I've used your site over a decade ago and you still schooling me 😎

@MotorvateDIY

Жыл бұрын

Thanks... Your comment made my day!

Nice work thanks for your input into the Nissan/Infiniti world

@MotorvateDIY

5 жыл бұрын

Hey Christian Omenyi Jr, No problem.... the Nissan/Infiniti world is my second love :)

Dude you're the best! I needed this for so long!

@MotorvateDIY

5 жыл бұрын

Hey nemisans13, Great to hear!

@nemesis91101

5 жыл бұрын

@@MotorvateDIY do you know one for oil pressure? I think my temp got as high as 193-204f

@MotorvateDIY

5 жыл бұрын

Hey nemisans13, Most Nissan/Infiniti vehicles don't have an oil pressure sensor, so it doesn't exist. You oil temp is fine.... 212F is typical and helps to burn off any condensation in the oil from short drives. If your oil temp gets around 250F - 260F then it is getting a little too hot. You might want to edit the PID and change the maximum to 260F.

@nemesis91101

5 жыл бұрын

@@MotorvateDIY I did, except I only went to 220. My temp never gets above 206 or 208 :/ and that's at 90 mph on a 30min trip to work on the highway.

Heya! Got to say, your videos are very informative, thank you for your time and sharing the knowledge with us. Will try this on my 370Z 2020, cant imagine why it shouldn't work. Will send you a message, hopefully you will have spare few minutes. Cheers!

@MotorvateDIY

2 жыл бұрын

Thanks for your kind words! Please let me know if if does work on your 2020 370z.

@lexindigital

2 жыл бұрын

@@MotorvateDIY Will do Sir! Just sent you an email. Feel free to reply when you got a minute

@lexindigital

2 жыл бұрын

@@MotorvateDIY yep, it worked. Measurements match Advanced EX PID preset values. Cant compare their settings though as mentioned in my email :)

Works great with infiniti q50 3.0tt. Thank you kindly!

@MotorvateDIY

3 ай бұрын

Great to hear!

Any thoughts on where the reading is taken from? Is this the same as the VVEL oil temp available in the nissan advanced plugin?

@MotorvateDIY

5 жыл бұрын

Hey GeePeeZee, On the G37/370Z (or any VQ37VHR engine) the oil temperature sensor is located close to the oil filter and is brass coloured. Also, the Infiniti Advanced plugin uses the same sensor, but they call it the "VVEL Oil temp". I thought "Engine Oil Temperature" is easier to understand.

Hello, I have Infiniti g37s 2011 Europe version and still have (no response) in test and log. I tried three times delete and again create and still nothing. Do you have any idea? Thank you for your time

@MotorvateDIY

3 жыл бұрын

Hey Vojtech Tobola, The only thing I can think of is that the ECU programming for the European market is different than North America. Another option might be OBDFusion with the ~$14 enhanced OEM diagnostic add on.

Hi, Do you know the correct pid for VW DSG DQ250 gearbox (2016 year) ? To make a service, I need the gearbox oil temperature in realtime. I would be very thankful if you could help me. Thanks in advance!

@MotorvateDIY

Жыл бұрын

Sorry, but I don't know.

Hey man, awsome video, can i get the oil temperature from a citroen ds3 thp 1.6 turbo using the same equations or I need to use another equations?

@MotorvateDIY

5 жыл бұрын

Hey Gustavo Gomez Rodrigues, Generally the oil temperature PID is determined by the manufacturer, so my guess is that it is different. BUT you can try it and see if it works. The other option is to join a DS3 forum or facebook group and see if anyone has figured it out. Good luck!

Very helpful

@MotorvateDIY

5 жыл бұрын

Hey Ivan Alvarez, I'm glad you found it helpful. :)

Hello, I am trying to get some PIDs input for my nissan GTR and I cant seem to get them to work. I input this one exactly as you showed and i am getting failed response for formula. I've tried deleting and inputting over again and nothing. The OEM gauges on the screen are getting oil temp so i know the data is there just cant get the PID to work. Any advice? I'd love to get Transmission oil temp as well as engine oil pressure boost and what gear the transmission is in. Plus brake pedal %. I am trying to set all of these up to use with the Torque track record plugin to show telemetry while racing on the screen when recording.

@MotorvateDIY

4 жыл бұрын

Hey dzmedia, It looks like the GT-R is using a different PID for oil temperature. I have searched through my PID database and I don't have anything on the GT-R. I also did a quick online search and didn't see anything, either. I guess you will need to wait until someone figures this out. :(

@dzmedia

4 жыл бұрын

@@MotorvateDIY thank you for trying.

Will the value same for Bluedriver obd2 scanner to see engine oil temp? And any settings to see Transmission fluid temperature ?..

@MotorvateDIY

2 жыл бұрын

I don't think Bluedriver allows you to create a custom PID/gauge, so I think you are out of luck. :(

Do you have configuration (PID, etc..) for Automatic Transmission fluid level for g37s?

@MotorvateDIY

2 жыл бұрын

Unfortunately, I don't. There doesn't seem to be much data available on the Nissan transmission control modules (TCMs)... I will keep looking, and if I find something, it will be here!

Hi, I have a 09 370Z and Torque Pro, do you know how I can display the oil pressure with your method ?? Thanks !

@MotorvateDIY

5 жыл бұрын

Hey Damien, The 370z (and G37) doesn't have an oil pressure sensor, so an oil pressure PID does not exist. The only way to know the oil pressure, is to install a pressure sensor and gauge. :(

do u have PID numbers for 2017 Corvette. Looking for Oil Pressure, Oil temp, and TPMS numbers per tire

@MotorvateDIY

2 жыл бұрын

Hey Jerry, Sorry, but I don't... and I don't have access to one to figure it out. :(

Hello! Have You the PID (number of geabox velocities) to Mitsubishi L200 Triton 3.5 V6 Flex? Thanks from Brazil.

@MotorvateDIY

3 ай бұрын

Sorry, but I don't have anything on any Mitsubishi vehicles.

What about Honda accord 2017 i4 I can’t add a correct sensor numbers Looking for your help 🌹

@MotorvateDIY

Жыл бұрын

Sorry, I have no idea, as I don't know much about Honda vehicles. (and don't own one to figure it out)

how can i get this program ? for my vehicle would it be a app on my phone computer ?

@MotorvateDIY

4 жыл бұрын

Hey AnthonyTheKoon, That is an Android only app called Torque Pro and it runs on a phone or tablet. It is available at the google play store for about $5: play.google.com/store/apps/details?id=org.prowl.torque&hl=en_CA

Do you know the code for a 2008 Seat Altea XL with a VolksWagen 1.6 liter petrol engine with motorcode BSE

@MotorvateDIY

5 жыл бұрын

Hey Maurice NL, I have checked my database of OBD codes, and I don't have anything for Seat/VW. VW OBD codes seem to be very difficult to find out. :(

Great stuff. I have a 2016 Audi Q5. Looking for PID for oil temp and oil pressure. Ideas?

