that was great. Google must have seen my outdoor faucet? Thanks.

@EverydayHomeRepairs

3 жыл бұрын

Hahaha, be careful with those smart home devices 👀

Thanks for this video! I would like to see how to replace spigots behind drywall.

Thanks doing mine now..🎉

Excellent videos

Thanks for GOOD information !!

@EverydayHomeRepairs

3 жыл бұрын

You bet!

I didn't know sharkbite made those, thanks. My lines have shutoff valves inside house so when the spigot starts leaking I can just shut it off, until I can fix it.

@EverydayHomeRepairs

3 жыл бұрын

Nice! That is handy to have shutoff in place.

I knew it! Illinois too. Chicago here

@EverydayHomeRepairs

3 жыл бұрын

Yes sir, little south of you in Champaign area 👍

I would like to see how to replace the spigot in the finished area of the basement. Thanks for your great videos.

Nice job and video like always

@EverydayHomeRepairs

3 жыл бұрын

Thanks Donnie!

I live in New England, I didn't go through all of this. All I did was add a ball vavle inside so in the winter I shut it off and run the rest of the water out. You just really have to remember to shut the water off.

Outstanding

Yes, I need to replace in finished ceiling,in basement. Valve is in garage and it’s not obvious where it enters, I don’t want holes everywhere

I too, would like to see other valve projects

good video, nice to see the details ;)

@EverydayHomeRepairs

3 жыл бұрын

Happy to help!

Excellent

I would like to see the one that is in the dry wall as I live in CA and do not have those extended valves. Great content.

I'd be interested to see the other spigots start to finish, including dry wall. But this video is exactly the same scenario I'm in. I didn't even realize shark bite spigots were a thing. Thanks.

@EverydayHomeRepairs

3 жыл бұрын

They are handy 👍

@johnchonka2052

3 жыл бұрын

I wouldn't use them they leak get a real plumber to fix it right and will last

@scarce911

3 жыл бұрын

@@johnchonka2052 if you install them correctly, they are fine. Most leaks come from not deburring the inner and outer diameter..and making sure they are fully seated. Iirc got2learn goes over it a lot in pretty good detail .. when he put that cap on, he should have deburred the outside of the copper ..it tears up the rubber o ring (fyi: wrote before watching video)

@johnchonka2052

2 жыл бұрын

@@scarce911 where I live they fail alot due to extreme cold -20°f consistently and even colder. I've been plumbing 25+ years I'm old school I prefer soilder and expansion pex with male sweat brass adaptors. Sharkbite is for people that don't know how to Plumb. I will say I use sharkbit for temporary fixes example if I can't get the water totally off atm I'll use sharkbit until I can solider a permanent fix

@nc3826

2 жыл бұрын

at -20°Fa Sharkbite can prevent a burst cooper pipe, by acting as a relief valve... yes it will still leak but a Sharkbite can usually just be pushed back into place instead of having to find where the pipe burst and then having to repair it.... but I get it the trades hate to see anything.that will avoid a overprice service call.... FYI PEX A is better option than cooper to prevent freezing damage...

As a handyman/renovator in Canada, I am not a fan of the frost free wall hydrants, with or without the vacuum breaker. I've installed dozens and most never last more than 3 to 5 years. The majority are off-shore junk and parts, other than a replacement washer, are rarely available. I prefer the older KISS system (Keep It Simple Stupid). My 1928 home has three exterior spigots mounted through the poured concrete foundation wall. All are simple quality solid brass spigots. These valves now typically sell for about $8 compared to $55 for the newer 'frost free' type. I have repaired all three brass valves once during the last 46 years and one valve has just be repaired for it's second time. (Clean, replace washer and replace bonnet packing). I will recondition the other two spigots some time this summer, then they will all be good for the next 50 years. Canadian building codes require every external faucet to have a separate interior shut off valve with a bleeder valve. It takes about 2 minutes each fall to turn off the inside shut-off valve, bleed the excess water that remains between the inside and outside valves and leave the exterior valve open for the winter to prevent freezing when the temps sink to minus 30. I never plan to replace an outside spigot.

@AStanton1966

2 жыл бұрын

Along the lines of your reply, you don't have to drill a big hole for the conventional spigots. And I found one that is made with a ball valve. I installed that on the outside of my in-law's house. I think ball valves are easier to use for the elderly.

@chrisgraham2904

2 жыл бұрын

@@AStanton1966 I'm a big fan of 1/4 turn, full port ball valves for almost all valve requirements. Superior as an on/off shut-off valve, but not well suited for applications requiring throttling to control flow. Still works very well for outdoor faucets because throttling can be done at the hose nozzle.

