Thanks everyone for your patience this past month. This was kind of a quick video to conclude the Xbox Saga, and also get something out since I was sick for most of July couldn't record much as a result. But I've got some huge stuff in the works that I can't wait to show you all. Stay tuned!

@Cart1416

Жыл бұрын

You are early

@qwerty_studios

Жыл бұрын

i heop yoy are beetrt tlnow

@Pask___

Жыл бұрын

Hope you're feeling better now!

@qwerty_studios

Жыл бұрын

@@Cart1416 lol you are early

@Cart1416

Жыл бұрын

@@qwerty_studios I am probably like 5th

I’d like to point out the passive heat sink likely wouldn’t have worked because the two chips are probably not level with each other

@TrolleyMC

Жыл бұрын

True

@aprofondir

Жыл бұрын

Could've used some K5 Pro to account for that

@venialgaming4295

Жыл бұрын

@@aprofondir I'm not familiar with "k5 pro" but I assume it's some high quality thermal paste, it wouldn't matter because if there's any air between the chip and heat sink it will work very crappily and overheat, even if you put a dog shit pile-sized mound of compound on there it would negate the purpose because it would cool the chips so bad that it would be a waste of time, not to mention the paste would likely slowly settle, especially with heat, and stop making contact with the chip.

@RamyWarda

Жыл бұрын

​@@venialgaming4295 ​ You could use thermal pads instead of paste to deal with the die/substrate height differences since they're made in all sorts of thicknesses. The CPU runs at just over 20w with the GPU likely sitting in the 40w ballpark. Had to find pentium 3 733mhz/geforce 3 & 4 numbers, nothing easy to find on the Xbox- though total system power draw of rev 1.0 runs between 67-68w, with rev 1.3 between 62-64w so I imagine it's pretty close, so it likely shouldn't be a problem to keep cool with pads so long as there isn't too much of a gap between the die & heatsink.

@AstrumPuella

Жыл бұрын

@@venialgaming4295 K5 Pro is more viscous than thermal compound. It's more like highly thermally conductive silicone grease. Its purpose isn't just to fill the gaps between a chip and a cooler, it is a heat spreader itself. Covering the RAM chips on a GPU with K5 Pro is an example, as the K5 Pro acts as a cooler. But, it likely wouldn't be as good as a thermal pad in this case because K5 Pro isn't compliant with perfect contact when you have a gap of a few millimeters. Just use a thermal pad, and it would be okay.

“Ultimately it wasn’t a length issue, it was a girth issue” Yeah, I have that problem too

@dashtesla

Жыл бұрын

That was my last grindr date..

@Wheagg

Жыл бұрын

The most questionable thing MattKC has ever said

@originalpadoru

Жыл бұрын

@@Wheagg hey how’s the reception up there

@Wheagg

Жыл бұрын

@@originalpadoru not great

@BHNative

Жыл бұрын

I knew someone would think about their p on that one

You could probably 3D print some fan ducts like what they have on servers, and use the existing heatsinks. Those would guide the air to flow directly over the heatsinks

@AstrumPuella

Жыл бұрын

Ehh, unless he wanted to fiddle with higher temp filaments, then it might not be worth the effort. PLA wouldn't stand up to the heat and would soften quickly. PETG and ASA are kind of a bitch to print with if you don't know what you're doing. But if he were to go for it, it would definitely work well.

@georg6876

Жыл бұрын

@@AstrumPuella Printing abs is easy if you just have +40c ambient and a half decent hotend.

@zactron1997

Жыл бұрын

It might work, but the auxiliary components (power regulators, etc.) could potentially get starved of that airflow and start overheating. Worse, there wouldn't be a temperature sensor on most of those parts to actually safely shit the system down.

@tinyfluffs

Жыл бұрын

@@AstrumPuella PETG is pretty easy, ABS is decent if you have an enclosure, but those aren't all that common.

