Awesome video! Thank your so much 👍

Tip for working in back of engine bay or anywhere tools, nuts or bolts can fall down. Stuff or lay a rag in behind to cover the drop so that anything falling will land on the rag and easy to recover. - great video and thanks for sharing your experience.

@FaithlessEmoRacing

Жыл бұрын

This is a very good tip! I did the same when I recently fitted a CoolerWorx short shifter. You have a hole in the middle of the transmission tunnel and very easy to loose things down there so i put a microfibre towel there to catch anything!

Just finished, thanks a million! Took me 4 hours or so. Last half hour was just me obsessing if I've tightened everything enough, alignment, if the silicone parts have been pushed in far enough etc. Happy with the sound. The increased noise noticeable than I imagined especially with a loud exhaust, but noticeable nonetheless and I'd do it all over again if I had to

@FaithlessEmoRacing

Жыл бұрын

Thank you for the comment. Check out my Santa Pod video for what happens if it’s not tight enough! 🥴

Thanks so much for the help installing this!

Instructions weren't great. Couldn't have done it without this video

@FaithlessEmoRacing

2 жыл бұрын

Thats great feedback and really helps me know im doing a decent job!

Installed this today. Greatly helped by this video. Doubt I would've been able to do it with the instructions alone. Thank you!

@FaithlessEmoRacing

Жыл бұрын

Thank you for the feedback! Glad I could help!

Installed today and this video was EXTREMELY helpful 👍👍👍 thanks mate That intake bolt was so difficult to remove lol

@FaithlessEmoRacing

2 жыл бұрын

I’m glad it was a help that’s why I made the video. And yes that boot was hard to get off. I almost gave up!

@RobertBaliva

2 жыл бұрын

@@FaithlessEmoRacing huge help! Yeah it literally took about an hour and multiple tools tried before I managed to get it out. Funny thing, once it moved a little I could remove it with my hands 🤷‍♂️

@FaithlessEmoRacing

2 жыл бұрын

@@RobertBaliva yeah I struggled and lost two ratchets. But as you said once it was loosened I did it with my hands.

@RobertBaliva

2 жыл бұрын

@@FaithlessEmoRacing haha yeah saw that in the video, glad you didn't edit that out as I was extra careful not to drop anything because of that. How'd you end up getting them out??

@arkofsalvation1

2 жыл бұрын

@@RobertBaliva I dropped my ratchet trying to install and it literally disappeared :(

Great video, nice and clear installation. The background music is a little loud.

@FaithlessEmoRacing

2 жыл бұрын

Thanks for the feedback, yeah I’m working on trying to get the right volume levels on the BGM.

Thanks for making this video. I have the All Type Fabrication intake coming and I was worried about those rear bolts being a nightmare too. 👍 Your intake sounds awesome!

@FaithlessEmoRacing

2 жыл бұрын

They weren’t easy to get too. The space is limited in the engine bay. I definitely advise to remove the stock air box and engine cover for extra room, then come in from the right side of the engine as you look at it from the front.

@LoftyVisions

2 жыл бұрын

@@FaithlessEmoRacing Duly noted, thanks for the tip!

That looks and sounds so good 😍 I was expecting it to be about £700 but it's about half that. Bargain

@FaithlessEmoRacing

2 жыл бұрын

Yeah I was really impressed. Seems to improve throttle response too and sounds great.

Great video, very well explained and not rushed.

Thanks for making this. Aiming to do mine at the weekend. Nice one

@FaithlessEmoRacing

Жыл бұрын

No worries. I hope this helps you do yours abit easier!

Nice sound. Shock it is on a standard bov. I imagine on Turbosmart or other it gives hell much better effect :)

Thanks for making this video!!!

Good video, thanks! Would like to hear it from stand still with the bonnet closed and a slow/fast drive by! 👍

@FaithlessEmoRacing

2 жыл бұрын

I’m hoping to sort a video showing that, weather permitting.

Did you ever have an issue with the vacuum module being deleted? I reverted back to stock intake cause my car kept throwing a check engine light because of that module being disconnected

Thanks for the video brother! Helped a lot.

@FaithlessEmoRacing

Жыл бұрын

Glad it helped. Thank you for the feedback.

I have a all types fabrications air box just because was fair price and Australian made and made quick delivery. Same basic information. Sounds great! I found the sweet spot to make turbo flutter haha build up boost better in 3rd 60km till you get the idea, and slowly back off the throttle and slowly. It won't activate the bov. Back off the throttle too fast it will let all the air out the bov Ps I have few videos of my sounds haha And also you can monitor the intake temps and charged air temps with a obd2 bluetooth device using torque pro app

@FaithlessEmoRacing

2 жыл бұрын

Yeah I have found that it does that in third easiest too. Tbh I love going half throttle and getting that induction roar, build a little boost then backing off. I want to get a OBD2 reader so I can read some of the info. It’s on the list of things to do.

I'll have to get one of these bad boys!

@FaithlessEmoRacing

2 жыл бұрын

Can totally recommend.