@MotorvateDIY

5 жыл бұрын

Hey Aj Weaver, No, I don't have any PID information for VW/Audi. It seems to be very hard to find.

Doesn't work for me on Car Scanner. 06 350z Rev Up Manual, I know I have an oil temp sensor. It either shows nothing or the app crashes. EDIT: saw a comment down below of a guy with an 06 G35 and you mentioned our ECU's use the ISO-9141 protocol. Would you happen to know the header for that? Edit 2: there's a wiki article that has standard PIDs under $01, one of which is oil temp (5C). Would I still use the same start and stop diagnostics commands that you have here if I can't use the CAN bus protocol you're using here.

@MotorvateDIY

5 ай бұрын

This is an excellent question that I don't know the answer to. :( What is shown in the video should work for any 2008 + Nissan/Infiniti engine that has an oil temp sensor, as CAN bus is used for diagnostics. However, for anything 2007 or older, it uses a different protocol (ISO-9141) and I don't have any way of researching or testing that. Before I found mode $22 oil temp, I made a "Y cable" and tapped into the factory oil temp sensor. Then I used an Arduino Uno/Nano to convert the voltage to engine oil temp. It worked well, but once I found engine oil temp on the CAN bus (car's network) I stopped using it. Unfortunately for you, Nissan didn't put engine oil temp on the CAN BUS until 2009/2010.

Hey could u give me the PID' for oil temperature for the new Honda civic type r fk8 model 2017.. Thanks. Can Find ECT and IAT with 0167 B-40 & 0168 C-40 but Cant find oil temperature.. I read All PID's with a snapon tester and i had found the oil temperature. Thanks.

@MotorvateDIY

5 жыл бұрын

Hy Melvin Melv, I thought this would be easy to find.... BUT after 1/2 hour searching I was not able to find any enhanced PIDs for Honda. If you want to know the PID, you could use a CAN bus sniffer while using the SNAP ON tool to read oil temp.

This is a great example of how Torque can be your best friend :) I have a Lancer 1.8 DiD 150 hp 2011and would love to see my particular filter differential pressure. It has a value in the system, which can be read on a OBD reader specific for the car - the value is in pascal. Searching high and low, I have not been able to find any method (that I understand...) on howto make a PID for this. From where have you found your values and how to set the PID up? Do you have a good link to learn how to understand the method...?

@MotorvateDIY

5 жыл бұрын

Hey Henning Sørensen, Items like particulate filter pressure are an "enhanced PID" and use a different method to see the value of the sensor. (OBD Service mode $22) Generally, finding the extended PID is difficult as they are not widely documented. Also, the extended PIDs are different for each manufacturer and sometimes different for different models from the same manufacturer. The only thing I can recommend is to keep searching the internet... maybe someone will figure it out.

Hello. By any chance you have PID custom for Mitsubishi Airtrek 2003-2005? Thank you sir.

@MotorvateDIY

4 жыл бұрын

Hey Shukry Ghany, Sorry, but I don't. All of the PIDs I have only work on CAN (2008+) networks.

Good explanation! Is there any code to check transmission oil temperature for an 2016 Audi A4 2.0TDI?

@MotorvateDIY

3 жыл бұрын

Sorry, but I don't have any information on Audi's (or BMW, or Mini, or MB) This type information seems to be hard to come by for German cars.

How do you get those PID and codes information ? I would like to try to get the same thing for Evo

@MotorvateDIY

Жыл бұрын

There are two ways... find it by searching, or reverse engineer a scan tool.

do you know how to do that with mercedes vito/viano w639 ? thank in advance

@MotorvateDIY

3 жыл бұрын

Nope. For some reason, it is difficult to find that information for German vehicles.

Hello, Do you know if for Mini this PID will work? If you have can you share the custom PIDs list for Mini Thank you

@MotorvateDIY

4 жыл бұрын

Hey André Pereira, Sorry, I have not come across any BMW or MINI PIDs. The PID in the video, only works for Nissan or Infiniti.

HI, thanks for the video, there's no way to do this with 350z of 2006?

@MotorvateDIY

3 жыл бұрын

I just checked the 06 350Z factory manual and it looks like there isn't an oil temperature sensor.... no sensor no data :(

Hi can you please tell me what values i can use for a 2004 mercedes cl55 amg thanks nice day.

@MotorvateDIY

5 жыл бұрын

Hey Rigardt strauss, Are you sure it has an oil temp sensor? Generally engines that don't have variable cam/valve timing don't have one, but since yours is supercharged it might. You need to find this out before going any further. The older German cars use a proprietary protocol and more than likely only the factory scan tool can show you oil temp. (as far as I know....) Maybe ask around in the AMG forums or Facebook groups - they may have the information you need. - Good luck!

can u help i cant read my oil tem in may Alfa Romeo 156 v6 busso engine ??

@MotorvateDIY

5 жыл бұрын

Hey André Da Cunha, All my documentation is for cars sold for the North American market. I have very little information on cars sold in Europe. I tried searching for "Alpha Romeo oil temp pid" and didn't find anything. I might want to try an Alpha 156 forum or Facebook group... Maybe someone there can help. Good luck!

How do I find the PID sensor code to get engine oil temperature for a 2005 Scion xB? How do I get a list of PID for the available sensors for the xB?

@MotorvateDIY

7 ай бұрын

For engine oil temp, you first need to make sure your engine has an engine oil temp sensor. I don't think the xB does have one, as Rockauto doesn't show a oil temp sensor for a 05 xB, so that info is not available (However, sometimes the oil temp is calculated) For the list of all extended PIDs, search for them online, or reverse engineer them yourself, which is not quick or easy. It took me about 60 hours of research and testing to get engine oil temp from my G37. For an easy option, look into OBD Fusion $20 Enhanced Diagnostics for 96 - 2021 Toyota vehicles: www.obdsoftware.net/software/obdfusion

Whats the exact code for farenheit, i put the code on the video but kept getting errors. Also Im havin an issue where ill get the reading and I hit ok but when I exit to add the display on realtime it doesnt work anymore, the engine oil temp display stays black and when I go back into the PID menu to test it again it wont work. 2010 G37 sedan

@MotorvateDIY

3 жыл бұрын

For engine oil temp in °F use this formula: (A - 50)*9/5 + 32 As for your Torque Pro issues, you might want to ask the Torque Pro forums: torque-bhp.com/forums/?wpforumaction=viewforum&f=1.0 Good Luck!

Hi do you know the pid for cvt temp for nissan rogue 2014? Thanks

@MotorvateDIY

3 жыл бұрын

I am doing some reverse engineering right now to find out... When I know, I will pass it along :)

Thanks, what about OBD Fusion if I want the same custom PID?

@MotorvateDIY

5 жыл бұрын

Hey Adnan Hnoosh, Hmmm... I am not sure. In the past it didn't work with OBD Fusion as they didn't support the elevated diagnostic mode 10C0. However, with their enhanced diagnostic add-on, it has oil temp plus a LOT more.

any way to monitor the trans temp through torque pro app on q50?

