Hope you find this useful for your engine build thanks for watching
Жүктеу.....
Пікірлер: 20
@jgfpv31796 ай бұрын
Really needed this info bro for a minerelli build 🤙 much apreaciated
@keeganhache6667
6 ай бұрын
Glad I could help bro that’s why I make these videos
@mikemiller33036 ай бұрын
Thanks for the informative video 👍👍
@keeganhache6667
6 ай бұрын
Glad it was helpful!
@bryduhbikeguy6 ай бұрын
Thank you.I thought there were just 3 rods. I knew there was some differences in thickness of the weights,but not position of the rod pin.
@leonardarola5 ай бұрын
Short for the Piaggio, long for the 60mm Farmertec jug.
@zachtenbensel14404 ай бұрын
Some zeda-80 are 38mm. I never go off rod anymore. Only measure to know what you have.
@MotorizedChuck6 ай бұрын
What are the better engine case seals?? I replace my bearings with the 6202ks 3 thank you for that
@MotorizedChuck
4 ай бұрын
Viton I got them thru Smolik
@tmmedia10696 ай бұрын
hey man i have a question im getting a new engine because my previous 80cc engine blew up so im getting a new 100cc one im just not sure if it would work because my 80cc had 16:1 final drive and my 80cc had 44 tooth sproket will be using same sproket and chain 315 chain whatever it means and my 100cc new engine will be 18:1 transmision will this be compatible please help i may have more questions
@keeganhache6667
6 ай бұрын
Well as long as their both 2 strokes it should be fine there’s like 3 different 100cc kits on the market right now
@notsure20246 ай бұрын
Also 37mm cranks
@keeganhache6667
6 ай бұрын
Yup!
@tiger77776 ай бұрын
Thanks again Keegan. What is your favorite China doll engine.
@keeganhache6667
6 ай бұрын
Probably the 49mm iron sleeve cylinder because it got me into port work
@tiger7777
6 ай бұрын
@@keeganhache6667 What would recommend for me to get a new engine? I've had 2 BBR 66/80 that were good. 1 BBR 66/80 that l put 3cylinders and 4 different positions in and different mags and replaced ignition coil 2or3times and it never has run right a 4 different carbs (the ones that come with the kits). Have had the phantom, it lasted 48 miles and seized up. The 100MAX which ran great it just started getting hard to start after turning it off. And had a scratch in the cylinder and bicycle engines don't sell parts for rebuild.? The engines last 9 months to a couple weeks (not including the phantom which was 6 heat cycles and almost 1full trip to town and back 37 miles) are the zeda 80s any better than BBR stage 4 engine?
@tiger7777
6 ай бұрын
@@keeganhache6667 also, what is the 49 iron sleave called
@keeganhache6667
6 ай бұрын
@tiger7777 just get a Amazon engine put good crank bearings in it and don’t waste money on a engine with just a sticker
Пікірлер: 20
Really needed this info bro for a minerelli build 🤙 much apreaciated
@keeganhache6667
6 ай бұрын
Glad I could help bro that’s why I make these videos
Thanks for the informative video 👍👍
@keeganhache6667
6 ай бұрын
Glad it was helpful!
Thank you.I thought there were just 3 rods. I knew there was some differences in thickness of the weights,but not position of the rod pin.
Short for the Piaggio, long for the 60mm Farmertec jug.
Some zeda-80 are 38mm. I never go off rod anymore. Only measure to know what you have.
What are the better engine case seals?? I replace my bearings with the 6202ks 3 thank you for that
@MotorizedChuck
4 ай бұрын
Viton I got them thru Smolik
hey man i have a question im getting a new engine because my previous 80cc engine blew up so im getting a new 100cc one im just not sure if it would work because my 80cc had 16:1 final drive and my 80cc had 44 tooth sproket will be using same sproket and chain 315 chain whatever it means and my 100cc new engine will be 18:1 transmision will this be compatible please help i may have more questions
@keeganhache6667
6 ай бұрын
Well as long as their both 2 strokes it should be fine there’s like 3 different 100cc kits on the market right now
Also 37mm cranks
@keeganhache6667
6 ай бұрын
Yup!
Thanks again Keegan. What is your favorite China doll engine.
@keeganhache6667
6 ай бұрын
Probably the 49mm iron sleeve cylinder because it got me into port work
@tiger7777
6 ай бұрын
@@keeganhache6667 What would recommend for me to get a new engine? I've had 2 BBR 66/80 that were good. 1 BBR 66/80 that l put 3cylinders and 4 different positions in and different mags and replaced ignition coil 2or3times and it never has run right a 4 different carbs (the ones that come with the kits). Have had the phantom, it lasted 48 miles and seized up. The 100MAX which ran great it just started getting hard to start after turning it off. And had a scratch in the cylinder and bicycle engines don't sell parts for rebuild.? The engines last 9 months to a couple weeks (not including the phantom which was 6 heat cycles and almost 1full trip to town and back 37 miles) are the zeda 80s any better than BBR stage 4 engine?
@tiger7777
6 ай бұрын
@@keeganhache6667 also, what is the 49 iron sleave called
@keeganhache6667
6 ай бұрын
@tiger7777 just get a Amazon engine put good crank bearings in it and don’t waste money on a engine with just a sticker
@tiger7777
6 ай бұрын
@@keeganhache6667 thanks
Skyhawks are the best motors just my opinion