@kooale

Жыл бұрын

Fabulous remarks. Big smile

@kooale

Жыл бұрын

@@AStanton1966 Aren't ball valves easier to turn for EVERYbody?

@AStanton1966

Жыл бұрын

@@kooale I suppose. Frost-free valves, having a longer valve stem, tend to drip a lot before shutting down. This makes people want to kill the valve and over-tighten them.

My parents had the same issue with one of their outdoor spigots. When I replaced it, I also added a cut-off switch just before the spigot in case I had to replace it again, just so I didn't have to turn off the entire house's water (like I had to do the first time :) In addition, I also added a small drop-down "box" over the entire area with a "door" that opened, giving access to the entire area (this too was in a finished ceiling). Painted, it more or less blended in (being in the corner helped too).

@Chris.Rhodes

3 жыл бұрын

Yeah, I added a dedicated shut off inside my house when I replaced my spigot. I have one main shut off, and that's it. I don't have dedicated shut offs. Whoever plumbed my house was an idiot.

@feelingtardy

3 жыл бұрын

i always add extra shut offs for water or gas whenever i have to take something apart. they always come in handy later on.

@wolfeadventures

2 жыл бұрын

@@feelingtardy but adds another failure point, no?

@kooale

Жыл бұрын

@@wolfeadventures I'm in a house that will be 100 years old next year. Things done right can last a very, very, long time without aver failing.

Would love to see the unit replaced through drywall! Thank you.

Well done.

@EverydayHomeRepairs

3 жыл бұрын

Thanks Hassan!

awesome thank you

In my situation there was no access from the inside. We had cut a big hole around the spigot and cut the pipe from the outside. Also it was too close to the tub to solder. So a Sharkbite had to be used. Because of that I was given the tail light guarantee.

Nice job for your situation. I need to replace my spicket but my cellar has 2x6 wall to a walk-in basement, therefore that spicket is way to long. I wanted to upgrade mine to a cold weather spicket but looks like I have replace mine with a regular short spicket.........

Can’t wait to replace these!! remove the hose bib and solder a new one on easy money! Cheap out now means you pay later!

Liked this and it was informative. But. I was really hoping to change my spigot from the round handle to the lever style for quicker on and off. I checked your site but didn't see that. Perhaps you could consider a video on that style or explain how I change from the existing round handle. If it matters, this is a Florida install. Enjoy your videos.

Good info. One note, you did not give the vinyl siding any opportunity to expand or contract with temperature changes.

I would like to see a video covering replacement of the shut-off valve. My house was built mid 70's and the valve doesn't work, as well as being in a horrible location. I know I could hire a plumber, but with my experience I would also love to do the job. But as I do with everything, pre task planning dictates I should probably make sure the steps I have in my head are accurate. Thanks for another great video!

@stich1960

2 жыл бұрын

Unless your good at soldering I don't recommend a large fitting like that, depending on age could be a screw on though. If the area is finished think of the damage that could be caused. I am fairly good at plumbing and do a small amount in a professional capacity, I would still hire it out for the peace of mind personally unless it was a trailer or screw on in an unfinished basement.

@Toyotajunkie

2 жыл бұрын

@@stich1960 It's currently soldered, but looks like it was probably "wet" while being done. More than likely replaced already. We have lived there for 21 years and it has been crap for at least a couple years. I have checked with a couple local places (small and large business) and they want $500 plus to do it. That just seems silly. I can call the utilities to shut off the water and that's only $35 (off and on). I'm more than able to solder, but I have never done a soldered valve before. I do agree though, when I have enough doubt or have failed at similar jobs I call someone. Ex: replacement of a fuse panel, not gonna do it. Lol. The knowledge is there but the risk is high enough that's it is worth hiring it out.

@stich1960

2 жыл бұрын

@@Toyotajunkie I mean you do you. It's fairly risky imo around here it's hourly and would probably be closer to 300+ parts. I would still do it if it's finished at 500 because it comes with insurance

@cpatton08051

2 жыл бұрын

You can do the exact same steps with a shark bite ball valve and use pex instead of copper eliminating the soldering aspect. Would cost you around $100 hose bib, ball valve, and pex. As long as the angle from ball valve to hose bib isn't crazy you won't need to crimp anything.

Yes; would like to see video how to replace spigot behind dry wall. That’s the kind I have to replce

great video thank you

@EverydayHomeRepairs

Жыл бұрын

You bet!