@MotorvateDIY

3 жыл бұрын

Hey Tianhao Wu, Not that I know of... :(

Do you know of any specific source for other audi specific PIDs?

@MotorvateDIY

5 жыл бұрын

Hey Aj Weaver, Nope, as mentioned below, it seems to be very hard to find. I guess no one has reverse engineered them :(

Will you have oil pressure pid for a 2009 Audi A3 in Torque pro ?

@MotorvateDIY

3 ай бұрын

Sorry, but I don't have anything on any Audi vehicles.

Do you know the code for a 2016 VF ss series 2 with the ls3?

@MotorvateDIY

Жыл бұрын

Sorry, I don't know anything about the Holden Commodore :(

Just wondering if you had a chance to make any progress on the Transmission Oil temperature PID for G37 AT? By the look of the google search and comments here its a really wanted subject as a lot of people looking for it but no one can figure it out. Your oil temp video is really helpfull. Thank you

@MotorvateDIY

4 жыл бұрын

Hey GuD2BeEvL, Not really. I was able to get the auto trans oil temp on a 2018 Maxima, but it uses a different type of transmission. (CVT) On my other channel (obd4everyone), I tried to help a G37 owner get the trans oil temp using OBD Fusion with their enhanced diagnostic add-on. For some reason on their car, the TCM (transmission control module) was greyed out. The next time I am at the scrap yard, I'm going to grab a TCM so I can test it on the bench and get to the bottom of this :)

@nicolapalumbo3071

4 ай бұрын

​@@MotorvateDIYHi please can you help me for FORD FIESTA MK8 2019 DIESEL for PID engine Oil Temperature? Thx....

Very nice tip! Will this work on a 2018 Subaru WRX STI ? Thanks

@MotorvateDIY

5 жыл бұрын

Hey Fernando Roman, Nope... that PID only works for Nissan and Infiniti vehicles. but 2210AF with the formula of A*9/5-40might work...

@fernandoroman4779

5 жыл бұрын

Motorvate DIY Thankyou! I will give it a try

Hello, i just purchased a 2014 Mini Cooper S Countryman that i would like to purchase a bluetooth scanner so that i can see engine oil temp, transmission oil temp, turbo boost, engine coolant temp, etc. I do not want to have to wait for an idiot warning light to come on before i know i have a problem. Can you recommend an android app that will show me all these and more? Thank you in advance.

@MotorvateDIY

2 жыл бұрын

Sorry, but I don't know anything about the R60 Mini or how to get those data items/gauges via OBD. Engine coolant temp and boost should be available on the standard/mandatory PIDs. (OBD "live data") The others may require using an "extended or enhanced PID", if they are available. The BMW enthusiasts seem to like Carly, so you might want to have a look at that. www.mycarly.com

Hello. Congratulations for what you do. could you help me to display the engine oil temperature on an Audi A4 B8 2.0 TDI. Thank you

@MotorvateDIY

4 жыл бұрын

Hey Ameziane HAMDANI, Sorry, but I don't have that information and it seems to be hard to find. (I have tried)

Great work! Unfortunately it doesn't work for seat ibiza 1.2 tsi cbzb ea111 engine :(

@MotorvateDIY

5 жыл бұрын

Hey Ecarnomics official, The "enhanced PIDs" are manufacturer specific, so a Nissan/Infinit one won't work on anything else. However, this should help you get your oil temp, if your engine has an oil temp sensor: forums.tdiclub.com/showpost.php?p=3546167&postcount=12

I need your help i have an audi tt mk1 and it doesn't work for me

@MotorvateDIY

4 жыл бұрын

Hey Panos Jok, The steps in the video only work for Nissan engines. In the past, I have search for the oil temp pid for vw/audi, but I didn't find anything. Since I don't have access to a VW/Audi, I didn't speed too much time searching... Good luck on your hunt for oil temps!

Hey buddy, gret video i have a g37 2012, this method would 100% work?

@MotorvateDIY

3 жыл бұрын

It should :)

Great video, thanks! I have a 2019 Nissan Armada and am using Torque Pro through a USB adapter. I have a gauge for the Transmission Temp (method 1), and another gauge for Engine Coolant Temp. But the two always read the same, identical. That can't be possible. Would you know how to add PID's for those two sensors manually?

@MotorvateDIY

3 жыл бұрын

The engine coolant temp should increase at a much faster rate, until the thermostat opens up, then it should be about the same temp around 85C 185F. If they are always the same, then the PID is probably incorrect. The engine coolant temp PID is a standard one, and should be available in Torque Pro. If you want to manually it look here: en.wikipedia.org/wiki/OBD-II_PIDs#Service_01_PID_00 PID 05 is the engine coolant temp. to use it, just send 01 05 (request mode 01, PID 5) and the number that is returned is the engine temp BUT you need to subtract 40 to get temp in degrees C. I don't have anything for the automatic trans temp :(

@michaelbargiel760

3 жыл бұрын

@@MotorvateDIY Thank you!

@michaelbargiel760

3 жыл бұрын

@@MotorvateDIY Another question: Looking at the Wikipedia page you linked to, I would think code 01 A4 should return Transmission Actual Gear. However, it returns No Data. Is there a special code for Nissan (Armada)? Thanks

@MotorvateDIY

3 жыл бұрын

Just because the SAE defines a PID, doesn't mean the manufacture needs to implement it... and as you have seen, Nissan didn't implement 01 A4. Using enhanced diagnostics, I think you should be able to get the current gear ratio, but since I don't have a Armada, I can't test that :(

Hi, is this going to work on E46 as well with that app? I am looking desperate for Oil temp/pressure for E46

@MotorvateDIY

4 жыл бұрын

Hey Marcin Adamczyk, Nope :( Each manufacturer defines the codes and sensors (PIDs) that can be viewed through the OBD port. The engine in your car (M54, I think) doesn't have an oil pressure sensor, so it is not possible to view the oil pressure through the OBD port. If you want oil pressure, you will need an aftermarket oil pressure gauge. Through DIS, INPA, BMW Scanner, etc you can view the oil temperature, through the OBD port. MAybe check and see if the Carly app (www.mycarly.com/en/app/bmw/) can show oil temp???

@marcinadamczyk7142

4 жыл бұрын

@@MotorvateDIY thx a lot for a prompt and comprehensive answer.

@MotorvateDIY

4 жыл бұрын

Anytime :)

How about PID for engine oil pressure for chevy optra 2009?

@MotorvateDIY

2 жыл бұрын

It doesn't exist... That car doesn't have an oil pressure sensor, just an oil pressure switch.

Hello, what about Seat Leon CUPRA 1p 2.0tfsi, engine bwj. Thanks

@MotorvateDIY

5 жыл бұрын

Hey ISoOYI, Sorry but I don't have any documentation on cars outside of North America. BUT, your car is on VW's MQB platform, so search for "vw oil temp pid" and you might find your answer.