@BrunodeSouzaLino

Жыл бұрын

Too expensive of a solution. Just use thick paper or thin cardboard instead.

I installed a hydro fluid bearing fan (aka Hydro dynamic bearing) and set it to 100% speed. I just can't remember if it was a 70mm or 80mm fan. Over 10 years now of use and the fan is still silent and keeps the Xbox cool. You should look into these types of fans instead of using the basic ball bearing fans if that's what you are using to set it at such low speed on the fan so you don't hear the noise. At 100% with these types of fans it is very silent and effective.

@scikoolaid

Жыл бұрын

excellent suggestion. I don't think enough people consider using that type of fan to address noise levels

@Kholaslittlespot1

Жыл бұрын

Not sure I've ever heard of them. Interesting.

@chainswordcs

Жыл бұрын

I haven't heard of them either. (Given, I haven't ever done much research in the area)

@td1516

Жыл бұрын

Yes, they made a BIG noise back when I heard about 'em circa 2010-2014. Haven't really heard too much about 'em since but they do exist. The brand I went with was GELID (Silent series). I'm not sure if they are still around but it is what I used back then for OG Xbox's and also for PCs. Super Silent and effective.

@railpao

Жыл бұрын

Interesting, I didn't knew about it. Thank you !

I think it's possible, that the DVD drive might also have a little to do with the airflow, like with the HDD caddy, perhaps, you could try putting just the bottom of the drive back in and seeing if that improves Temps? That would only make it a little bit heavier, but might help (especially with the gpu heatsink)

"Are you tired of this Xbox yet?" "No" "Too bad binch" "Oh"

The SSD in my Frankly Horrific OG Xbox is held in with Gorilla Fabric Tape. Absolutely no clue how it’s held up so well with the heat.

@bluesillybeard

Жыл бұрын

Gorilla tape is for The Toughest Jobs on Planet Earth after all.

@thebassstream

Жыл бұрын

That's gaff tape I use that in automotive for bundling and protecting wire harnesses. Great stuff. Look at tesa's line of tape.

@tylern6420

Жыл бұрын

Flex tape would immortalize it

@georgewashington6171

Жыл бұрын

Budget bill

I'm a little confused, since you didn't like how the DVD drive cover no longer "floats" why didn't you leave the DVD drive in with its caddy and just have it disconnected? This would solve the soft whirring you were annoyed by. This would also allow the air flow to go back to what previously was the case and if you ever did want the DVD drive you could plug it back in (relatively) quickly.

@icedteaaddict4842

Жыл бұрын

I think another reason was to reduce the weight. Though I would suggest to open up the drive and taking out anything unneeded, but keep anything needed to make the DVD slot float.

MattKC: "The double sided tape for the SSD didn't work due to heat, I probably should've seen that coming" Also MattKC: "I used double sided tape for the Xbox logo, it doesn't go through anything so it should be fine" I don't actually know if that part of the case gets any airflow/hot, but I just thought it was funny :P Good work though, hopefully someday I'll do the same to a PS2!

@tspawn35

Жыл бұрын

The only mod a PS2 really needs is a fan replacement. The original is loud as heck. The original PS2 already has an external access drive bay just needs a network adapter to lock and interface the drive with the system. The other thing is you can get an rgb cable and an rgb to hdmi convertor. Lets you connect the PS2 to a modern TV. It also looks really nice without having to do any kind of perm mod to the PS2.

With the amount of space you have, you probably could fit a 2U cooler in there that would be a step up from the cooling you have right now. Suggest checking out some of the dynatron products for 2U server kit.

@brkbtjunkie

Жыл бұрын

Lol and 5x louder

@Heavy_Bob

Жыл бұрын

@@brkbtjunkie WHAAAAAAT? CANT HEAR YOU! I AM GAMING! *FAN GOES BRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR*

@Heavy_Bob

Жыл бұрын

Follow up, you might be able to use one of the xbox 360 revision coolers for your original xbox.