Interesting, thanks 👍

Thank you so much for this video, really helpful! I just fitted mine and ran into a few problems. The nuts that the maf bolts to are too tall and the oring doesn’t seat in the bore. What did you do with the part that clips into the main pipe behind the engine (you have to remove it and the lower M8)? Would you also mind clarifying whether you had to plug the vacuum sensor at the front of the stock air box after this video was made?

@FaithlessEmoRacing

Жыл бұрын

Which section are you referring to in the first section? If you put the time stamp on the section in the video I will figure it out. As for the vacuum sensor I left it connected to the old air box. Never had any issues in 10k miles.

nice video mate

looks great, you should do a Dyno test to see if it improves the power or does the hot air under the bonnet take away the performance, better still, get a grill and put it on the bonnet over the air intake, definitely get a little more sound and would at least get 3-5bhp. .

@FaithlessEmoRacing

2 жыл бұрын

I would love to do a back to back dyne test but just don't have access to one I can run the stock box and then change it over and run the MST one in the same day. But if I do see some time at my local dyno I will get it on there.

@lil50ist

Жыл бұрын

It does 12 to 14hp

Don't suppose you know whether the Airtec/Wagner/Foresight elbow will fit to the MST piping?

@FaithlessEmoRacing

Ай бұрын

I’m unsure. I’m hoping to try one sometime this year, funds willing.

Cool video I like your content I got your info today I was in the Mercedes iv got a bmw ordered and might have very soon was thinking of doing some comparisons etc and adding mods to my Mercedes might need some tips etc on how to create?! Thanks Dave

@FaithlessEmoRacing

Жыл бұрын

Hey there David. What BMW have you ordered? If you ever need any help with mods or tips then give me a shout on Instagram etc and im happy to help! Maybe even make a video!?

I'm getting my GR Corolla hopefully next month do you think this unit would fit on that car? Is that a tattoo of a pentagram on your arm?

@FaithlessEmoRacing

Жыл бұрын

This kit won’t fit the GR Corolla. But I’ve seen on the MST social that they have made one for the GR Corolla. Send them a message and say you saw this video and they should be able to sort you out! It’s not a pentagram, but a Heartagram.

@dougmaverick3287

Жыл бұрын

@@FaithlessEmoRacing thanks for the info you did a good install job very easy to follow. Did it make much difference in performance? Personally I'd much rather have a gr Yaris than the gr Corolla any day of the week I prefer small Nimble cars I used to own an Ariel Atom.

was the lady backing up in the land rover about to complain? :D

@FaithlessEmoRacing

Жыл бұрын

Lol. She didn’t complain, mostly was wondering what the hell I was doing!

16:45 if your just here for the sound

Great video! Question though, did you not have to refit the vacuum sensor that plugs into the connector you mentioned taping up? Just fit one of these kits to my GR and had a check engine light until I refit the sensor. Cheers! Keep up the good work

@FaithlessEmoRacing

2 жыл бұрын

Thank you for the support. That’s why I refitted the sensor. I know modern cars tend to freak out when any kind of sensor that was there isn’t fitted. That’s why I just taped it up and kept it out of the way.

@rbsmason

2 жыл бұрын

@@FaithlessEmoRacing Cheers, I interpreted the video as you just taped the plug up. Even during your sum up it looked like the sensor was on the desk with the rest of the removed parts but it’s good to know that other people reconnected it. As you say in your video the instructions aren’t the best. Did your car feel immediately faster once you had fitted the Whifbitz exhaust and this intake or did you only real feel the benefit once you had it mapped?

@thomasglover3834

Жыл бұрын

Any luck bro? Just guna fit mine today too

Hello! Thank you for this video! How's the car doing with MST Intake?? Problem with stock ecu? Does the engine run well? Carburetion problems or empty?... thanks you

@FaithlessEmoRacing

2 жыл бұрын

It's been a couple of months and one service later by Toyota and still doing great. Toyota didn't have a issue with it. No issues with the engine running, still pulls as hard as before if not harder. Zero issues!

@wildfishingadventures

2 жыл бұрын

@@FaithlessEmoRacing Very very well! 😁👍 MST is a good intake at good price! In addition to having no problems, it is also important to have a good power gain.. 😁 from the MST dyno tests the results were good! Thank you very much! I want it 😁👍 ... P.S: Happy New Year 🥂🥂

Nice video mate, does this intake give u much turbo flutter noises? looking into which intake to get and saw this video!

@FaithlessEmoRacing

2 жыл бұрын

Yeah you get some great noises. I’ve alway getting compliments on the sounds my car makes. If you hold half throttle in third about 3,000 rpm gives you a nice bit of flutter.

Hey mate, just got mine in the mail. Just to clarify did you plug the vacuum sensor back thats shown on figure 5 in the instruction sheet? I'm actually having trouble unplugging it and if I don't need to that would help me a lot haha. Cheers

@FaithlessEmoRacing

2 жыл бұрын

Just checked. If you see 5:02 in the video the vacuum sensor comes off with the length of pipe at that step. Hope that helps?

Like the vid. Have you seen the evolve intake?

@FaithlessEmoRacing

2 жыл бұрын

Yeah I watched the Evolve intake through its whole process. Its just too much money for me!

