Thank you so much for your videos

@CurmudgeonTransmission

6 ай бұрын

Thanks for watching them.

Subscribed

Thanks for this. I too have a jeep jk 3.8 2010 rubi. Its manual gearbox is making a strange noise when coasting with the clutch pressed in. The gearbox is also quite noisy in a cluncky kind of way i can clearly hear the gears meshing.Also after driving and everything is hot the gear lever becomes stiff and it becomes harder/heavier to shift if it makes sense. It also almost feels like thers a bearing free spinning when holding the shifter after shifting into gear with the clutch in. By looking at this video i cant really see what could be the issue.

@CurmudgeonTransmission

3 ай бұрын

As with any noise I would have to hear it to be able to make a suggestion as to what it is. Having said that, These seem to have an issue with developing an imperfection on one of the input shaft teeth. It will cause a knocking type noise. As far as the feeling in the shifter goes. I think you are just feeling the gear train spinning on the forks.

Fantastic! Got a part 2?

@CurmudgeonTransmission

Жыл бұрын

kzread.info/dash/bejne/p4Sms5SspZe0d7Q.html

What are the plastic pieces inside the bell housing where the input shaft and countershaft bearing go. One is white and the other is black

@CurmudgeonTransmission

Жыл бұрын

Give me a time stamp in the video so I can make sure we are talking about the same thing.

So mine is making a noise almost like a knocking sound at idle and when pushing clutch in it goes away. Already replaced throw out bearing and all of its other components. Put it all back together and it’s still making the noise. It makes the noise under load but if I let off gas it gets quiet. Should I be looking at the input shaft bearing next? Do you happen to have an email that I could shoot you a video of the noises I’m having?

@CurmudgeonTransmission

5 ай бұрын

Probably going to something with the bearing or input shaft. This one had a tiny imperfection on one tooth of the input shaft. You can send it on my Instagram. CurmudgeonTansmission.

@bjr2379

5 ай бұрын

Maybe it’s the shift fork and rail assembly?

Throw out bearing most likely

@CurmudgeonTransmission

8 ай бұрын

Was a small blemish on the input shaft.

Were they hearing the thrust bearing in the clutch?

@CurmudgeonTransmission

11 ай бұрын

If this is the one that I am thinking it is, it had a small imperfection on the input shaft gear. Not sure what caused it. Buffed the imperfection down and they said the noise was gone.

@garbinator09

10 ай бұрын

I just had my 05 TJ trans rebuilt. I have the BMS Sport Shifter. My shop guy did a REALLY great job and I am very happy with Him and my Jeep! Its old, I am old. Cruising the dirts roads exploring the moderate trails. As long as my pocketbook allows for. 😊

@garbinator09

10 ай бұрын

I was curious how the job went. As a subscriber to KZread I wanted to see how this operation went. Thank You doctor Tom! LOL ❤

@CurmudgeonTransmission

10 ай бұрын

@@garbinator09 It went well. Thanks for watching.

@LandonWilson88

6 ай бұрын

​@@CurmudgeonTransmissionmy jeep also is having a rattle while in neutral and clutch pedal is released, the rattle goes away at the slightest press of the clutch pedal. It also doesn't show up at a cold start but after 10 or so minutes of driving. Would you suspect mine could be an imperfection like this or something else?