Nissan Altima 2013 to 2018 Replace squeaking serpentine belt (DIY) save $290
Автокөліктер мен көлік құралдары
Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#belt #nissanaltimabelt #altimabelt #drivebelt #sepentinebelt #nissanaltimaserpentinebelt #replacebeltonaltima #2013altimaserpentinebelt #2014altimaspepentinebelt #2015altimaserpentinebelt #2016altimaserpentinebelt #2017altimaserpentinebelt #2018altimaserpentinebelt
Пікірлер: 18
The hardest part is the tight clearance for the 17mm socket getting on the nut. Thank you so much for your help.👏🏾
@RBTheMechanic
8 ай бұрын
Yeah
Besides the pin on the tensioner, take out the clips on the fender skirt, pull back the fender skirt and put it behind the brake rotor and use a deep 17mm socket on the tensioner.
This video helped me and my son replace his belt. Thanks man.
@RBTheMechanic
Жыл бұрын
Nice good job guys!!
This is the hard way to do it. there is a hole where you can turn the tensioner to match the hole put a allen wrench in the hole which holds the tensioner in position. put your belt on put socket wrench on that nut to turn tensioner pull out allen wrench release tensioner and your done.
@RBTheMechanic
8 ай бұрын
Oh yeah I will look in to that I know Nissan has it
You should run the car so we can hear the sound. It be nice to compare the sound my Altima is making to this.
@RBTheMechanic
11 ай бұрын
Sorry customer took the car already long time go old video. U have any issues u can ask me or post a video so I can hear the should maybe help u out or guide u what it seems like
Dude that belt so easy to put on 😂 Omg 😳
@RBTheMechanic
10 ай бұрын
Yeah
What will cause my belt to keep popping off and making loud noise at the top of it on the same vehicle?
@RBTheMechanic
2 ай бұрын
Belt pop off? Did u check for any jammed pullies or bad pully bearing could be possibility it will keep belt off if it’s loose worn bearing
Question- I have a 2015. It’s losing oil but no signs of a leak anywhere. No oil spots on the ground. I’ve even had the motor top end flushed out. Any ideas?
@RBTheMechanic
8 ай бұрын
Might be burning check the exghust outlet tip if it got black carbon build up. Try replacing pcv and switch to gtx castrol oil
@TheTruthIsBlurred
8 ай бұрын
@@RBTheMechanic both tips are black from carbon. Sometime when I start it, it puffs smoke for a few seconds. You think that’s a PCV issue?
@RBTheMechanic
8 ай бұрын
@@TheTruthIsBlurred it’s possibility pcv is the simplest and easiest step also for Hondas we have been using gtx castrol oil it helps tremendously
@TheTruthIsBlurred
8 ай бұрын
@@RBTheMechanic thanks for your time. I’ll go tomorrow and pick one up. I’ll keep you posted.