I've been searching, for a easier way to read, diagnostic codes, on the early Ford's and Mazda's. This is a great idea, very clever. Thanks.

As a subscriber to the retro channel I got quite a surprise to you see you popping up here (didn't know you had an older channel, I ended up here because I have the same port on my Ford Laser 2002). I guess our population of nerds in this country is small, and we'll all run into each other eventually

You didn't show the pin match up?

Hello! I have some cuestión and that is, with torque app i can see the fuel consuptiom? Ando the other cuestión is about adapter that i see in aliexpress, yo 17 to obd2 do You think it Will work ir conect yo that Port?

I have US MECS-II type. So if I connect only 3 wires ( +B, GND , MEN) according to your video at 3:42, it should work like yours, except you use 4 wires because yours is EU MECS-II?

Hi, saw your video, I have 1993 929. can't find what protocol it uses. also pins i have to use for OBD2. do you have any idea? I searched online but have no luck. I will appreciate your help. I have repair manual, but it does not have all those details either. thanks.

My would you be able to tell me what PIN numbers that is on the obd1 for the OBD2 on the Mazda thank you

Do you think this would work on the diagnostic port on a Mazda rx7?

Hi, I've got a ford escort mk6 equiped with a 60 pin EEC IV, its got a obd2 connector, but doesent connect to the pcm. On the obd2 has pins 3,4,5,7,11 and 16, with the ELM 327 desent connect with none of the protocols, I know the comunication pins are 3 and 7. Where should i conect them to the elm 327?

Is pre obd2 not the same as obd1?

wonder if this the same for b2500 or courier

Can you til me how to put the wires in the obd2 please

Can read water tem and fuel level boss?

Plz tell me about coure ef-de 660cc

Whats with all the questions, hes was pretty clear where things were lol.

Can you send me the name of the obd reader.

How to match the pin

Hello brother, is this successful on Mazda 626-Otomatic 1992?

@Lufttygger

3 жыл бұрын

It should :) it works on my 1997 626 GF with OBD1

@volkanulusoy9099

3 жыл бұрын

@@Lufttygger Thank you, I try👍🏻

Hello, my mazda 626 year 1.994 OBDI does not have BUS and BUS- terminals. I have tried to connect it to my ELM in many ways but without success, will you help me?

@Sawickipedia

3 жыл бұрын

Sorry mate, my old ford is long gone and everything I know is in the video

@Lufttygger

3 жыл бұрын

Did you try the pin-out as shown in the upper right, with GND, +B, MEN? My Previous car, a Mazda 323 BJ 1.5 1997 could atleast blink out engine codes (shorted MEN to GND if i recall), and abs codes (TBS to GND) - this was from before i ever knew of wiring to OBD2 :) With that said, also pay attention to the lower right pin-out, it specifically says 626 GF 1997-1999 (which is my current car, and it works great for me with those 4 wires)

Will this work on a 96 f250 gas engine?

Hello, I have the following question. How do you connect an OBD1 Ford 7 pin to OBD2? FORD OBD1 7 pin connector, it is different from mazda

Can I get some help here ,I got a obd2 sensor but my car has the same diagnosis port as yours in the video ,so I got a 17 to 16 pin connector which fits in to the port fine but the sensor isn’t working still, so I’m not sure if it’s the wiring or something else ,any advice here

@Sawickipedia

3 жыл бұрын

It's quite possible the adaptor is not wired correctly for this case. I didn't know they were even available, hence why I just connected the wires directly

@Gab3ssz83

Жыл бұрын

Hi Mike, I also bought that adapter, and not working for me as well. Have you managed to make it work yet?

@bluebeard3478

Ай бұрын

I have the same problem as you I purchased a 16 to 17 pin connector plugged my sensor in and get nothing I have a 2004 Ford ranger XLT pickup diesel

Hi. Google changed my KZread settings and I can't read public replies anymore. Could you please send me your reply to mike maps re 17 to 16 pin connector. Thank you.

@Sawickipedia

3 жыл бұрын

It's quite possible the adaptor is not wired correctly for this case. I didn't know they were even available, hence why I just connected the wires directly

@angeloparis7963

3 жыл бұрын

@@Sawickipedia Thanks for that. I just found a Russian vid using this connector and it does work with a OBD2 scanner. Only about Aus $13.00 on ebay. Thanks again. I'm buying.

Pin outs 3:43

@TheTopCat650

2 жыл бұрын

3:43

@michaelh9667

2 жыл бұрын

@@TheTopCat650 bloody ripper!

For a MAZDA MAZDA 323 2.0 DITD WINE JMZBJ14R201159352 Engine code RF * can you give me 25-pin connector drawing (FSB, TBS, and all others) + The wiring diagram between the two connectors Will the wiring be valid for all troubleshooting, (brakes, engine ...) Thank you

lol. turd festiva.