Super helpful!

Thank you man!

Hello so I got my new one and I love it however it can be tune better. Do you have a good tune file that you can share?

I can't get dji assistant to recognize my evoque. It opens my photos like I'm uploading videos.

Great explanation man, just starting out with my Nazgul Evoque. Hope I won't have too many problems 😅 P.S: which version of the dpi assistant am I supposed to use?? The 2nd version is discontinued and I can't find another one...

I could use a refresher on how to configure the controller, Ang,Horz,Acro modes. I know that's a BF thing, but still, would like to see a video.

just wondering.. the button for binding the dji air unit to the goggles is it behind the lid (for the usb c port) or is it the small gap just beneath the letters HD? i think i messed up with trying to connect the tbs crossfire had to disassemble the bottom part to get to the receiver.. got it to connect but after assembling it back i only get one bleep when i plug in the battery instead of the whole array of bleeping its supposed to do...

@IconicProps

2 жыл бұрын

The button for the goggles and the controller is at the rear of the quad. Theres a usb c port and a hole below and towads the back. If you angle the quad correctly, youll see the light turn red inside when you press it. Use something non metal. Like a toothpick.

So I did everything in this vid. My drone won’t fly. Do I connect to the fc to setup transmitter inputs? Or the dji unit?

@silver.spec.b8588

2 жыл бұрын

I’m getting video and green light on my transmitter.

Hey so I have everything binded. together but my drone wont respond to any movements on my controller. It says connected on the headset and connected on the the remote after pairing. Please let me know cause this has been stressing me out for the last few days!! Thanks!!

@Cinoo90

Жыл бұрын

did you fix it this? I have the same problem ;/

Hi mate, what’s the antenna connection? SMA or RP-SMA? Planning to upgrade the antenna but I haven’t received my evoque yet.

@IconicProps

2 жыл бұрын

The antenna is a standard SMA coax connection. The antenna on the drone isnt as big an upgrade as getting the lumineire patch antennas or nubbies.

my drone if i accelerate a little, it raises the acceleration to the maximum by itself, without propeller, is this normal without propeller?

@IconicProps

Жыл бұрын

Yes its normal. The gyro isnt sensing change so it tries to keep adjusting and adding throttle.

I ordered Nazgul5 f5 evoque deadcat hd gps. But its receiver is TBS Crossfire Nano RX. I have a DJI goggles. Is it possible to connect them? I need another part to connect?

@royofzo4698

Жыл бұрын

the TBS crossfire nano RX is a radio receiver, not a video transmitter. You cán order a nazgul with with a cadx vista (wich is a dji video system) that is compatible with the dji goggles v2. In order to be able to fly the nazgul with the crossfire receiver you will need a radio/controller that uses the crossfire protocol. You can look up on google wich radio's are crossfire compatible. Unfortunately the DJI controller that comes with the dji fpv is not crossfire. As a matter of fact that controller is only compatible with the dji fpv and more recently the DJI Avata

@FPvPixels

Жыл бұрын

@@royofzo4698 I'm having major problems trying to bind the dji fpv v2 goggles to the drone flight board (via link button ) I have everything set up properly as in tbs agent desktop & the controller is binded to the tbs crossfire (im using tbs tango 2) i have dji assistant fpv 2 and have tried multiple batteries and waiting for the bind , im not sure what im missing, if youre able to help that would be awesome lol

Hi I can’t get my drone (like yours) to bind with my dji V2 goggles. The radio was no problem. I have the dji fpv system so I just got the drone and radio and was told I can use my goggles so I don’t have to buy another one.

@IconicProps

2 жыл бұрын

Did you single or double click the goggles? Make sure you have both on the latest firmware. 1.6x I believe.

@hobie278

2 жыл бұрын

@@IconicProps Thanks I got it going.

Is this the PNP version?

How is the range on the Nazgul with the DJI controller, I am torn whether to purchase a Tango 2 and then get the crossfire version, or just go DJI only.

@Lachlanrocca

2 жыл бұрын

I went tango 2 and crossfire. All the research i did pointed toward crossfire. Latency can be an issue with dji and better range on crossfire i've heard as well. Should be getting my controller and nazgul in the next couple days.

@IconicProps

2 жыл бұрын

From my experience, your video will go out before the TX. So adding crossfire won't do much. Unless you really like the controller better. That being said I purchased the lumineir nubbies and my range got better. Line of sight, I have been out 800 to 1200 yards. I can fly it 100 yards or so away in and out of concrete parking structures, which is about as far as I like to go.

@KhawajaTalha

2 жыл бұрын

@@IconicProps I ended up getting the crossfire version and a tango 2. So I read it's better for penetration. And range for sure I have the DJI still for other quads. So let's see

@Lachlanrocca

2 жыл бұрын

@@KhawajaTalha aye hope you're enjoying it :)

@IconicProps

2 жыл бұрын

@@KhawajaTalha the response is definitely better on the sticks but your video is still the speed bottleneck, but i suppise temwo way latency is worse than one way. Let me know hownit tuens out. I am thinking of trying a new controller.

nice video ! :) when i order the nazgul5 and iwill conect it with goggles i musst order it with bnf-dji transmitter when i will fly wiff goggles and the dji kontroler ? ty :)

@vei0vis

Жыл бұрын

Any help on this? I already got the DJI Googles but I want to get the Nazgul

@royofzo4698

Жыл бұрын

You need a different controller/radio than the dji controller that comes with the dji fpv drone.

Can you do a beta flight setup for beginners? I still own the cetus pro ( learning) the nazgul5 is going to be my first quad I own the dji fpv so I'll use those googles

@IconicProps

2 жыл бұрын

Most of the iflight quads have a good tune on them out of the box. The nazgul evoque was the only one I didn't care for, it was a little too fast. I will do a video that goes over the things that might go wrong. And what I do, but I am pretty new when it comes to tuning. I suggest the nazgul5 v1.5 (300 on amazon) or the v2 (375). I don't care for the nazgul as much as everyone else does. Its heavier. Thicker arms, but I have smashed all my quads into about everything you can hit and havent broken much. I just posted a video of the iflight nazgul5 with the skirtz, v2 config. And that thing is my absolute favorite now.

@IconicProps

2 жыл бұрын

I now have betaflight down pretty well. What I am about to say, will sound really dumb. but it is important. The hardest part is getting it to connect. The next step, is playing velocidrone. Pick a drone you like (I suggest the 533 or littlebastard). Fly it a bit, and get it so that you can fly it smoothly. You don't need to be great, just get proficient in navigating the level. (Coastal) Once you have that. close your eye, do a 180) open them, did you do a 180? Yes, you r rates are pretty close., No? Fix rates a bit (advanced drone setup). Once those rates are close, make sure you have betaflight 4.2 or better. Open up pid tuning. Set the settings just like velocidrone. You will be amazed that almost all 5 inch quads, will take those settings and fly similar. I am working on a how to train fpv skills. I made some huge advances in flying in about 5 days (day 45 ish) with some new training techniques I used. I wans to give them all out, from start to now.

i can't bind dji goggles

@IconicProps

2 жыл бұрын

So, bind the goggles first. To do so, turn on the quad, and press the button til it goes red (on the air unit). Do a long press on the goggle bind button. If it doesnt build do two firm, presses. You should see and hear it make a beep and go black. Hint. If you see black. Take the lense cap off.

6:13 MIC DEAD

@IconicProps

2 жыл бұрын

I will see if I can sort that out. Thanks for the heads up.