Hey man i have a question. This custom pid never worked for me but i just used the vvt oil temp and worked fine for months BUT tonight it just says ExtPid Not found. (Same for brake switch and maf sensor). Coolant temp works for some reason. Tried uninstalling torque pro and nissanEx,InfinitiEx No dice. I need to read my oil temp ._. Any ideas?

@MotorvateDIY

4 жыл бұрын

Hey DevilG, Well this is interesting.... I just saw your post on myg37.com! (small world!) SonicVQ's reply should work as I have had to do the same thing and that worked. For everyone else, here is something to try to get Torque to work again. • uninstall the plugins • uninstall the app • deleted the Torque Pro app directory and log directory • restart the Android device • reinstall torque, and the plug ins Don't forget to configure the Infiniti EX pluging to select the proper engine/vehicle.

@devilg37

4 жыл бұрын

@@MotorvateDIY thanks man,ill try this. Yup i just saw Sonics reply. Thank you both for the tips! Definitely small world, im a toronto local as well lol Btw your vids are awesome, ive used them many times to work on my G. Keep this channel going, its awesome! Cheers and many thanks 🍺 (edit: it works again following after following those steps)

@MotorvateDIY

4 жыл бұрын

Hey DevilG, Thanks for your kind words and I am glad you got it running again :)

Great video. I have a question. So why is this important? Is this for people who have a heavy foot? Is this for people who are tuning?

@MotorvateDIY

5 жыл бұрын

Hey DeathDealerHype, Excellent question! Knowing the oil temperature tells you: (1) When the engine is fully warmed up. It can take 10-15 minutes longer for the oil temperature to equal the engine coolant temp when fully warmed up (around 85C, 185F) (2) How hard your engine is working. Nissan/Infiniti's 3.7 litre V6 has VVEL, which partly controls the throttle by changing how much the vales lift/open. Under full throttle, the oil heats up VERY quickly and if it exceeds 126C / 260F the ECU reduces engine power to prevent increased engine wear. So yes, this is useful to people with a heavy foot or for anyone who races. Also it is fun for "information junkies" like me. :)

Does it work on rotarys? Mazda rx8 thanks

@MotorvateDIY

5 жыл бұрын

Hey charles corbin, No it won't. The code for oil temp is specific to Nissan/Infiniti engines. Each manufacture uses their own code for different sensors. To figure out IF you can get to work on a RX-8 you need to find out if the engine has an oil temperature sensor from the factory. No oil temp sensor means it can't be done using an app. If it does have n oil temp sensor, then you need to figure out what PID to use which can be VERY difficult to find. I don't have a listing in my database of Mazda codes. I think your best option is aftermarket gauges.

Would this work on my 06 sentra 1.8?

@MotorvateDIY

4 жыл бұрын

Hey mike flores, I don't think so. As far as I can tell, your engine (QG18DE) doesn't have an oil temperature sensor.

Hi thx info. Could works Mitsubishi Lancer Evolution X 2012???🤔

@MotorvateDIY

Жыл бұрын

Nope... This is only for Nissan/Infiniti vehicles that have an oil temperature sensor. I don't know anything about Mitsubishi vehicles, so I can't offer any suggestions. :(

Hello bro thanks for the awesome DIY vids I have been searching all day for PIDs!! the car is a 2002 Lexus IS300 stock 2JZ-GE Is there anyway you can hook me with the PIDs? i'm looking for Engine Oil Pressure & Engine Oil Temp

@MotorvateDIY

5 жыл бұрын

Hey Moe Nas, I don't think that engine has an oil temperature sensor from the factory... and if that is correct, there isn't a PID for it. I know that it doesn't have a factory oil pressure sensor (very, very few do), so no luck there as well.

Hi! How can i get the oil temperature for the Volkswagen 1.2 TDI engine? It's a SEAT Ibiza (POLO)

@MotorvateDIY

3 жыл бұрын

Sorry, but I have no idea... My area of expertise is on Nissan & Infiniti VQ engines. The last VW engine I worked on was in my 83 GTi and that way way before OBD. BUT it did have an oil temp gauge!

@dsj9898

3 жыл бұрын

@@MotorvateDIY No problem sir! Thanks alot for responding to my question. Mine only has a coolant temp. gauge.. I'll search for another solution ;)

Hello. Nice video. But do you have som PID custom for Subaru Impreza 2008? Thanks for answer.

@MotorvateDIY

4 жыл бұрын

Hey tomino1308, I think I do... can you let me know if this works? • Name: Engine Oil Temperature • Short name: EOT • Mode & PID: 2210AF • Equation: A*9/5-40 • Min: -30 • Max: 300 • Unit: F 7 • Header: 7E0

@asensniper

4 жыл бұрын

@@MotorvateDIY Tried this on my '12 impreza STi, doesnt work, perhaps you have another idea?

@MotorvateDIY

4 жыл бұрын

Hey Chad N, On my 2015 Forester, the standard OBD PID 0x5C shows the oil temperature... Well at least in OBD Fusion ... I will check later tonight if Torque shows it as well. Sometimes Torque doesn't decode the datastream accurately.

I am assuming this is for specific Ecu / car. Thanks

@MotorvateDIY

2 жыл бұрын

Correct! It would be nice if the car manufactures worked together to standardize these things... but they don't. However some manufactures do have engine oil temp as part of the standard OBD offering like on the 2015 Forester.

Hi, thanks for the info. Could work in a Megane RS 250?

@MotorvateDIY

2 жыл бұрын

It just might... This does work for Nissan/Infiniti vehicles, but since Renault partnership, it may work. Give it a try and see. Good luck!

@rs250

2 жыл бұрын

@@MotorvateDIY ok, It doesn't!! =( My RS 250 don't have the sensor. The Megane RS265 have it with the extra RS monitor. I will add and external sensor. Thanks!

Hmmm, I'd love to find a way to check Engine oil pressure for my 2009 G37 on Torque. Perhaps there's a way to install an actual sensor where the Oil pressure switch is and link that sensor up to Torque?

@MotorvateDIY

4 жыл бұрын

Hey ssj4david, That would be nice... however that would be VERY difficult. You would need to find a unused analog input in the ECU, then update the code to use that input and calculate oil pressure.

@ssj4david

4 жыл бұрын

@@MotorvateDIY I'm just curious. Aside from doing regular synthetic oil changes every 6000-8000km, and not thrashing the engine until it gets to temperature; what are some "best practices" to ensure the Oil Gallery gaskets can last as long as possible? Car has about 203,500km; but everything seems to be holding up strong. Thx in advance

@MotorvateDIY

4 жыл бұрын

Hey ssj4david, That's a good question. However, I don't think there is anything that can be done to prevent or delay the oil gallery gaskets from blowing out. I don't have any hard data, but I do believe that this only happens to a small percent of engines. I would recommend getting an oil pressure gauge (150 psi) so you can keep an eye on it and if they do start to go, you won't damage the engine.

Hi thanks for your vids thety are awesome! I have a '08 370gt, it can't communicate with my OBD2 scanner. Any tips mate?