@Arminoderso

Жыл бұрын

@@brkbtjunkie just change the fan

@misham6547

Жыл бұрын

@@brkbtjunkie actually some 3U coolers are very quite like the noctua onr

You could also add a noctua 40mm on top of the cpu ? Airflow might still be good enough for the "OG" fan to work as an exhaust. And the noctua 40mm are dead silent at correct speeds

@nathanmead140

Жыл бұрын

In front would be better

I'm not sick of these videos. I love them. All 3 of my xboxs have failing drives, so I have them lined up, ready to do these sorts of mods on all three at once. I'm glad I waited this long!

What an intro lol, legit made me laugh. Thanks Matt for making entertaining videos and teaching us in the process!

I would advise against relocating electrolytic capacitors willy-nilly, as they are often used for local decoupling and may well contribute to rare, obscure failures. Datasheets for most ICs will specify as short a length between decoupling caps and the Vdd/Vcc pin as possible. You can probably be more lenient with how long your connection between the negative terminal and ground is.

@thewhitefalcon8539

Жыл бұрын

They probably also specify ceramic decoupling caps. Currently people are using ceramic caps as close as possible, and electrolytics every here and there, due to their higher ESL and ESR but also higher capacitance.

@nikkiofthevalley

Ай бұрын

​@@thewhitefalcon8539With modern ceramics, you rarely need electrolytics unless you're dealing with high current transients, and even then you only need a few.

I highly recommend getting a bag of 20x20x10 mm heatsinks off ebay and some thermal epoxy (or at least an adhesive thermal pad) and putting one of them on the MCPX chip next time you're in your Xbox. It's right next to your modchip and it gets pretty damn hot. Due to easily hitting peaks of over 60 C in some situations and just generally going through some rough thermal cycles in its life, it's responsible for a lot of Xboxes dying. I am not sick of this Xbox- thanks to these videos I ended up buying myself a new one to replace my recently-FRAGged childhood 1.1. I hit pawn shop gold and ended up with a seemingly barely used 1.1, manufactured 4 days before my old one, with a stealth modchip already installed. I went for the exact opposite approach to this Xbox. 500GB IDE Caviar black, modified Wii2HDMI, heatsink on the MCPX, and for the ultimate in jank Xbox mods, I cut a hole in the plastic on the left side of it and zip-tied a fan to the metal chassis, pointed straight at the MCPX. It's loud as all fuck. I don't care, I have headphones. I watched my 20 year old Xbox die last year, and I don't intend to allow the same fate befall this one. Thank you for the inspiration Matt

@handlesrtwitterdontbelivethem

Жыл бұрын

did i ask

@AstrumPuella

Жыл бұрын

@@handlesrtwitterdontbelivethem why did you assume that the comment for MattKC's video was directed towards you, at all.

@HotClown

Жыл бұрын

@@AstrumPuella Hell the entire first paragraph is literally just general advice directed towards anyone with an Xbox lol plus I reckon most people who own an Xbox in 2022 probably love hearing about other peoples' Xboxes, I know I do so needlessly hostile

@generallyunimportant

Жыл бұрын

crossbox moment

Not too common to have a "girth" issue.

I looked into doing a combined Heatsink for both GPU/CPU in the past but each die has a different Z Height, so you would need a shim to adjust the height between both dies to get proper thermal contact.

The Noctua L9 cooler you reference at 8:11 actually blows the air DOWN, because it was designed to also cool the VRMs and associated components around a CPU. Depending on the clearance to the top shell of the Xbox it could still struggle to intake air, but it would exhaust quite happily around the board and get sucked out the back.

"I knew The thicker ones should fit, but just incase they didn't, I got a 1 level thinner too" * checks the comments *

Good to see sponsors that's related to the content! Make's them completely bearable. :D Also about the cooling, too bad you couldn't use a fan that's a lot like those found in a PS2 Slim... 🤔

I once had a low profile HP PC, and a tunnel was put on top of the top facing fan, solving the side outlet issue. :) You can print such tunnel easily with a 3D printer :)

I would advise that you still use the DVD tray/caddy in the Xbox. Even though the DVD drive is gone, it still provides support inside the console. I would also suggest modifying the tray in some way to help guide air over the heatsinks.

