very very good dear friend!!!! thanks a lot !!!!!!!!!!!!!!!!!!!!

Great Job ❤

@ErCanEverything

Ай бұрын

Thank you my Friend🙏🙂🤝🤝🤝

Has the subscriber repair request series started? Awesome! 🎉

@ErCanEverything

Ай бұрын

😁🙂❤️

Great work! Is the 20 Ohm resistor a 0805 SMD package size?

Is it possible to snap the right pin from the Bluetooth chip to act preventively and if yes, which one of the pins without hot air station ?

@ErCanEverything

Ай бұрын

From the bottom right side the first pin is 3.3V. Cut it off. But first remove R44, change the 3.3V regulator and put a new resistor around 20 ohms

@AAAlexAlex

Ай бұрын

​@@ErCanEverything какой номер контакта блютуз ?

Good job ! 🙂 A bluetooth module in a battery! ..... Why not a hot drinks dispenser while we're at it!

Tutorial bagus sahabatku ❤❤❤❤❤

You are wonderful, my brother. I am an Arab. Should I take the same steps? Please respond

Have done the repair and at first it worked but after a few usages battery indicator lights only red even though it is at ~19V and it's not possible to charge/use anymore. Looked at the PCB and found no obvious issues. Resistor and voltage regulator are still working correctly. Have you experienced this? Any possible solution?

2:02 weeeeeee

@ErCanEverything

Ай бұрын

😁😂🤝🤝🤝

can you link the resistor

Resistors link please

How to repair blood pressure meter.❤❤❤

@ErCanEverything

Ай бұрын

🤔

i have two 8ah parkside battery locked with unknown pin how to unlock them ? any idea ?

Is that stabilizer also broken or is it just the BT module and the resistor (note to myself, also have a 8Ah Parkside battery, and still need to hear back from them after emailed them that my charger broke down after 4 times max use)

@pawelw.9172

Ай бұрын

the stabiliser is at fault, the same bL module is used in other equipment and works ok....

@Luke-san

Ай бұрын

@@pawelw.9172 Good to know. Well, will be ordering spare parts any way. Think I have them actually from ESP32 projects.

@pawelw.9172

Ай бұрын

@@Luke-san watch "elektrośmieciarka", you will also see a transil diode soldered in to protect the mcu.

@pawelw.9172

Ай бұрын

@@Luke-san wathc "elektrośmieciarka" the guy uses transil diodes to protect the "mcu".

@Luke-san

Ай бұрын

@@pawelw.9172 Been working with and designing electronics since the 80's, what world have we come to that we now need to repair this mess. Clearly design and quality issues. From my 3 Parkside orders, 1st saw failed after 1 go. Now my charger which was used 4 times is dead. Meanwhile the stuff that I build in the 90's is still running without issues.

another fix

I didn't understand why you removed the bluetooth modules

@apostolistimoleon1358

Ай бұрын

Because the bt module has a short.. that’s why

@ErCanEverything

Ай бұрын

Check description for detailed videos🙂

@apostolistimoleon1358

Ай бұрын

I have done the exact same thing to my own batteries. Now I'm trying to see what's wrong with the module..

@Iocreo

Ай бұрын

ok thanks for the answer@@apostolistimoleon1358

😮😮😮😮😮

💯💯💯💯💯💯💯💯💯💯💯💯

2:02 😅😂🤣

@ErCanEverything

Ай бұрын

😂😂😂

my friend how about ryobi bms repair

@ErCanEverything

Ай бұрын

I have not opened a Ryobi battery yet🤔

@nelchan2421

Ай бұрын

@@ErCanEverything I have not opened a parkside battery yet

Why does it have a BT chip anyway🤔

@ErCanEverything

Ай бұрын

I like the BT function but the first batch of modules have a problem unfortunately.

@pollywollydo

Ай бұрын

@@ErCanEverything but what IS the function ? All a bit new to this 🌝

Problem solved: eliminate the "smart" part of the battery.

@blackbird9813

Ай бұрын

😢

Have done the repair and at first it worked but after a few usages battery indicator lights only red even though it is at ~19V and it's not possible to charge/use anymore. Looked at the PCB and found no obvious issues. Resistor and voltage regulator are still working correctly. Have you experienced this? Any possible solution?