@MotorvateDIY

5 жыл бұрын

Hey Steve S, Thanks for your kind words! Just to clarify, the Torque app can't communicate with your OBD2 scanner, or your car can't communicate with your OBD scanner? What scanner do you have? Has the scanner worked on other cars?

@chiangth23

5 жыл бұрын

Hi. Mine works well on other gauges just not EOT. I followed the steps but it still shows no data. I’m using OBDLink MX

@MotorvateDIY

5 жыл бұрын

Hey chiangth23, What car are you trying to get the EOT to work? The PID shown in the video works on Nissan/Infiniti vehicles sold in North America. If you car is sold in a different region, it is possible for the code to be different, or even for the OBD system to be locked, and require a special code. Was you car made for the North American market? If not, which one?

Do you know if this works on 2007 G35X sedan? Seem not :( I am trying to get any of the extended PIDs to work with my car, 111F, 1115, 1103, 1102 (found these on a 370z forum). None of them work but if i manually enter a standard one like 0105 it works fine

@MotorvateDIY

4 жыл бұрын

Hey vgg1, Just for you, I set up a 2007 G35x ECU on my test bench to test. It looks like the 2007 ECU does not support the CAN bus protocol and use the older ISO 9141-2 protocol. All 2008 model are required to support the CAN bus protocol. This means your ECU only supports the OBD services from $01 to $09. Your entry of 01 05 (engine coolant temp) uses mode $01. The oil temp PID in the video uses mode $22, which your ECU doesn't support as requires the CAN bus protocol.

@vggupta95

4 жыл бұрын

@@MotorvateDIY Wow, thank you for checking for me! Do you know how I can pull extended data from the ECM/BCM/ETC via OBD? OBD Fusion does work on my car and i can see stats such as tire pressures, intelligent cruise control stats, 4WD stats, etc. But what I am trying to do is pull this info in through my Raspberry Pi and display it on the dash. So I know it is possible (through fusion) but I am not sure how they are doing it.

@MotorvateDIY

4 жыл бұрын

Hey vgg1, Well.... I did some more digging for you. As it turns out, the standard OBD communications are done using the ISO 9141-2 protocols. BUT the OBD Fusion enhanced communications looks like it switches over to the CAN bus. I don't know how they do it, but if you sniff around, I'm sure you can figure it out.

@vggupta95

4 жыл бұрын

@@MotorvateDIY Ok thanks, hopefully I can find some info about it somewhere. Thank you for checking for me!!

Hi! Any chance you know how to get the oil temperature on a Volvo V90?

@MotorvateDIY

4 жыл бұрын

Hey interceptor213, Nope... I don't have any Volvo extended PIDs. Some makes are very easy to find the extended PIDs (like Nissan) and others are VERY hard to find. (VW, Volvo, Honda)

@interceptor213

4 жыл бұрын

@@MotorvateDIY thanks for your quick response! I'll keep looking...

Do you have anymore pids for infiniti/nissan like transmission/ac ect??? I have a VR30DDTT

@MotorvateDIY

2 жыл бұрын

Nope I don't... Once I purchased the OBDLink MX+ I stopped looking, as it can read all the sensors on all the modules on my G37.

@kandidady3271

2 жыл бұрын

@@MotorvateDIY thank you.. now I use odb fusion and it has everything I was looking for

@Qkfltpdls777

Жыл бұрын

@@kandidady3271 what is obd fusion?

Will this work with OBD fusion?

@MotorvateDIY

5 жыл бұрын

Hey bommerang, I don't think so... OBD Fusion does not allow you to enter/exit the required diagnostic mode. HOWEVER... Their $15 enhanced diagnostic add-on gives you access to that and many (like 200+ more) PIDs. Here is a video from my other channel OBD 4 Everyone that shows it and how to set it up kzread.info/dash/bejne/i4iiutdyetfTmLw.html

this Works on mini r56? Thank you!

@MotorvateDIY

3 жыл бұрын

Sorry, but I don't have information on BMW/Mini vehicles.

Do you have one for a Jeep JK Transmission Temp??

@MotorvateDIY

Жыл бұрын

Sorry, but I don't.

Can you provide a pid for oil temp for bmw e46?

@MotorvateDIY

5 жыл бұрын

Hey Clarence Trinidad, I spent about 30 minutes trying to find the oil temp PID for the E46..... but nothing was found. On my E39, the only way I can get the oil temp is by using INPA or BMW Scanner. I suspect the platform is tool old to support OBD extended diagnostic PIDs.

Hi, GREAT DIY! I am trying to read EOT from my 2013 Toyota Camry SE 2.5L 4-Cyl DOHC 16V w/Dual VVT-i , but no success so far. I use ELM327 Super Mini BT x Torque Pro. Please could you help? Thank you. Marek

@MotorvateDIY

4 жыл бұрын

Hey Marek Plevak, I have search my files and I don't have any engine oil temp enhanced OBD codes for your 2.5 litre engine Camry. As you know, these enhanced OBD codes difficult to find. To find them out, you pay thousands to Toyota or reverse engineer them.

@yoshimara007

4 жыл бұрын

​@@MotorvateDIY Thank you for your answer anyway! I will try to continue with investigation. Take care!

Do you have the pid for the IAT?

@MotorvateDIY

Жыл бұрын

Intake air temperature is a generic PID (0x0F) and will be shown with the other OBD items. (like engine RPM, coolant temp, etc)

thanks for your videos, very clear and very helpful. I am about to buy my first OBD2 scanner, but I need help in choosing which one, specifically for my car, I need to know the transmission oil temperature in real time, this is necessary to do the gearbox service and determine the exact oil level at a specific oil temperature. I am writing to you from Europe, do you think it is possible to obtain this value with your own OBD2 scanne, or if you can recommend me one to buy, thank you. My vehicle is a model: Infiniti Q30 2.2d. AWD 170 Hp 7gDCT, Diesel, and mounts Mercedes OM651 engine and Mercedes 724 automatic transmission. I am especially interested in having the temperature of the automatic transmission oil in real time, in Infiniti they use the official one Xentry (Mercedes) I don't know if you can help me, but thank you anyway for your very useful videos.

@MotorvateDIY

4 жыл бұрын

Hey Louis Gerard, To be honest, I really don't know. On newer Infiniti vehicles you can read the transmission oil temp through the OBD port, but your engine & transmission (and other modules) are made by Mercedes. After I quick search I did find this: mbworld.org/forums/c-class-w204/757159-obd2-scanner-measure-transmission-fluid-temp.html That might be just the tool you need, but I don't for certain as I don't know which components are made by Infiniti or Mercedes. Good luck!

@louisgerard2148

4 жыл бұрын

@@MotorvateDIY thanks for the advice, I will continue to look for what I can find that is right for me. For example, I sent emails to both Autel and Launch, asking for information, they still have to answer me. I found this model: kzread.info/dash/bejne/qXWtpqqbkqyWpJM.html but I still have to know if it's okay for me, i need to bleed ABS system brake too Thanks again and continue with your very useful videos

Could you please share the csv or the file where has all V36 g sedan’s PID list?

