great video! 99.99% of us are amateurs too, so we are happy to see you doing such a great job! It inspires us to try also! Have a great 2024!

@AndyManCam

4 ай бұрын

Thanks very much Paulo. Give it a go, i say! It’ll only cost time and the vinyl really isn’t that expensive. Good luck!

Dude, I'm here about the bikes, the scenery shown, the little tech tricks....but man I love your commenting. Dude , you're simple, not coming from money and you like what you are doing. I like it.

@AndyManCam

2 жыл бұрын

Thanks mate. I really appreciate that! Thanks so much for watching!

I've wrapped a lot of bike parts in my day. EX250F, MT-03, FZ-07, Sportster X, Monster 797, few Groms and others I can't remember. Most of them were my friends bikes that I had the tools to do it. So I let them use them, and helped out. I'm not a professional to any extent, but I enjoy doing it. Tanks are always the hardest part. I do have some tips tho. Invest in a actual heat gun. It makes working with the wrap so much easier. You can pick up a cheap one at Amazon or a hardware store for $20-30USD. The difference it makes is night and day. I used a hairdryer for the Ninja which has a simpler tank than the MT. Yet had a easier time with the MT cause of the heat gun. I also use what is called cold stretching. It's were you use as little of the heat gun as possible. It is more time consuming, but you have less chance of the wrap warping. You can wrap stretch with just the heat from your fingers and friction. This will rub your fingers raw if you don't wear gloves, but I like to be able to feel what the material is doing. It's kinda up to you where and when you want to use the heat gun. Weird curves, line changes or to get bubbles out is the only time I use it. Hit the whole thing with the heat gun once you're done to make sure the adhesive is activated and you're good. I watched a vid from Adobo Moto and went to town. It's a little dry, but has a lot of good info.

@AndyManCam

Жыл бұрын

Cheers for the cold wrapping tip, i reckon i might give that a try next time. In any case i think I’m going to be shying away from patterned abs textured vinyls in the future!

Great job ! Now all you need is classic Honda badges 🙂

Full marks for patience and the end result ! I would have definitely thrown it out of the window……….and have done so with some tricky wallpaper in the past. So many different shapes and direction changes but such a lovely looking tank (sans badges 😉). Enjoyed that one, many thanks 👍

Amazed it came out as well as it did. I would definitely started crying half way through. 👍

@AndyManCam

2 жыл бұрын

Me too mate! I had my moments of considering chucking it down the stairs!

Would love to see it live. Good job for an amateur and a 1st time.

@AndyManCam

2 жыл бұрын

Thanks Marius! This was almost live! I left all the back and forth in for the torturous enjoyment of all! 😂

@MariusMutin

2 жыл бұрын

@@AndyManCam 😂

Fair play to you for having a go Andy, an admiral job! 👍

@AndyManCam

2 жыл бұрын

Cheers Mike. No risk, no fun!

Production quality on this vid was top notch as per usual. Keep it up mate :)

@AndyManCam

2 жыл бұрын

Thanks, will do my best!

Well done sir……. the tank looks amazing 👍🏻

What a great job Andy. In short, when we grow up we wanna be like you. Inspired!!

@AndyManCam

2 жыл бұрын

Thanks Doug! The pressure is on, if I'm to continue this role model thing! 😜

Good on you for giving it a go. 👍 Great vid Andy 👌

looks amazing🤩

Looks fantastic mate! You're putting ideas in my head...

@AndyManCam

2 жыл бұрын

Cheers mate! Go for it!

Pretty amazing considering the multiple angles.

@AndyManCam

2 жыл бұрын

Thanks mate! It was a bit of a disaster of direction!

I think it looks great. You are brave to take on a job like that!

Top job Andy! Looks awesome 👍🏼👍🏼👍🏼

@AndyManCam

2 жыл бұрын

Cheers mate! It’ll certainly do for the rest of this season!

Well done Andy, I would be crying and asking for my mum half way through any attempt at doing this. 👍

@AndyManCam

2 жыл бұрын

Haha! If it weren't for the cameras... ;D

my good god, i don't love any bike enough to try to tackle that manner of a faff job. Good on you for the patience and perseverance, better man than I.

