I just did mine on a 13 1500 silverado. Didnt disconnect anything it can be done but its tight. Thanks for the video amigo

@opulence_prime

13 күн бұрын

How did you get that darn cap with the wires that connects to the sensor off? I’ve given myself arthritis just trying.

Excellent. Thanks for the vid. Gotta do one on my Hummer H2 as it may be the source of an oil leak I have. I hope it goes as smooth as yours did. You made it look real easy. Thank again.

Good job bro guys like you are what makes me able to accomplish my own work!!! Thank you

I’ve got this same dang problem with my 13 6.2 Denali… looks fun lol

THANK YOU FOR THIS VIDEO! I just did this today on 2011 Avalanche. Took me about 4 hours. Problems I had. 1. Getting fuel line off. 2. Electrical connection plug on sensor was a bear. There was a gray colored u shape tab that has to come up about eighth of inch to allow tab to push in and release connector. 3. Next problem and for me the hardest. The darn sensor was so tight it took a lot of effort to free it. But once that sensor was removed, I used a bolt to thread in the hold and catch the insides of the filter. Then pop that out and use same bolt threaded into new filter to provide a pushing rod for new filter. It will pop down in place in the hole and then I hand threaded the new sensor in. I'm not a mechanic but I am mechanical. I did it. I bought a special deep well socket with thin walls. Had to disconnect the end of one hose and disconnect fuel line ( use special tool) and remove the evap hose completely. Hope this can help someone else. THANKS AGAIN! YOUR VIDEO HELPED A LOT!

Thanks for the vid replaced mines today using this concept

Thank you so much for sharing your find. I was concerned about my engine. You have helped me tramendously. Blesssings upon you😊

Thanks so much for the vid. Just did this job without taking off the intake using your technique. I had to change a bad lifter 2 years ago on my Denali so I know how long the intake takes. Longest part was getting the oil pressure sensor connector off. 👍Thanks again!

@marypete7580

Жыл бұрын

How do you take it off? Is there something that releases so it can unplug?

Interesting idea to unbolt the transmission mount to provide some extra space. One should know that I watched quite a few KZread videos before starting, but still had to lay towels over the engine, use a stool, and do some of the work left-handed. I was able to remove one end of a plastic tube at the rear of the engine for more clearance. I did not remove a second tube or the fuel line at its connection. I broke off the gray "protector" on the oil sender harness connector with a screwdriver, and with left hand pushing a long screwdriver against the connector tab and right hand on the connector, I was finally able to release the connector from the oil sender. The special 1 1/16" oil sender socket I bought like 25 years ago did not fit over the sender, I used a 27mm deep socket. Then I used a 1/2" wobble extension, about 5" long, and that was not easy to push into the 27mm deep socket, but the socket had to go on first. Then I used a stubby 1/2" drive flex ratchet to unscrew the oil sender. Of course once that was unthreaded it fell somewhere so that took 15 minutes or more to find & remove. So I went to O'Reilly and bought PS508 oil sender, which actually did fit my special socket (but I still used the 27mm deep one). So with the new sender (I did not even try to find if the engine had a filter screen, I didn't feel one) purchased, I tied a piece of twine around it it case I dropped that, and screwed that in a few turns with my left hand. Then I put the 27mm deep socket over that, then the wobble extension, then the stubby flex ratchet. 15 minutes later I had that screwed in, and actually in similar orientation as the factory one. So 10 minutes more to remove those tools without dropping them. So 15 minutes later I was able to blindly turn the connector to correct orientation to snap that on. I re-connected the one plastic pipe I had removed, and started the Yukon: no oil pressure displayed, and check engine light was still on. So I disconnected the battery, touched cables together to erase all codes/clear computer, reconnected the battery, and started it up: all was working - SUCCESS !!! So even though The Cuss cannot fix everything, I was successful today. Yes, this took me several hours, but since I'd just ordered Mrs. Cusser 4 new tires (as the 5-year-old ones were quite dry-rotted), felt why not save $300 to $500 by doing this myself. Some mechanics apparently remove the entire intake manifold for easy access, but that's labor hours. For me, trouble with the special oil sender socket I had threw me for a loop, but the 27mm deep socket I had did save me. Realize that 4 different times I packed up stuff and quit, saying the mechanic could try his luck Tuesday, but The Cuss is a persistent little cuss, for sure. Mrs. Cusser is ecstatic, and promised to take care of me tonight....

EXCELLENT. This video helped so much. Thank you

Awesome video!!!!! Thank you. Few scrapes and bruises but well worth it 😊

Awesome very simple and informative video sir. I'm gonna try it tomorrow

Well explain. Most times I have disconnecting the lines.

Good on your wife. Pretty sure mine doesn’t know what a gauge is.

This sure helped me! Thanks!

ok heres the dealio. Was raining out so I went and got the sending unit with a lifetime warranty, instead of the 1 1/16" get a 27MM deep socket. SAE will work but it is a metric. SO, on the H2, all I had to take off is the cover. Did NOT remove any hoses. I tried before removing and it was possible. Literally it took me longer to gather up the stuff from my other front end project on my duramax. Probably end to end about 15 minutes. SO, i replaced it, managed to get it plugged back in and started. NO pressure. So, unplugged thinking maybe i screwed up a wire inside the plug, checked both and they were fine. plugged back in AND THIS TIME, unplugged the battery and let everything reset. Started again and it worked perfect. Kudos to you guys, both of you that tried it without taking off the intake.

Thank you very much....! I have 07 Ext Escalade with the same problem...

Great job

Good job I will try mines this weekend ! Appreciate it

Great video very helpful

Another tip would be to unbolt the rear transmission mount. Lift the transmission in order to rock the engine way from the firewall a few inches. Gives you more room to work.

