Morimoto XB Headlights Detailed Install | 2020+ Superduty
Тәжірибелік нұсқаулар және стиль
This is the most detailed, in depth installation video of the morimoto XB quad beam led headlights on a 2020+ Ford super duty.
XB Headlights
www.amazon.com/dp/B09CLTN8WN?...
Automatic wire stripper
amzn.to/3LtEMH2
Heat Shrink Butt Connectors w/ Solder
amzn.to/3xEuHl1
Check Out my amazon store for some of my favorite tools, gadgets and snowplowing accessories!
www.amazon.com/shop/snowplowlife
Contact Me:
Contact.OldSoulMillennial@Gmail.com
(Disclaimer) As an Amazon Associate, I earn a small commission from anything purchased in the amazon link(s) posted in this description. I use these funds to purchase new gear and reinvest into the channel. Thank you!
Пікірлер: 40
REALLY a well done video and great installation! Glad I found this and look forward to seeing additional content from this channel. Thank you.
Great video. Love the detail
Good find on the brown wire. I’m installing XB hybrids in the next few days and there was no way I was going to make a hole in the fuse box or lid. I was planning to use an upfitter switch until I saw this video.
@OldSoulMillennial
Жыл бұрын
Brown wire has worked flawlessly for me. No issues
Nice one on that wire you surely help all of us 😅. I’m getting those headlights for sure. I got a fifth wheel and my halogens made me nervous 😂👍🏻
@OldSoulMillennial
8 ай бұрын
Nice 👍
Thank you for this video. I’m ordering my headlights right now if it wasn’t for you I would’ve never bought them. Thank you.
@OldSoulMillennial
Жыл бұрын
Now if only I could get Morimoto to sponsor me!
I can confirm that my 2022 6.2L has the PTO supply wires bundled with the Upfitter wiring as in your video.
@OldSoulMillennial
Жыл бұрын
Thank you for the confirmation. Im sure this will help someone out. Did you test for power when the truck ignition is on? By chance
@johndavidson9423
Жыл бұрын
@@OldSoulMillennial Yes- tested at 14 volts when ignition is on. Proceeded with light install last weekend. Worked well. Thanks again for a great video. Now - let's see the video for adding / integrating Morimoto fog lamps!
Without the stock Grey Connector Connected Does That Allow Fogs with Brights?
What type wire and did you solder?
I have these lights sitting in my shed for my 2020 and glad I watched this, I really didnt want to tap into my fuse box. Did you cut the fuse link off the wire they provided and then install your own fuse, I know you installed your own just wasnt sure if you cut theirs off
@OldSoulMillennial
7 ай бұрын
Sorry, I don't recall. I think I may have left it in. That brown (pto wire) definitely has its own fuse somewhere. Your call on what you wanna do. Can't go wrong either way imo
Well, I was debating returning these lights because of that BJB fuse bullshit. I'll check to see if the Upfitter wire bundle on my 22 has the PTO wire as a KO source.... if it does you just saved my ass a lot of stress and time! Thanks!
@OldSoulMillennial
Жыл бұрын
I was in the same boat, didn't want to cut the fuse box or install a half ass fuse tap. Brown pto wire is KEY
@CDeHeer97
7 ай бұрын
Saved them a return on this end as well! @@OldSoulMillennial
I just installed them on my 2022 F 250, but with amber DRL , they are great in low beam, but not very impressed when running high beam no much difference from low beam . How are yours on high beam ?
@OldSoulMillennial
Жыл бұрын
High beams have a very narrow throw. I can see strait ahead, but going around corners, leaves a lot to be desired. Low beams are 2 times brighter than the original halogen lights, but still could be a bit brighter.
How did you wire the ground for the headlights or was that done for the lighted emblem?
@OldSoulMillennial
Жыл бұрын
Ground is only needed for the emblem.
How are they doing, any issues since installing? Just ordered the Hybrids!
@OldSoulMillennial
Жыл бұрын
No Issues! No Regrets!
How’s the brown wire working for the DRLs? I just got these and I’m going to try going that same route
@OldSoulMillennial
Жыл бұрын
Perfect. Everything is working flawlessly.
@thatguy5915
Жыл бұрын
@@OldSoulMillennial that’s good to hear. I just hooked mine up like that a few days ago and it’s working great so far
@johndavidson9423
Жыл бұрын
@@OldSoulMillennial What size in-line wire did you use to hook up the brown wire? Thanks
@Dcj01
10 ай бұрын
@@johndavidson9423yea what he said lol
Need some strobes for the new truck
@OldSoulMillennial
Жыл бұрын
Definitely, if I every decide to add a plow.
I need help doing the install from upfitter box can you make another video explaining out you did the install
@jorgeramos1105
Жыл бұрын
Which wire did you use under the upfitter relay I have a 2022 F-250
@OldSoulMillennial
Жыл бұрын
Look at your up fitter wire harness under the hood. There is a label attached to the wires explaining which wire corresponds to which switch.
@jorgeramos1105
Жыл бұрын
What wire gauge did you use and did you add a 10 amp fuse for the headlight and another for the putco emblem
@OldSoulMillennial
Жыл бұрын
@@jorgeramos1105 I don't believe I added a fuse, as that brown pto wire is already fused. I don't recall what gauge I used. I would say that you should be safe with 12 gauge. Make sure you use pure copper stranded wire. Avoid Copper clad aluminum.
The plastic grill is a little heavy😅😅😅😅😅😅😅😅
$1750......uh no thanks