@AndyManCam

2 жыл бұрын

Haha! I think that if it weren't for the videos and the resale value, I might have left it as well! ;D

Hey Andy, I think you did an amazing job for an amateur! I have spent a little time in the RC airplane world where I've also applied self adhesive stretchy vinyl, though not over anything so compoundingly complicated as that tank. Well done!

@AndyManCam

2 жыл бұрын

Cheers John! I'd possibly go as far to say that sometimes the bigger things are easier to wrap than fiddlier small things! That said, I'm not looking forward to attempt two on this tank!

Well done. I am impressed.

@AndyManCam

2 жыл бұрын

Thank you kindly Mr Brodin.

Good job 👍🏻 looks good on the bike.

You're getting good at these Andy! 👍🏽

@AndyManCam

2 жыл бұрын

Thanks! Maybe on the next one or maybe the after that, I’ll finally be happy!!

Great job!

You get my vote Andy.....great job.

@AndyManCam

2 жыл бұрын

Thanks very much Fitchy!

So THAT'S where the badges went. It looks good mate, well done!

@AndyManCam

2 жыл бұрын

All becomes clear! I think you'Re possibly the only person who noticed the missing badges in the vids though. Good eyes!

@mykheaton

2 жыл бұрын

@@AndyManCam well, I just bought a 75" TV lol

@AndyManCam

2 жыл бұрын

Haha! That’ll help! 🤣

I’m about to wrap a Superduke tank and you gave me some confidence 🙏

@AndyManCam

8 ай бұрын

Happy to help. Hope it went/goes well!

Good job!

Nicely done mate👍

@AndyManCam

2 жыл бұрын

Cheers Moff!

God this was hard to watch! It must have been so hard not to get cross and annoyed. You did a great job in the end. I would have given up and put it in the bin. Well done for completing it.

@AndyManCam

Жыл бұрын

It was, as ever, a challenge! This was probably the most difficult yet, so there was a fair bit of muttered swearing. Trust me though, the bin was always just a moment away!!

Looks pretty damn good!!

@AndyManCam

2 жыл бұрын

Thanks very much Craig!

You Sir, have more patience than me!

@AndyManCam

2 жыл бұрын

Many hours of swearing, fuming and ranting to reach that patience level! The struggle is real! ;D

Nice job 👌🏾

@AndyManCam

2 жыл бұрын

Thank you! 😊

Patience’s of a saint 😀. Mine would be in the bin 🤪.

Looks pretty good to me.

@AndyManCam

2 жыл бұрын

Cheers Tim. It'll certainly do for now!

Excellent work. I don't think you could have chosen a more difficult shape. Respect. Good old cable ties, so many uses. Ask Mrs Traveller. Looks really cool too. Kalpa! As we say on Kronos. Happy travels

@AndyManCam

2 жыл бұрын

You'Re right there! I told myself it would be easy while I was planning! But once on the table, it was way worse than first thought! Mrs Traveller sounds like a lucky lady! ;D

a brilliant job. the minor blemishes are barely noticeable. Well done you.

@AndyManCam

2 жыл бұрын

Cheers David! It really did look a lot better once on the bike, with all the trimmings back on too!

Hats off to you Andy for tackling that one, was it worth all the pain, it doesn’t look that different

@AndyManCam

2 жыл бұрын

Cheers Simon. Totally worth it. The reason i bought the bike is because i like that colour! This way i get the same colour, but in brushed metal effect while also protecting the paint from future scuffs and scratches.

Looking really good. De badging is definitely the right way to go.

@AndyManCam

2 жыл бұрын

Thanks Ian, I think so too!

Excellent job, more patience than me, love that tape but I would have paid somebody

Good Job don't be so Critical my self failed every year by wrapping Christmas gifts so be proud of your self

@AndyManCam

2 жыл бұрын

Haha! At least with this vinyl you get a few attempts before it's ruined! One slip with the sellotape and you have to start over with the christmas presents!

Great first attempt, cant imagine the patience that took .

@AndyManCam

2 жыл бұрын

Thanks Mark! My patience has reached monk like levels!

Looks good that mate.

@AndyManCam

2 жыл бұрын

Thanks very much mate! I'm happy for now!

Good results considering 1st attempt!

@AndyManCam

2 жыл бұрын

Cheers HG! YOu could certainly say that it went better than any of us were expecting!

@happygilmorides7353

2 жыл бұрын

@@AndyManCam I would have lost my rag 2 mins in and scrapped it!