@MotorvateDIY

Жыл бұрын

I don't have a "ready to go" CSV file, but I'll search through my files and see what I have over the next few weeks.

@Qkfltpdls777

Жыл бұрын

​@@MotorvateDIY Could you please share the "ready to go" CSV file if you could sir? Please

Hi. It works on my Nissan Juke but it only shows the oil temp of the specific time I open the torque pro. Then it doesn't change and I have to restart the app to show me the correct oil temp again. It says "waiting for data"

@MotorvateDIY

2 жыл бұрын

That's too bad. Unfortunately I have no idea why. Maybe the Torque Pro forum can help: torque-bhp.com/forums/?wpforumaction=viewforum&f=1.0

@MotorvateDIY

2 жыл бұрын

Looks like the problem is on the Torque Pro app side: torque-bhp.com/forums/?wpforumaction=viewtopic&t=16524.0

@srtfitness1494

2 жыл бұрын

@@MotorvateDIY It worked. Torque just needs an update from Google Play to the latest version. Thanks a lot.

@MotorvateDIY

2 жыл бұрын

Thanks for letting me know :)

Do you have a video for transmission fluid temperature? I have a 07 G35 sedan with the 35hr so I imagine it would be the same.

@MotorvateDIY

5 жыл бұрын

Hey bpattillo, Not yet... however I'm working on it. Part of the problem is that I don't have easy access to an automatic G35/G37.

@MotorvateDIY

5 жыл бұрын

Hey bpattillo707, Not yet, but I am working on it. Part of the challenge is finding an automatic G35/G37 that I can scan.

@BPattB

5 жыл бұрын

@@MotorvateDIY I know they have 2 different transmissions the 35's have the 5at the 37' are 7at's. If I was up in Canada I'd come see you lol. I googled around a lot and couldn't find anything about Nissan automatic transmission fluid pid's. I did see on some forums about how closely a guarded secret some of the information is, something to do with the consultant 3 licensing. Sucks I have to have a accurate reading of 149 degrees to check the dipstick. I don't even have my ob2 scanner yet I order it the same day I watched your video. Your G videos are great by the way.

@MotorvateDIY

5 жыл бұрын

Hey bpattillo707, Thanks for your kind words! At the next local G37 meet, I should be able to scan an auto G37 and hope to make progress. The auto trans temp is high on my list of items to figure out :)

@BPattB

5 жыл бұрын

@@MotorvateDIY I emailed a few of the apps asking if using their apps I could access transmission temperature in my 07G and fusion responded. Hello, Transmission temp isn't available over generic OBD2, but we have enhanced diagnostics for Nissan/Infiniti vehicles that can access transmission temp. When you connect with enhanced diagnostics, the add-on will scan your vehicle for supported enhanced PIDs. Regards, Matt I wonder if "enhanced diagnostics" is there own upgrade? I'll let you know. Im working 12 hour shifts for the next 4 days so it will be a little while.

Sorry but I’m a little confused when you say that most Nissan’s don’t have an engine oil temp gauge , Doesn’t the 370z have one in the middle of the dash above the radio?

@MotorvateDIY

3 жыл бұрын

As far as I know, the 370z is the only Nissan that does have an oil temp gauge. Every other Nissan and Infiniti does not... so most don't :)

Post a video on the the jacking up the G and jack stand points

@MotorvateDIY

5 жыл бұрын

Hey nawmean, I just may have that raw video from a few years ago. I didn't make it an episode as I wasn't sure of how useful it would be. I will have a look and see if the raw video is decent. Until then, this may help: kzread.info/dash/bejne/fISOlsWcdruzgco.html

I have a 2009 350Z HR model. So basicly a 370Z. The 350Z HR did have a Oil temp sensor, not like the DE models, but your method dosent work for me. How can i get the result that you have? Can you please help me?

@MotorvateDIY

4 жыл бұрын

Hey Fightbird2013, Well.... that is interesting. The only extended PID code I have for Nissan/Infiniti engine oil temp is the one shown in the video. As you know, these codes are difficult to find and sometimes the manufacturer changes them :( One option is the "Advanced EX for NISSAN" plug in for Torque. For about $7 is should give you oil temp and a few other items.

@Fretke3514

4 жыл бұрын

Same here no respone

@MotorvateDIY

4 жыл бұрын

Hey Dominique Mostert, Crap! Sorry to hear that. What year and model do you have?

@MotorvateDIY

4 жыл бұрын

I spent a few hours researching why it isn't working for some. It looks like this should work with any 2008 and up engine that has an oil temperature sensor. I could not get it to work on a 2007 G35 (with VQ35HR). This is because the 2007 ECU ignores the oil temp request. I would expect the same result for a 2007 350Z. I don't have access to test it on a 2008 350Z or G35, but it should work. Technical Details why 2007 HRs don't connect. When Torque connects to the 07 HR ECU, it uses the ISO 9141-2 (K-line) protocol. The 22 111F command needs to be sent to the CAN bus using the ISO 15765-4 CAN protocol. Torque Pro can't switch to the CAN network and sends the CAN 22 111F command to the K-line / ISO 9141-2 protocol, where it is ignored. Starting in 2008, all cars sold in North America must use the ISO 15765-4 CAN protocol for OBD. Since Torque Pro doesn't need to switch protocols, it should work. Anyways, that's my theory.

@MotorvateDIY

4 жыл бұрын

I didn't think the 350z was sold in 2009... Is that a typo and meant 2008? I spent a few hours researching why it isn't working for some. It looks like this should work with any 2008 and up engine that has an oil temperature sensor. I could not get it to work on a 2007 G35 (with VQ35HR). This is because the 2007 ECU ignores the oil temp request. I would expect the same result for a 2007 350Z. I don't have access to test it on a 2008 350Z or G35, but it should work. Technical Details why 2007 HRs don't connect. When Torque connects to the 07 HR ECU, it uses the ISO 9141-2 (K-line) protocol. The 22 111F command needs to be sent to the CAN bus using the ISO 15765-4 CAN protocol. Torque Pro can't switch to the CAN network and sends the CAN 22 111F command to the K-line / ISO 9141-2 protocol, where it is ignored. Starting in 2008, all cars sold in North America must use the ISO 15765-4 CAN protocol for OBD. Since Torque Pro doesn't need to switch protocols, it should work. Anyways, that's my theory.

Can you please provide PID configuration for ATF temp for V36 G35/G37 sedan as well?

@MotorvateDIY

Жыл бұрын

I'll go through my files and see what I have.

@Qkfltpdls777

Жыл бұрын

@@MotorvateDIY thank you sir

@Qkfltpdls777

Жыл бұрын

It would be great if you can create a short clip how to add ATF temp as this video. I could see ATF temp by my friend’s Autel Maxis DS808 though.. can I extract some information from that scanner?

I tried at Honda but cannot work. This pids same like for Honda?