I'm honestly amazed by your patience. A while back I meant to replace the bulging caps in my Xbox v1.6 but getting them out was so much of a hassle (my soldering skills are dreadful and I don't have a proper solder pump) that I just kind of... gave up. Anyway, great video, love to see Xbox content!

@chunye215

Жыл бұрын

I thought the 1.6 was the one that doesn't have bulging caps. Or was that just wrt the clock cap?

@burretploof

Жыл бұрын

@@chunye215 The 1.6 usually doesn't have the bulging clock cap but it does have other caps that tend to bulge on that version. :( It's actually more of a hassle as it's more than one cap that needs replacing.

@nickwallette6201

Жыл бұрын

The clock cap leaks. The regular PSU rail caps dry out and swell. Here's a tip when desoldering caps that may be attached to large power/ground planes: Clip the remainder of the leads off so you have as little as possible on the solder side of the board. Add fresh solder. Don't try to evacuate the solder, just apply heat and work the cap out a little bit at a time, one leg then the other, until it comes free. THEN use your desoldering pump to remove the old solder. Sometimes you can't get all the solder out. That's fine. If you can clear one hole, great. Cut the lead shorter on the side that the hole is still plugged, and push the remaining lead through the clear hole. With plenty of clean solder on the plugged hole, heat it up while you push the leg (gently) through the other side. Be careful not to bend the leg. It helps if it's short (like 1cm or so.) If both holes are stubbornly clogged, you may need to walk the new cap in a tiny fraction at a time.

Nuts, gerth? Snipping? Bent Legs?? This one had some innuendos, eh?

3D print ducting for controlled air flow so you can remotely mount the fan this way you can use a larger fan at a lower speed. You just need to minimize static in its design (minimal turns and narrowing). A fan doesn’t need to be mounted directly on or even near a heat sink they are just sold that way for cost and convenience. If all of its air flow is ducted over the item trying to be cooled you get the same effect. Much like how duct work in your home cools and heats the rooms without the furnace fan being in that room. I really wish I had an Xbox because looking at yours I’m visualizing a really interesting fan location that pulls air across the entire board but directs all of it over the CPU and GPU before it exhaust.

I was rewatching all of your videos. perfect timing!

It looks like there would be enough space to ad an intake fan, it certainly could help with temps. and as others have mentioned, fan ducts would be another way, to increase airflow over the heatsinks more effectively.

Hey dude, I just wanted to say that I checked out your music after it showed up on an end card and I gotta say that you've got a damn good voice. I didn't know what to expect but your really good at singing

0:02 "are you sick of this Xbox yet? Too bad, bitch!"

only issue i see is that dvd drive had the same effect as the hard drive cover it helped airflow on the gpu heatsink, now that it is removed its likely running much hotter. i would suggest making some sort of cover or something to help direct the airflow.

@ntnavy1

Жыл бұрын

yeah my exact though, i just leave a coment sugesting something like this. There's a lot of posibilites of what he can do with that extra space

@GoTeamScotch

Жыл бұрын

I just put the bottom metal plate of the DVD drive back into my Xbox after removing the drive.

Cool video! Have you considered a 128MB ram upgrade? I don't remember if that specific Xbox is a 1.6 or not but do know that it is possible to RAM upgrade a 1.6 now. Anyways, I think it would be cool

@Knightowl95

Жыл бұрын

Macho nacho did a video on upgrading the ram in a 1.6 xbox.

@TrolleyMC

Жыл бұрын

@@Knightowl95 ok and?

@chandlerbing7570

Жыл бұрын

@Birdinium - DW bro, His mom probably just yelled at him for being a discord mod and now he's taking it out on people

@MuchWhittering

Жыл бұрын

@@Knightowl95 So therefore nobody else should be allowed to do a video on the same topic?