Brilliant job U did anyways. I am doing my car right now, and it is the first time I'm doing it, and I have quite a lot of mistakes. But if you don't try it you will never know. And I will do my car again in the future just to get better at it. Cause it is a fun thing to do! 🤙👍💪 brilliant mate!

@AndyManCam

10 ай бұрын

That's the best way to learn! Glad you're enjoying it. I liked the finished result but HATED the process!! 😅

@1980thehammer

10 ай бұрын

@@AndyManCam the process is hard but after time you understand the vinyl. Not that I fully understand but I'm getting there. I must have watched 200+ hrs of vinyl wrapping videos by now. But I will keep up doing it. But it did look class on the bike at the end! Brilliant 🤙💪

Thanks for posting. You are a more patient person than I am. In my case, the vinyl would have ended up all balled up and in the trash.

@AndyManCam

2 жыл бұрын

My pleasure mate! Thanks for joining in with the torture with me!

Wow thats really impressive Andy! Top job!! Aaron Knox

@AndyManCam

2 жыл бұрын

Cheers Aaron! It turned out both better and worse than i was hoping/expecting!

You have done the imposible..i did not think that was possible..but you have done it..i have take the wrap throw it to the moon..

@AndyManCam

2 жыл бұрын

Haha! Thanks Mr Smith! It was a bit like looking at the soon to be scaled cliff face at the beginning!

Hard work!!!

@AndyManCam

Жыл бұрын

Very much so! That’s why i don’t do these vids very often!!

Look s good to me. It is a good idea the tank always seems to get scratched up. 😎👍

@AndyManCam

2 жыл бұрын

Cheers Garth. Absolutely mate. SOftest paint I have ever known! If only I could wrap the engine too!

You sir, have infinitely more patience than I!

Shaun (TheLikeableRider) get your hand in your pocket and buy that man a pint, a bet is a bet. Top work fella and like most things in life, they say you get better at it the more you do it!!

@AndyManCam

2 жыл бұрын

Hear hear! Cheers Mark! Next time will be a belter… maybe!

Great result Andy. Deffo the type of job I would have f****d up due to lack of patience… Enjoy that pint 🍺

@AndyManCam

2 жыл бұрын

Patience is definitely the key here! I blocked out the whole day for this job and had the kettle at constant readiness!

👍 I'd say that is excellent for a first go. 👍

@AndyManCam

2 жыл бұрын

Cheers Guy. Thankfully it wasn't quite my first go, but definitely my first attempt on something this complicated!

Brave man Andy. I don’t have both the skill or patience for that job. Looks good though. 👍🏍🇦🇺

@AndyManCam

2 жыл бұрын

Cheers Russell. You don’t know until you try! 😉

It may not be spotless perfect but you did a bloody good job, tempted to say much better than most of the so-called professionals. Double kudos mate! I'd have thrown the thing over the window ten times over ha ha ha.

@AndyManCam

2 жыл бұрын

Thanks JB. Simply the fact that I didn'T want to immediately tear it off was already a win for me! I'll try again when the bike is shored up for winter!

Hope you're not too disappointed with the job. At the start I'm thinking "no way". Amazed you got it on there at all. Looks great to me, and it's all good experience. Sure you'll get it to your own high standards if you have another go at some point. 👍

@AndyManCam

2 жыл бұрын

No, not at all. Once on the bike and with a Bit of Road dirt on it, it doesn’t look at all bad! Just don’t think it’ll last a winter. I reckon the next attempt will be better!

Seriously impressed with your patience. My concern is whether it will be worth it. I have my top box lid wrapped and it's not as hardy as I'd like. Fingers crossed for yours 🤞

@AndyManCam

2 жыл бұрын

Thanks Scotty. TBH, if it protects the tank from a few stonechips and scuffs, at it's own expense, then it will definitely be worth it. I'll probably feel like a change of colour/texture/design before the vinyl is toast anyway! :D

Thanks for the demo, I have a 2018 cb1000 and the tank is showing its battle wounds so I’ve considered a repaint. But this looks like a great way to accomplish the same goal. I have a heat gun, the kind used for striping paint. Or in my case as a pastry chef for removing bon bons from their casting molds. But anywho, do you think it would be too aggressive for this job, or a nice upgrade from a hairdryer? Anyway great channel, I’m enjoying all the cb content. I think I’m going to get some of those sw foot pegs you installed on the cb for added comfort. They look great!

