That is an I/C Briggs and Stratton..., can not kill those easily !!! Best Engine ever made as far as I can see. That Engine I/C Series was the Best Line that B&S came out with..., my opinion!

@TufdogsPlace

5 жыл бұрын

I sold that machine a few years ago and it ran well til it finally broke down on the fellow. about a year ago. Thanks Jordan

@rannz8

5 жыл бұрын

I see you on literally almost on every small engine vid and other misc vids on fixing things like a/cs

This happened to me on a mower I recently acquired thanks for sharing.

@TufdogsPlace

2 жыл бұрын

Thanks, makes me feel a lil better, lol

You forgot to give attribution to those wonderful city workers!

Look @ 2:00 closely the Brake / Clutch Pedal and the Lever Speed is NOT Locked!

@TufdogsPlace

5 жыл бұрын

Yeah, I realized after putting this video out that I had forgotten to step on the pedal... Good eye You've got there... Cheers

@JodBronson

5 жыл бұрын

+Tufdog's Place - LOL ... Yea sometimes I do that too, then say.... What an idiot! LMFAO !!!

@TufdogsPlace

5 жыл бұрын

haha, yep, lol

When I try to start my mower it will make a thud noise flywheel moves a half turn then locks. what could be the problem Briggs & Stratton 12.5, I have checked all of these, battery fuse, spark plug, fuel and oil

@TufdogsPlace

8 жыл бұрын

Have you checked to see if your starter motor is secure, & not loose on the engine ? if it is take the covers off so you can see the gear on the starter, sometimes they go bad also. Let me know if this isn't the problem and we'll look deeper into figuring it out for you. Good luck

@INTERNATIONAL_RDF-D

6 жыл бұрын

Arlis K Hirsch could have something stuck to the magnets in the underside of the flywheel. I had this happen Engine would turn and stop and lock up Checked in the crank case Checked the head.... Nothing Finally pulled the flywheel off and found a broken bolt head stuck to the magnets... that was jamming Into the coil

what was the cause of the no start high compression? i have the same motor and im going thru the same thing..

@TufdogsPlace

10 жыл бұрын

No, I wasn't pushing the pedal down, so the belts are trying to turn the deck & tranny also causing to much drag. You can see it here. Tufdog's a Goof, MTD problems revealed kzread.info/dash/bejne/hZlhx5mels3VcbA.html Thanks & good luck,

@lawnside82

10 жыл бұрын

***** your EPIC!! that was my problem! my motor was turning the deck belt.. i dont have much slack in the belt even tho blades are disengaged..

@TufdogsPlace

10 жыл бұрын

lawnside82 Cool, glad that helped. yeah, I felt pretty silly after doing this again this year. Almost to the day too. lol I made a label that says "press pedal to start" for mine now. lol Cheers !

Hi sir, I like your work. Can you help me with Brigg and Stratton 13.5 hp OHV motor? It wouldn't start like yours. I adjust the valve with the feeler guage and clean the battery, terminal, all connection to the battery. Can you help me if you have time and day. Thanks

@TufdogsPlace

4 жыл бұрын

Have you checked to make sure you have spark ? & Gas

@shunkenshiro8511

4 жыл бұрын

@@TufdogsPlace to do that, sir, do I have to take out the spark plug and start the motor and see if the spark comes from the spark wire,? Am I right Sir

@shunkenshiro8511

4 жыл бұрын

@@TufdogsPlace gas is fresh Sir

@TufdogsPlace

4 жыл бұрын

@@shunkenshiro8511 Take spark plug out keep it attached to the wire, Ground the end of the plug to the engine. ( so that it touches metal) Do not hold it with your bare hand, (use rubber coated pliers to prevent you getting shocked ) And turn over engine and look for sparking in the plug

@shunkenshiro8511

4 жыл бұрын

@@TufdogsPlace ok do that. I will inform you soon. Thanks Sir

I am a licensed Briggs and Stratton worker please check your starter and battery mite be time to replace your starter

@TufdogsPlace

5 жыл бұрын

Thanks for the suggestion, turned out to be operator error. I was forgetting to push the clutch pedal and relive the belt tension. ooopsie, lol

can you fix my motor?

@TufdogsPlace

10 жыл бұрын

I may be able to tell you how to fix it. what's the problem ?

Sheared flywheel key...

@TufdogsPlace

4 жыл бұрын

Naw, it was operator error. I forgot to engage the clutch... Thanks for suggesting a fix though...

It’s called MTD that means many troubles daily

@TufdogsPlace

3 жыл бұрын

lol, Funny !

just adjust the valves to .004

@TufdogsPlace

10 жыл бұрын

I was looking into that & realized this is a flathead. So it's a whole different ball game. Still gotta do something though. Thanks for watching & the input I appreciate it