@MuchWhittering

Жыл бұрын

@@chandlerbing7570 Wow, what a totally mature response to a perfectly valid comment.

Tbh I’d be all for watching some videos of you trying to watercool your Xbox. Tho as a retro game collector, seeing you remove the disc drive hurt 😭

@CtrlAltBacks

Жыл бұрын

These guys out here removing their disc drives and then my wii has a dead disc drive, my Xbox 360s disc drive is jammed in. Oh, by the way, as a fellow collector, do you play on your consoles and games?

@salamiwallnut

Жыл бұрын

@@CtrlAltBacks I also jammed a 360 drive once, but I shoved a screwdriver in the crack between the disk drive plastic and the shell, and somehow I fixed it

@PostalAngular

Жыл бұрын

Honestly, when I get old disc games I rip them as soon as possible so I don't have to risk degrading them or the drive. Though I do see how it kinda defeats the point of purchasing the game lol

yk matt, thank you for making content. there's something so soothing and relaxing about your videos, they just make me feel like all is well, hope you have a great day

i wonder if server heatsinks could make a good fit in that space.

For future reference a wood chop saw will cut aluminum. I recommend squishing the blades into some soft wood, or filling the gaps with some wood, and just chop it slowly. Then you would get the benefit of a taller heatsink.

I've done a low profile cooler, but I also cut ventilation into the top of the case, since the one I had picked up for modding had already been damaged anyway. That xbox ended up just being a case that I converted into a mini-itx pc case, and I transplanted the actual xbox bits to a new case of one that was water damaged beyond being worth repairing.

I love MattKC, I've been fiending for a new video. Always so much fun to watch. Also, it's been shown that you can double RAM now on ANY OG Xbox, if you're interested in trying it :D

One thing you could consider doing is using liquid metal thermal compound on the CPU. You can't mix liquid metal and aluminum though, so you'd have to nickel-plate the aluminum heatsink.

I love the whirring sound of the PS2 and Xbox, combined with the startup logo sounds it's such a nostalgia trip :)

@UNSCPILOT

Жыл бұрын

Honestly considering finding ways to mod my desktop PC to sound more like 80's and 90's PCs, the silence kinda gets boring! Already started with a PC error code speaker so it has a chearful "BEEP" every time the bios boots and starts loading Garuda Linux, now I just need fans that get meaningfully loud while still doing a decent job and not nessisary sounding "bad" which will be more involved. Oh and making something that emulates old harddrive noises based on the activity light on the case, which will probably be custom. Oh, and a floppy disk drive, because I found a old Sony Mavica FD75 floppy disk camera and can't resist the urge to play with such weird old hardware

@granite_planet

Жыл бұрын

@@UNSCPILOT Old hard drive sounds 😍

1:19 all five pegs are missing their center pin.

Careful with passive coolers, they assume you have convection based cooling, which wouldn't work for you either.

Hey Matt. Love your videos etc. In my car, there's a few plastic pegs/screws that hold various plastics in place (I think I'd bought some for my car a long time ago from AutoBarn, but they can probably be found elsewhere?), maybe those could work in place of those pegs here? It's a long shot, but maybe that might help...

I refuse to believe the saga is over until you add the 4 extra RAM chips.

Matt, if you haven't tried it I think you might enjoy using 3M VHB tape in some of your projects. It's strong enough that it's used for attaching dash cams to windshields, yet removes cleanly.

This is so cool I appreciate these vids man!

to cool your components, what you can do is use the noctua cooler you showed off and 2 noctua 4020 fans on the side of that cooler, blowing the air through the width of the cooler like you wanted it. it would cost some money because noctua, but it would preform like noctua.