@MotorvateDIY

4 жыл бұрын

Hey Evo 2, Every manufacturer defines what the different codes (or PIDs) are. These ones will only work on a Nissan or Infiniti. Try an online search for "honda obd oil temp pid"

@evo2252

4 жыл бұрын

Can u try for Honda? I tried with many pids but cannot work. So, please help to me Honda Engine Oil Temp and Pressure.

@MotorvateDIY

4 жыл бұрын

Hey Evo 2, You might want to do some research to see if you engine has an oil temperature sensor. Not every engine does. If it doesn't have one, there won't be a PID for it. This may explain why I couldn't find anything searching online. In my PID databse, I don't have anything for Honda. Most of that has to do with that I don't own a Honda, so I don't spend a lot of time searching. Good luck!

hey, do you know how to get addresses for audi a4 b9? ty

@MotorvateDIY

3 ай бұрын

Sorry, but I don't have anything on any Audi vehicles.

In behalf of those that have done this, THANK YOU! My average temps go from 80-94 which is the highest i have seen them. I'm monitoring as I see see very minimal metal in my oil so I'm using cheap oil to flush and monitor. Is there a way to change the calculations so it can measure in Fahrenheit instead of Celsius? How are things going with the crank case pressures? Myg37 user.

@MotorvateDIY

4 жыл бұрын

Hey Oscar Del Toro, You oil temps look good, but don't worry if they go higher in the summer. Yesterday I went for a 1 hour drive on the highway and the G37 oil temp was just over 90C. Oil temps in the 90-100C range are good, as this ensures any water vapour in the crankcase or oil will be removed. Did you know....For every gallon of gas burned, almost a gallon of water is created by the chemical reaction? I didn't until recently and that is why the 90-100C oil temps are important! To have the oil temp in Fahrenheit, just change it to "(A-50) x 1.8 + 32" The " x 1.8 + 32" is the typical conversion factor to convert C to F. As for the crankcase pressure research, there has been a lot of progress! I built a new data logger that samples the crankcase pressure 2,000 times per second, from 5 different sensors (to make sure the recorded pressures are accurate) which are located in two different locations. The new data logger is working well and capturing consistent data. I have converted my PCV system to an "open" system and did one short test at idle to collect the first point of data. On the next weekend with outside temperatures above freezing, I will capture a few wide open throttle runs with and with out the PCV system, and then start the analysis. The final results will take some time as it is important to me to make sure the sensors, data logger and analysis are as accurate as possible.

@oscardeltoro898

4 жыл бұрын

@@MotorvateDIY that's a very interesting perspective as I did not factor that. I want to start experimenting with different weights and synthetics and explore Torque as I'm in love with the app. (A-50) x 1.8 +32 typed just like that is giving me a syntax error, it's possible the spaces between symbols could be causing this etc. I realized crankcase video will be extremely insightful and needs to be thorough as it will be a hit but for it you need to have the right data which takes time. Thanks again.

@MotorvateDIY

4 жыл бұрын

Hey Oscar Del Toro, My fault... I typed "x" for multiply and not "*" Try this: (A-50) * 1.8 +32 I like what you are going to be testing, but keep in mind the engine oil temperature is GREATLY impacted by engine RPM. (not load just RPM) The oil pump in the VQ37VHR is quite large and it pumps a lot of oil. BUT when you pump a lot of oil, it increases the temperature. Ever feel the heat from an air compressor tube that runs into the tank? They get very hot when the air is compressed, the sames goes for the oil temp. Good luck with the testing and please let me know where I can find your results.

@oscardeltoro898

4 жыл бұрын

@@MotorvateDIY I'm BULL in myg37.com I'll probable reply to one of your threads or even here.

@MotorvateDIY

4 жыл бұрын

Hey Oscar Del Toro, (aka BULL) I spend a little bit of time on myg37 and have seen you on there :) Did the formula work?

I need this for the Lexus ISF EU Facelift Model

@MotorvateDIY

3 жыл бұрын

I don't have any data on Toyota / Lexus vehicles.

Nice video sir, your video inspires me a little! I have a Question : How can I find that PID address? I'm really looking forward to find the PID address of SMART Fortwo, for display Engine Oil Temp. & Exhaust Temp.

@MotorvateDIY

4 жыл бұрын

Hey 김형직, I will explain the process to you.... but it is not a quick or easy process. I am not sure this will work for a vehicle from Europe, but this is what I do for Nissan vehicles. First you need to verify the engine has an oil temperature sensor and a exhaust temp sensor. If there isn't a physical sensor, the data doesn't exist. Use a cheap OBD scanner and Torque Pro. (here is a video from my other channel that sows the set up: kzread.info/dash/bejne/d4SI0biHoc26aM4.html) Then install the "Torque Scan" plug in. With the engine running, run Torque scan. This will scan the extended PIDs also known as UDS mode 0x22. You should read up on the structure and use of UDS modes. Now the hard part. You need to sort through the test results and look for a number that is slowly increasing. Since the engine is warming up, the oil temp should be warming up and the number should be increasing. Once you have the 22 xxxx PID number and byte position (there are 8) you now need to figure out the formula. From what I have seen most temperatures add 40 or 50 to the data value. So, to get the temperature from the data you need to subtract 40 or 50. As you can guess, it can takes months to figure this out.

@pezglobo2688

4 жыл бұрын

Motorvate DIY Really appreciate for your answer, I've read 3 times! Now I can understand, I’m going to try it first. Thanks!

Any gauges for oil pressures?

@MotorvateDIY

5 жыл бұрын

Hey The Sum Of All Parts, Sorry but no. Most Nissan/Infiniti engines don't have an oil pressure sensor, just a low pressure switch. The 350Z has an oil pressure sensor, but it connects directly to the gauge cluster. In a future episode I will show how to build your own digital oil pressure gauge using an Arduino and a nice OLED display for about $50.

Will this work with a Kiwi3 and the Torque based iPhone app? Looking to do this on my 2016 370Z which I am using as my track car. Or is this app Android specific?

@MotorvateDIY

5 жыл бұрын

Hey Jim Beaumont, The Torque app is only available for Android. However, you can use your Kiwi3 with OBD Fusion and purchase the $15 enhanced diagnostic add-on to see your oil temperature and 250+ other PIDs from the ECU (engine control unit) and all the other modules like ABS, air bag, etc) Here is a video from my other channel that give an overview of the $15 add-on: kzread.info/dash/bejne/i4iiutdyetfTmLw.html I am not aware of any other iPhone app that can show oil temp on a 370z. Good luck!

@gsstacker

5 жыл бұрын

@@MotorvateDIY Great, thanks! I did plug the Kiwi 3 into my 2016 Nissan 370Z and added the enhanced diagnostic add-on. One item of note is that if I connect using the ECS, a pretty standard parameter like Engine RPM is available but the gauge doesn't display anything. I thought that was odd as I can get something like Engine Oil Temperature and create a display for it but using the existing RPM display doesn't seem to work? Does OBD Fusion have any sort of support site or FAQ's?