@manbearpig2164

4 жыл бұрын

Have you done that on this type of vehicle, do you need to disconnect the driveline

@atxjax1

4 жыл бұрын

@@manbearpig2164 Yes. I did this on a sierra AWD. I just removed the two bolts for the rear trans mount and jacked the rear of the trans up until it hit the trans tunnel. This gives you about 2 more inches to work by the firewall. i didnt have to disconnect anything else at the engine. used a 27mm deep well socket.

@JeffCloudDesign

3 жыл бұрын

Jackson Cruz did you disconnect driveline or is it enough flex to be ok?

@atxjax1

3 жыл бұрын

@@JeffCloudDesign no need to disconnect anything else. Just unbolt the trans mount at the cross member and gently.jack up the tail end with a block of wood and a jack until you feel slight resistance

@JeffCloudDesign

3 жыл бұрын

Jackson cruz, you are a genius sir. Thanks. Wife bought a really nice 13 Escalade and I’m working thru a couple issues. One power running board motor replaced , now on to the oil sending unit and a new driver side motor mount

dude that rocks. Had a H2 mysteriously stop registering oil pressure I suspect the sending unit as well.

@kirbharp2157

4 жыл бұрын

How did it work out with your H2? I just got my part today so I'll be tackling it tomorrow.

Thank you.

I think I need to do the same thing good info

Gracias amigo gringo ☺️

There is a oil small filter underneath of the switch that you also should be replacing.

Thanks for a great how to video.

Its cold. Like 18degreesF, thinking I had to buy new gaskets take off intake, alternator yadayada. Dude...thank you isn't enough.

I saw on a video on replacing the afm with an aftermarket delete kit that the top plate on these engine has loose bolts, the guy showed himself unscrewing them by hand, so I would maybe suggest removing the intake manifold and ensure that those bolts are tightened to prevent oil leaks

Man I replaced this on my Denali it was literally torture it took me 6 hours the connecter that has the little tabs is what kicked my ass

I got caught with this in the dead of winter in Winnipeg, it was worth the 400

You don't need to disconnect any of those lines. Also, you'll want to replace the sensor filter too

Great video!! This helped out a lot but I did notice you didn’t check out the filter that sits below the sensor.

@johnbreeden5093

3 жыл бұрын

Fuck that filter! Lol

@nsboost

2 жыл бұрын

Check it? Fuck yank it out and don’t put it back in. Just another source of issues

Hello, can that plastic sound piece or heat shield whatever it is, can it be cut to asses the sensor much easier?

Can I go ahead and unplug the battery before doing this job and hook it back up once I’m done? Or must I do that part last?

I have a 2007 Sierra Denali with the 6.2L (L92) and I’ve taken pics and dug down with a pick and there’s definitely no screen/filter below the sensor. So I guess I save $6.

How tight do you need to tighten the sensor. I'm very worried about over tightening the sensor but also worried if it's not tight enough lol. Any suggestions?

@ddnevada771

4 жыл бұрын

David Samual Auto Zone told me 26 ft pounds. Good luck!

How do you remove the electrical clip on top of the sensor? I can’t see or feel what needs to be pushed, pulled, turned, twist and pull, turn and push? Wtf? Hours of attempts …. How about a pic with details how it works ? I cannot remove that clip

What’s your oil pressure at idle when hot?

@20tea

3 жыл бұрын

Mine is 20 psi...

Hey buddy 6.2l they come or they not come with filter my denali I just change the sensor but I never see filter inside .and I try to put new one but don't go all the way down

@josecast8667

Жыл бұрын

Same here did you figure it out?

Did you replace the screen before you put the oil pressure sensor in?

@robertopineda8740

2 жыл бұрын

I wonder if they did that and how could it be taken out with this method

What about the Filter ?

How do you release the plug on the sensor unit

@palerider6099

4 жыл бұрын

Pull the clip back and lift off at the same time .

You didn't replace the filter that goes with it, that needs to be done as well.

@SuperReverbious

4 жыл бұрын

If it's a GMC 6.2L, it may not have one. My 2009 doesn't - confirmed by dealer parts counter.

@palerider6099

4 жыл бұрын

My 2004 had none

@manbearpig2164

4 жыл бұрын

@@SuperReverbious I just did my neighbors, spent about an hour trying to find the filter, took pictures as good as I can, but I could not see it or feel it, I guess it doesn't take one, 2007 6.2

@illustr8phee100

3 жыл бұрын

07 escalade I didn’t see a screen...

@swthero

2 жыл бұрын

My 2007 Denali didn’t have a filter had pick inside trying to pull it out and notice there was none. Does it matter that the screen is not there?

You forgot to take out and replace the screen filter that's inside of there.. sits just below the threads

@robertopineda8740

2 жыл бұрын

Can you still take it out with the intake on? I'm assuming you can.

What no filter change 🤔 might have been a bunch of work for nothing without replacing that little filter under the sensor

@scoth2244

3 жыл бұрын

I agree. I would replace the screen that’s under the sensor too. If the screen is clogged then no pressure will get to the sensor. Just use a pick to pull the old one out. They are like $5.00. I also set a moving blanket on the engine and just laid on it. Glad it work for him and it’s a good video.

What exhaust u running

@ddnevada771

3 жыл бұрын

Just stock.

you forgot to change the screen?

My 2008 denali showing 0% engine oil life i just change the oil

@samyls3239

3 жыл бұрын

Reset the percentage

@tonykramps420

2 жыл бұрын

Has nothing to do with oil pressure.

How come no one is replacing the filter!!

@prestonbuss7967

2 жыл бұрын

Right

Omg! Why a mechanic charge me 200 to replace this 😳

Please do not wear rings on finger while working on anything electric or mechanical.... Very very dangerous....😐

Hate the shit lol

Took me 35 mins...no biggy