@Mulakulu

Жыл бұрын

also maybe covering the area where the 92mm fan is with tape or something so the air blown from the 40mm fans go the whole way through

I thoroughly enjoyed it. I love when ingenuity is involved in your videos. I don't think anybody's tired of the Xbox I think we are all interested in seeing how we can make it better. So thank you

Thanks for another video about xbox. I really like your videos. Some suggestions for future xbox saga videos would be 128mb ram upgrade for v1.6 xbox which is now possible, a 3D printed shroud cooling duct (maybe retrofit the x360 phat cpu xenon heatsink, dunno if possible), and perhaps the holy grail P-III 1.4GHz CPU upgrade.

The best way to learn cad for 3d printing (I use fusion360) is to jump into a major project and break it down into smaller pieces. Watch a video or two on the basic features like UI navigation, and basic sketches, and joint components to create one big assembly of all the smaller parts you designed.

Hnng, please, this is your best series so far, watching you struggle with that green boy makes for great content! Please look in to server cpu coolers like Dynatron T318, and please just move those caps. Or replace them with smaller caps, and solder them in so then have long feet to move them far away. They do sell heatpipes on Mouser and other places, you can bend them, and they can move the location of the cooler

Wow!! I love your videos so much! This is a great start into my morning

Great video, I would say you can 3D print a fan holder for a noctua 60mm fan which is on thingiverse & you can also 3D print a bezel holder which can screw into the dvd holes 😉. Some have also 3D printed a shroud for the heatsink so that it pulls air closer to the gpu.

I actually really enjoy the Xbox videos. I'm pretty big into Xbox modding myself. I especially enjoyed the HDMI mod you did.

The hard drive caddy is part of the cooling system.. it directs airflow over the cpu heatsink. Without it, the fan can’t pull air over the heatsink

What SATA adapter did you use. I got the one that is widely recommended but still takes a while to boot.

Thank you for all of the Xbox videos!

What if you used an impeller? That would be low profile and would easily fit in the case. You often find impellers in laptops and such where you have a really tight form factor

A custom copper heatsink for each die would be better, you could get the same size and shape but better heat flow. Also having an extra tiny hole in the side of the case can mean a little extra air intake which could reduce temps

Hi Matt! I love these Xbox videos and I don't mind you making them.

What ide to sata adapter did you end up going with? I can only find the one that leads to a 40 second boot time.

could always add an intake fan on the side panel, hide the breathing holes in the grooves of the outer chassis, that could create an air channel to drop it by 5 to 10 ish degrees

there is a 3d print floating around for the fan and the dvd tray front panel, also if you haven't seen it yet there is a 128MB ram upgrade for 1.6 Xboxes. and evoX titan will support hdd's up to 16TB! and using a startech ide adapter you can use the UDMA 5 option for titan making boot times even faster! but titan only works on 2TB+

@matthewwilliams5258

Жыл бұрын

also if you arent using dashloader by rochy5 with evox you should it patches in xiso support on bot

Plastic pegs like that are used in car interiors sometimes, although often larger. But I have seen some that size. An automotive store might have them

Have you heard of, or are planning to do, the internal mod for the OGX360? I have seen designs to allow mounting and connecting it inside of the console. Having a USB port mounted in the crevice beneath the power button, with the OGX360 having daughter boards that allow the use of the original controller ports or the OGX360. Even saw a different version of it that has the Arduino components all on 1 board.

Now that the DVD drive is out, there is lots of room to mount a big cooler there. Something that is offset. Something nice with heatpipes to get all those Watts over there.

I snip out the metal grate that the fan pulls air through to help reduce fan noise an improve airflow.

Saying the saga is over is just jinxing yourself.

My old Xbox had a problem where the heat sink got disconnected and my Xbox overheated and it never turned on again

Would love to see building the ultimate Dreamcast next!

Love your videos Matt!

I'm loving the format of this video with the post-action commentary!

I enjoyed this saga very much. Next chapter : 3D printing. What ? Anything that could fit in there. An airflow guide ? Hardrive caddy that take the whole space and add that little thing that might help keep the Xbox logo in place ? An empty shell to replace the dvd drive ? The future of this Xbox is limitless.