@MotorvateDIY

5 жыл бұрын

Hey Jim Beaumont, What do you mean by "connect using the ECS,"? Are you trying to use Torque Pro or OBD Fusion?

@gsstacker

5 жыл бұрын

Motorvate DIY ODB fusion

@MotorvateDIY

5 жыл бұрын

Hey Jim Beaumont, When you mentioned ECS, did you mean ECM (engine control module)? That's odd, the RPM is not updating. You should be able to get the RPM from the standard Mode $01 pids. The next time I am in my car, I will have a look and see if I have the same issue as you. You might want to contact OC Tech and ask them: obdsoftware.desk.com/

Hello for opel astra h?

@MotorvateDIY

3 жыл бұрын

Sorry, but I don't know... Opel is not sold in North America so I can't reverse engineer it :(

Sadly it doesn't work for Qashqai R9M 2013 :/

@MotorvateDIY

5 жыл бұрын

Hey Tomasz Rzepka, Too bad, but thanks for letting me know.

Will this work for ls 6.0

@MotorvateDIY

4 жыл бұрын

Hey Al Al, Nope, this only works on 2007+ Nissan & Infiniti.

Can you also make one for Honda CRV. Please.

@MotorvateDIY

2 жыл бұрын

Sorry, I don't think I can... I specialize in Nissan/Infiniti vehicles/networks and don't know very much about Honda vehicles.

Hello, Can you please refer any authentic database of Proprietor/Extended PIDs of all manufacturers? Thanks!

@MotorvateDIY

2 жыл бұрын

Sure, here is the official list: www.etools.org/OEMLicensing

@MotorvateDIY

2 жыл бұрын

In re-reading your reply, I assume you are hoping to find this for free. I don't know of a list/database of all Extended PIDs for all manufactures. You best bet is to search the internet, which I suspect you have already done.

Doesn't work on my brother's Sentra Ser SpecV 06.

@MotorvateDIY

5 жыл бұрын

Hey Manuel Rivera, Thanks for letting me know... I did some searching and I don't think that engine (QR25DE) has an oil temp sensor.

this doesn't seem to work with obd fusion

@MotorvateDIY

8 ай бұрын

Nope, it won't, as the program doesn't support this method.

Is this the same step to get it in Fahrenheit?

@latino914

5 жыл бұрын

Never mind I saw that you Put the formula in. I was only able to get it one time when I tested it, but after that its giving me no response message. Double checked everything. I do have torque Pro and it is on the latest update. If you have any ideas about this thanks.

@MotorvateDIY

5 жыл бұрын

Hey Latino914, Judging by your profile pic, you are trying this on a nice white G37 Sport. (great choice!) I really don't know what that would happen, but maybe try deleting the PID and recreating it BUT this time leave out the formula. (just to test the communication) Then test it a few times. If the communication is good, add the formula, test it a few more times. If you have another OBD scanner, maybe try it as well. Good luck and let me know your resutls :)

@latino914

5 жыл бұрын

@@MotorvateDIY hey man thanks my car is actually the non sport. I just did the front sport bumper conversion. So it seems to work when I log out then log back into torque. But when I put it for display or try to retest it, I'm getting no response on the retest and no data for the display. Weird huh. Only reason I'm interested in this data is because I recently got a low oil pressure light on my car when only @ idle. But after 2 days the light went away. I know this data is only for temperature and not for pressure, but thought it was an important feature to have either way. Anyways thanks for your help.

@MotorvateDIY

5 жыл бұрын

Hey latino914, That is weird. The only other thing I would try is a different OBD scanner. The VeePeak ones have worked well for me and are good quality. As for your low oil pressure light, more than likely the oil pressure switch is malfunctioning. Based on testing on my car, the low oil pressure switch will turn on the light when the pressure is less than 5 PSI. In you case, if that was the case, you would also have VVT (variable valve timing) troubles codes. Just in case you have seen this video on how to check your oil pressure: kzread.info/dash/bejne/X32jmNSyqLqspLQ.html

Real good video! Do you have the PID for Oil pressure? That would be very useful.

@MotorvateDIY

4 жыл бұрын

Hey 冯展鹏, As far as I know, for Nissan's and Infiniti's very few have an oil pressure sensor. The 350z is the one exception that I am aware of and it wired directly to the triple gauge controller.

@user-rr3el9lu7b

4 жыл бұрын

@@MotorvateDIY How about transmission oil temp sensor? Did Nissan and Infiniti have it?

@MotorvateDIY

4 жыл бұрын

Hey 纯情豆腐花, I am working on reverse engineering the transmission oil temperature right now for the CVT and step gear transmissions. It is not difficult, just very time consuming. You will see a video here once I find it :)

@isdykelee

4 жыл бұрын

@@MotorvateDIY Please try pid 22110c with header 7e1 and equation A - 40

@MotorvateDIY

4 жыл бұрын

Hey Aiste Kojelyte, Sorry, but I can't... I have a manual transmission.

If the ecu doesn't support it, how does it get the temp?

@MotorvateDIY

4 жыл бұрын

Hey EDGGINFOOLS, Not every ECU needs the oil temperature. Most (not all) engines that have engine oil controlled variable valve timing, usually do have an oil temperature sensor. On some ECUs they have a "thermal model" and calculate the oil temperature based on start up temperature from engine coolant and/or air intake temperature, engine run time, engine RPM and engine load. This is also done to calculate the catalytic converter temperature.

@EGGINFOOLS

4 жыл бұрын

@@MotorvateDIY Cool information. Thanks a lot. Is there some way or website to learn further on how to set up the hex values and things?

@MotorvateDIY

4 жыл бұрын

Hey EDGGINFOOLS,, I wish there was a website for this.... but I haven't found one :( Most of the information about enhanced PIDs are from reverse-engineering, AND they are specific to a specific engine. So, this information is difficult to come by.

engine oil Mercedes w211? please.

@MotorvateDIY

4 жыл бұрын

Auto Gaz Serwis Gołańcz, Sorry, but I don't have that information. I did a quick search and didn't see anything that was confirmed to work.

Tendrás pid presión de aceite para un Audi A3 2009

@MotorvateDIY

3 ай бұрын

Sorry, but I don't have anything on any Audi vehicles.

How can we get transmission temp gauge for the 7at guys

@MotorvateDIY

4 жыл бұрын

Hey Jonathan Ortiz, I don't have access to a 7AT for testing :( BUT, I have been told OBDFusion with the $15 Enhanced diagnostic will show auto trans fluid temp.

@ortizjonathano

4 жыл бұрын

@@MotorvateDIY thanks .. so much i will try it out and let you know

@MotorvateDIY

4 жыл бұрын

Thanks!

What about obd2 Honda civic ?

@MotorvateDIY

5 жыл бұрын

Hey Süleyman Çakır, What year Civic and with what engine? Not all Honda engines have a oil temperature sensor and if there isn't an oil temp sensor, there is no oil temp PID.:)