Splendid colour. You have a lto more patience than me. Two minutes in and I would have ripped it to shreds in anger.

@AndyManCam

2 жыл бұрын

Haha! I felt like that at times too mate! The colour is really cool though!

@CalmBiker

2 жыл бұрын

@@AndyManCam It certainly looks it in the video.

That tank would of gotten the sledge hammer half way through if it was mine! LoL those wrinkles freaked me out!😂

I wrapped a Christmas present once, never again.

@88888888Rocket1

2 жыл бұрын

LMAO 🤣 😂 🤣

@AndyManCam

2 жыл бұрын

That's a whole different challenge! Too much tape makes it look overdone, not enough and it looks like yesterdays fish and chips!

Fair play mate it looks good, I tried wrapping a while back and gave up. Didn’t have the patience and through a hissy fit.

@AndyManCam

2 жыл бұрын

Patience is definitely the key! Mostly because for 90% of the time it looks like it couldn't possibly turn out good!

Andy well done mate, i think Likeable rider needs to dig deep into his pocket especially after your fisrt attempt keep up the good work

@AndyManCam

2 жыл бұрын

Thanks Glenn! I shall enjoy that beer very much! :D

I must say you did a very good job for your first attempt. I tought this was going to be a disaster. he who dares he who dares

@AndyManCam

2 жыл бұрын

Cheers Gijsbert! I must admit that my hopes were also relatively low!

I think Im just going to paint mine after watching that.... I would have dropped a match in it if it were mine.... 3rd degree burns worth it!!!

@AndyManCam

2 жыл бұрын

Haha! There were moments when i felt the same! It’s not for everyone, but at least it’s relatively cheap and reversible!

Andy, I was just sat here wondering what to do to freshen up my motorcycle & this video pops up. I was tempted to wrap my tank after your previous wrapping video.

@AndyManCam

2 жыл бұрын

It's well worth a crack mate. 30 quids worth of vinyl and a free afternoon is the most it can cost!

@EpicAdamMotovlogs

2 жыл бұрын

@@AndyManCam I'll give it a try

@AndyManCam

2 жыл бұрын

Good luck and be patient!

I remember you do like that by your bike before Kawasaki versys 👌👌

@AndyManCam

2 жыл бұрын

Good memory! That feels like a lifetime ago now!

Nicely done Andy, far more patience doing that than I'd have had... would def have gotten launched out a window if I'd been having a go! :D Be interesting to see how you get on with attempt no2 when you get the chance :-)

@AndyManCam

2 жыл бұрын

Cheers mate. It was borderline for a while there! I always find this process incredibly nerve wracking! But turned out ok. We’ll have to wait and see what happens with round 2!!

Thats not a bad job Andy, i think it would have been painful to watch the original footage, but the time lapse worked great. It looks a lot cleaner without the Honda logo on the tank. Your a brave man attempting this one, i would have given up within minutes i think :)

@AndyManCam

2 жыл бұрын

Thanks Phil 👍 Yeah the realtime experience was a bit arduous! Definitely way better without horrible plastic badges!

Admire your patience with jobs like this! Looks good too! I wondered, what’s the screen you have? Is it specific for your Honda?

@AndyManCam

2 жыл бұрын

Thanks Haydn! Patience gained through years of simply learning to hide my burning rage! 🤣 The screen is from SW-Motech. They sadly stopped selling it for the CB, but it’s available for many other bikes.

What a cracking job !!! I did my hubbies vespa panels.....they are hideous !!! I think you should be well pleased with that. I will redo his panels when ive earned more money for the swear tanker i filled 🤬

@AndyManCam

2 жыл бұрын

Haha! Thanks!

Keep it up!! Looks great, quick shifter time!! Haha only Honda mod worth the $$

@AndyManCam

2 жыл бұрын

Thanks John! I'm still not decided as to whether or not I want to put the quick shifter on. In any case, it wouldn't be the 800€ Honda unit! That's too many $$'s for my tastes! :D

holy wrap mate, i think it ill end as a vinyl ball here lol!

@AndyManCam

2 жыл бұрын

Haha! I know exactly what you mean! The pressure was really on when I realised I didn't have enough wrap for a second attempt!

i would faff this wrapping beond any good, good job

@AndyManCam

2 жыл бұрын

Trust me mate, I was close at several points! :D

I love it

@AndyManCam

2 жыл бұрын

Thanks very much egg!