The noctua heatsink you showed that blows air "up" actually blows air down and to the sides. But it needs air from above so you'd need a vent there anyways.

really enjoyed these Xbox videos Matt! any chance you could do the same to your GameCube you bought from Japan that you fixed last year?

The Noctua cooler would have worked if it fit, mounted, and made good contact. You can remove the fan from the top, and keep the regular system fan, and that will still give you a similar airflow pathing, just with a lot more surface area. The GPU likely wouldn't be able to contact it, so it would still need its own heatsink. The heatsink it has would probably still fit under the Noctua finstack, if not you could try to mesh its fins together with the Noctua finstack and see if that will transfer enough heat into the bigger heatsink to matter.

I love the og xbox content btw. Would never get bored of those videos!

New mattkc upload!! Brightens my day

That was the most full on To bad bitch :D that i ever heard

Hey Matt, maybe someone already mentioned this, but you could 3d print a bracket to mount your dvd face plate (or even 3d print a DVD faceplate with embedded bracket).

I expected the whole video to be about the SATA to IDE adapter alone, but I didn't expect the focus to be MORE than just that! Good mention about removing the optical drive, though I still wanna keep mine due to...unforeseen circumstances. Though I wanna see more. Try upgrading to 128MB ram and a Tualatin Pentium 3. I ain't tired of seeing the Xbox until you have done absolutely everything there is to do.

What "heatsink grease" did you use? I wonder if using a high quality thermal compound would help your temperatures - something like Arctic MX-4 or similar - along with enough of it to give good coverage of the CPU and GPU cores. That and using a 70mm fan with a better noise profile so you could run it at 100%.

Back in the day i modded mine with an 80mm fan. Have cut the caddy. But the best thing i did was add an intake to the DVD side. 70x15mm (IIRC). It really dropped the temps.

Removing the DVD drive and opening up all that space, likely reduced the air movement in the unit as well. Probably offset the difference by properly sealing the fan, otherwise, you may have had even hotter temperatures, without increasing the fan speed further. The drive is fitted to help with wind tunneling for airflow.

I was hoping to see a journey into the magical wilderness of immersion cooling. A fish tank, some pebbles, a little castle, and a whole lot of mineral oil!

all i wanna know. does this xbox pull in and thru the heatsinks and the fan blows it out? or does the fan blow the heat from the sinks into the rest of the xbox?

Which SATA to IDE adapter did you upgrade to? I also have the slow startup issue.

matt's the only channel i stay for the result instead of skipping because of how good his commentary is to me or he's just charismatic

I love this channel. I rarely have any idea what the hell is going on, but it's kinda like ASMR for me. Just his voice and passion is enough!

hey nice video, how about puttin a mini noctua fan NF-A4x10 FLX to the side of the heatsinks to make it closer to a real cpu cooler

Love these videos Matt

Great video but just remember plastic lugs were likely used to stop a short on the Faraday cage.

Do you have a link for “the better IDE adapter?” I have the same extended boot time with my current IDE adapter and would love to fix it as well.

Hey guys I think MattKC might have voided the Xbox's warranty by opening it up.

That's exactly what I did to fit a LGA2011-3 cooler for a LGA2011-3 processor on a LGA2011 motherboard (yes, they are electrically compatible, you just need a BIOS hack for a i7 5960K), I just used long screws and a peg.

Use the short fan that shoots the air towards the top of the case and 3d print a duct that reroutes that air out the back

I built a PC in an OG xbox case, for the DVD Drive door I used hot glue and it's almost perfectly centered.

I was searching for "silent xbox" and KZread recommended "silent xbox controller" WHAT

You could maybe make the optical drive cover some sort of grille to get more airflow, maybe even put a second fan...

Hey did anyone know a good place to buy modships for xbox classic and 360 ? THANKS!