Thanks for the awesome video. Made my task easy.. How did you reconnect the vacuum sensor? Mine has the check engine light on and I still cannot figure it out.

@FaithlessEmoRacing

Жыл бұрын

Im glad i can help! If you check at 17:51 you can see everything i put away and the sensor was one of them! I didnt reconnect it and has been fine for the last 12,000 miles! maybe try a disconnect battery and reconnect?

Hello, do you leave the air intake control valve plugged in or remove it? I already have the Mst intake installed. I left the valve plugged in and the car shows an error on the diagnostics.

@FaithlessEmoRacing

Жыл бұрын

I’ve removed it. I’ve had no errors. You may get a error as the car can see it attached by not working correctly.

@lkr4973

Жыл бұрын

@@FaithlessEmoRacing Thanks, I'll try to disconnect. the problem is that the error cannot be deleted

Great video. How did you get these screws out behind the engine ? Mine are impossible to get them loose. Any tips please

@FaithlessEmoRacing

Жыл бұрын

They are tricky. My best advice is take the engine cover off (just pull off) and then come in from the right as you look at the engine.

@nkaradelis376

Жыл бұрын

@@FaithlessEmoRacing thank you so much. Tried all angles and they won’t budge. WD40?

@FaithlessEmoRacing

Жыл бұрын

You can try some penetrating fluid like WD40 to help loosen it. Won’t hurt. It is the bolt that almost made me give up!

Is the pfiew sound on shifts due to the filter? I always thought they where blowoff valve sounds

@FaithlessEmoRacing

2 жыл бұрын

The sounds are there already. But they are louder and more noticeable with this air filter.

Hey there 👋 it's good video .I get one set for my GR Yaris too. But I can't remove the intake hose as well , than I connect with Mst MAF sensor hose with original intake hose ..

@FaithlessEmoRacing

Жыл бұрын

I don’t think you can use the stock hose as it’s a different length and direction. I found removing the engine cover (just pops off) gives enough room to get done the back of the engine!

@tomimye1097

Жыл бұрын

@@FaithlessEmoRacing I connect with 4 inch silicone hose 76-89mm ,it's can install as regular but I'm know not the proper way.. hahaha

@tomimye1097

Жыл бұрын

But your video is help alot , better than manual instructions.. lol 😂 thanks again

When you installed the MST, did the engine brake on your car almost disappeared? I installed mine and the car has almost no engine braking anymore. And that feels very strange? 🤔 btw great video, it just took like 30min thanks to your video :))

@FaithlessEmoRacing

Жыл бұрын

I have not noitced any diminished engine braking since fitting the intake. Maybe a placebo?

@hamproMotor

Жыл бұрын

@@FaithlessEmoRacing I hope it is placebo :/

Did it feel like it gave more or less power, of did it just improve the sound? 🙂

@FaithlessEmoRacing

2 жыл бұрын

It’s hard to say without back to back dyno. I would say it seems more eager to pull than before though.

@kbb935

2 жыл бұрын

@@FaithlessEmoRacing Thank you! Im thinking of buying the same intake, so that's why I was curious

@FaithlessEmoRacing

2 жыл бұрын

Personally I think it’s a great intake for the money. Very well built and opens up the car abit more. Only minus point was the instructions were great.

@kbb935

2 жыл бұрын

@@FaithlessEmoRacing I think so to! Thanks for the reply 🙂

Did you fell a difference in power?????

@FaithlessEmoRacing

4 ай бұрын

I wouldn’t say I felt more power, but the engine felt more urgent and more willing to go! If you check Tegiwa’s video they back to back compare this intake and find good improvements.

Did you fit the turbo elbow or just the induction

@FaithlessEmoRacing

Жыл бұрын

The whole kit you see in the box. I don’t believe I had what’s is classed as the turbo elbow?!

@johnnyjames5628

Жыл бұрын

Ah ok. I've ordered the same kit but with the turbo elbow. Good video by the way. I'll be watching again when mine arrives 🤣

@FaithlessEmoRacing

Жыл бұрын

Well I’m glad this helps. If you get stuck. Reach out on instagram and I can always help!

how did you mount the camera for the incar shot?

@FaithlessEmoRacing

2 жыл бұрын

If you check my other videos you find one where I fit a seat mount from Tegiwa. That’s what I used.

that sounds great is that the standard bov too?

@FaithlessEmoRacing

2 жыл бұрын

Yeah that’s the standard BOV. I do have a Garage Whifbitz exhaust.

Awesome! Do you have a discount code?

@FaithlessEmoRacing

2 жыл бұрын

I don’t I’m afraid. Only a small channel. But drop them a message or email and say you seen my video and they might be able to help.

@sebbebo

2 жыл бұрын

@@FaithlessEmoRacing great content anyway 😄😄 got the ap carbon mudflaps thanks to you 😀💪

@FaithlessEmoRacing

2 жыл бұрын

@@sebbebo thank you for the support!

No music in background next time pls ;)

@FaithlessEmoRacing

2 жыл бұрын

Check out my other video which is just pure sound and no music.

Dump the stock music.

one of.the worst mechanic song