Nice job. I think the colour and finish of the vinyl wrap possibly highlight the imperfections. If you do it again, try starting at the back of the tank and work forward so that you're starting at a narrow point and working your way out.

@AndyManCam

2 жыл бұрын

Sadly youre absolutely right. Someone of my skill level should probably stick to plain colors and abstract patterns!

Seriously well done I put two clear tank protectors on my vstrom first side shit second side perfect went back to first side and ripped it off and through it in the bin.whats that saying a man on a galloping horse at 30 mph wouldn't be able to tell the difference 😂

andy,you obviously really,réálly love your cb-r..😉👍.r.e.s.p.e.c.t.

@AndyManCam

2 жыл бұрын

Yeah, she’s alright! Cheers John!

Fairly sexy that my friend! you should be congratulated for even attempting that in one piece m8....Bravo AMC!! Wheels next?

@AndyManCam

2 жыл бұрын

Cheers bruvv! He who dares! The wheels would be definite tantrum fodder!!

@tdmtam

2 жыл бұрын

Vinyl wrap wheels !!! 🦆 that! It’s bad enough trying to get the pinstripes tape on neatly.

@AndyManCam

2 жыл бұрын

@@tdmtam haha! So true! I need something with less angles, not more! 😂

no kidding hats off to you Andy definitely not something would try lol

@AndyManCam

2 жыл бұрын

Thanks Leo! I just decided that i had nothing to lose to give it a crack!

Kudos dude I'd have been inventing new swear words by the end of that Well done mate

@AndyManCam

2 жыл бұрын

Haha! Believe me, I’m my head it was a non stop bleep reel! 🤣

The Doris next-door, got Moore stretch marks 😛

@AndyManCam

2 жыл бұрын

Haha! I couldn't possibly comment!

"Badges? We ain't got no badges. We don't need no badges. I don't have to show you any Honda badges."

@AndyManCam

2 жыл бұрын

Hell no! And the badges may well be less seen than the missing treasure!

That looks great! A couple of hic-ups I wouldn't have noticed had you not pointed them out. Go ahead and forgive yourself then take the bike out for a spin

@AndyManCam

2 жыл бұрын

Thanks Alejandro. Done and done! 🙌🏻

Lovely job matey! OK so what slider are you using, love that look?

@AndyManCam

2 жыл бұрын

Cheers Chops! It’s one of these mate: MOZA Slypod: amzn.to/3sV6dQ8 not cheap, but very good!

@LambChopRides

2 жыл бұрын

@@AndyManCam is yours the E version Andy? Just about to press the buy button! Costing me money again you swine! 😎👍

@AndyManCam

2 жыл бұрын

Mine is the E mate. I had the grown up version, but it was defective and then out of stock! The E version is a chunk heavier, but the function is exactly the same. You just don’t get the fancy carry case!

@LambChopRides

2 жыл бұрын

@@AndyManCam OK thanks Andy 👍

@AndyManCam

2 жыл бұрын

No worries! Happy sliding! It’s addictive once you start! 😉

Andy I think there's a lot of married fathers out there that agree with your sentiments... Can't do anything at all about the stretch marks, just going to have to see how long they can take it and what to do about it! 😏

@AndyManCam

2 жыл бұрын

Hahaha! Say no more! ;D

I can see you really need patience of a saint for a rapping job. And apparently the better the quality of the vinyl the better quality of the Finnish. I say well done ole son. Good job.👍👍👍 If I could offer any tips. It would be to try using a soft cloth and or sponge on some of the difficult surfaces. And wherever possible, Less is More??

@AndyManCam

Жыл бұрын

Absolutely Paul. The cheap stuff isn’t worth the plastic it’s made out of! Less is definitely more though. For me, that means less wrapping!! 😅

@pauleverest5750

Жыл бұрын

@@AndyManCam Andy I will say that your video has given me confidence to av a go.

@AndyManCam

Жыл бұрын

Glad to hear it. Hope it all goes/went well. 👍🏻

Really impressive job. I'm surprised it was possible with a single piece. I'm still working out how to get the tank off (undoing the the connections without dropping it). 😂

@AndyManCam

2 жыл бұрын

Thank you Craig! I was convinced it was possible, right up until the point i had it on the table! 😅 I reckon a tank removal video might be in order, but with better light and more time!

Looks a great job in fairness. The difference removing the honda badge made was unreal, looked so much better without it.. You have the patience of a saint , i'd have ended up in the pub swallowing truckloads of Guinness...LOL

@AndyManCam

2 жыл бұрын

Cheers Mick! I totally agree with the badges. Even if I hadn't wrapped it, the badges needed to go anyway! A poor effort on Hondas part there! The guniess option doesn't sound too bad either though! ;D

Nice job! Were you able to put the R&G knee grips back on?

@AndyManCam

Жыл бұрын

I actually didn’t bother until i finally removed the vinyl. But the replacement knee pads that i got from R&G suck just as well as the first set. I.e, they were off again within a week!

Ideally you should’ve pre stretched the vinyl and covered the top, then as you heat the sides it shrinks back and takes away a lot of that excess you were left with. You need to hit it afterwards to about 85-90 degrees to kill the memory so a heat gun and thermometer is essential. Good effort though

I'd a stomped on the whole fokkin thing 🤣🤣🤣 Big kudos to you Andy for keeping on going. Result not at all bad... better than the tank I'd 've left you with a size ten imprint in it out of pure frustration 🙃😁😉

@AndyManCam

2 жыл бұрын

I wanted to at about half way as well! Thanks mate and luckily no lasting temper damage to the paintwork! :D

Good job Andy, how long did it take just to do the wrapping part, not including the prepping or removing and refitting of parts ?

@AndyManCam

2 жыл бұрын

Thanks Patrick. I think probably about 2 hours.

For an amateur was not too bad, actually. But, tbh, I'm curious how the edges are holding since then. 1st, brushed look vinyls can be very challenging anyway, it must be tackled carefully to keep the lines nice and not distorted. 2nd, trying do wrap in one piece a bike tank is another big challenging job. 3rd practice is a good teacher 😉 If you want my advice, for a future wrap, - place the tank on a stand, so it gives you access to work easily on the bottom, - ask a friend for help, much easy to work in 2 (3 even better) - heat the vinyl with a proper heat gun, to 50° - pre-stretch the vinyl then place it on the top and try to mold it to the shape of the tank - while you are doing this, be careful not to over-stretch the vinyl !! - heat the vinyl on the recessed areas, so the memory of the film will shrink it back to the original state ( like this you won't have so much material to work with and trying to get rid of it) - try not to over heat and keep stretching the vinyl, to avoid stretch marks and glue lines - go with the vinyl under the tank so it gives you a inner peace that won't start to peel off with time. Voila!

@avry87

2 жыл бұрын

And another thing, when you are heating the material to stick it in a recessed area, don't stick it from the middle, as you will put too much tension in the vinyl. Instead work it in from the lowest tension point to the highest tension point. Hope it makes sense

@AndyManCam

2 жыл бұрын

Thanks. Good tips. I don’t think I’ll be doing it again in a hurry though! I did however watch on the official 3M tutorials that they recommended heating and then working from the middle of a recess outwards as this spreads the tension across the space, instead of causing it to ramp up the further you go.

@avry87

2 жыл бұрын

@@AndyManCam yes, you are right about the recessed area. I was almost falling asleep when I was writing the comment 🙃

@AndyManCam

2 жыл бұрын

Haha! Not often I’m right about things like this!! 😅

Andy, what was the finishing strip you placed on the edge when it was done? Regular desk tape?

@AndyManCam

Жыл бұрын

It was just a strip of the same stuff, cut to about 10mm thick.

Vinyl wrap... One those things that look incredibly easy on video yet nearly impossible for the average person.

@AndyManCam

2 жыл бұрын

So very true! I hate doing it, every time! But always think i can so it better than last time. Until i try again and it’s painfully difficult!!

Good effort, tbh i didn't fancy your chances with the tank shape but still looks pretty good.... if you squint :)

@AndyManCam

2 жыл бұрын

Thanks CB. I was surprised too! Agreed with the squinting!

Where do you get the wrap and what size, please and thank you

bought my firsts bike and i want to wrap it, i have 0 patience so I might lose my mind lmao I have a feeling this will def teach me patience

@AndyManCam

3 ай бұрын

I can totally agree. You learn patience, or you throw it all out the window!