Monroe Air Shock Adapter to 1/4" NPT Thead
Автокөліктер мен көлік құралдары
Here is how I convert a Monroe Air Shock to 1/4" npt.
Adapter - amzn.to/3ksjZKB
*Disclaimer: This video description contains affiliate links. That means that I am awarded a small commission for purchases made through them, at no added cost for you.
Пікірлер: 48
The adapters that come with the Monroe shocks have an indent in the center where you can drill it out with a quarter inch drill bit and the line will fit directly through it and into the shock and you can use the factory plastic adapters :-)
I think this is what I need!
super helpful thanks
Does this help it lift better and quicker? Thanks for your time
Thank you .. I got it
Thanks bro
Big hugs
A few questions: 1) On the fittings on the side of the Monroe Air Shocks, is there a valve-pin, similar to a normal (Schrader) Tire Valve, that must be depressed to add or remove air from the shock? 2) Do these Aeroquip 2242-4-4S adapters have a part inside that keeps the valve-pin depressed? 3) Or, does the Monroe setup work differently? 4) Do other Air shocks have a normal (Schrader) fill valve that's the same size as a Tire Fill Valve that will work with a standard air hose "Tire Chuck" ?
@Fentertainment
4 жыл бұрын
I dont know about other air shocks but these monroe shocks do not have schrader valves built into the housing. It is just a direct inlet. You would need some pneumatic valves to be able to build pressure and release pressure.
I want to screw a schrader valve directly on to the shock without any additional lines to run. Is that possible?
@tooflyklu
Жыл бұрын
you ever figure this out?
So would you have the part numbers are the numbers off the shock it looks like what I need is that about 9 or 10 inch from eye to eye when it is deflated thanks for the video
@adrianauvera4752
4 жыл бұрын
monroe ma785
Ok, so I purchase fitting and Now what size line 1/4 ? and what do I Need to connect from The shock ? Another fitting..thanks for ur help
@MrTonycaruso1
5 жыл бұрын
you can use any air hose for an air compressor that has 1/4"male NPT on it or any 1/4" male npt fitting
do you have a video showing the speed difference with the adapters.
@tonyinfinity
3 жыл бұрын
It doesn't make the truck faster
Can those air shocks run without air ? Would they work like normal oil shocks it theres no air in them ? I have some but wish to lower my rear end ( kinda normal ride height)
@rayturp6742
Жыл бұрын
NO. They would be like driving on tires without air. No function.
@rotorway133
Жыл бұрын
@@rayturp6742 actually I have been riding them without air for like 2 years. They also have oil inside like normal shocks. Monroe told me it was all ok
Monroe uses small hard plastic lines for several reasons. The line is inexpensive, durable, it's immune to weather and age rot, it can be routed in tight places away from exhaust, and most important it doesn't allow air to migrate from one shock to the other in the balanced system fast enough to effect handling in long high-speed turns. Big airline is a failure.
@Fentertainment
Жыл бұрын
I’ve used this method many times without failure. I’m sure they had great intent to use the smaller line and the reason I’ve used larger airline in the past has nothing to do with how the shocks were intended to be used.
Is the 1/8 inch line to small to inflate the shocks under heavier loads?
@Fentertainment
4 жыл бұрын
No, bot really. The larger line juat loads it faster.
@ravenfritts6615
4 жыл бұрын
Thanks
Ordered those fittings for my monroe shocks. they thread right on perfectly. My question is with them being swivel like...what keeps them sealed lol. I can put my finger in one hole and blow through the other, air shoots right out between 2 sections. Stupid question I'm sure lol.
@TrizzyKtre
3 жыл бұрын
Did you end up installing?
what shock is this looking for a small one like this
@stevekeller6675
6 жыл бұрын
they are for the old Volkswagen beetle's. late 70's. Ma803 is the part number i believe
@Bacardibombillo
5 жыл бұрын
U mention late vw. Would that be on the rear. Will it hold all that weight of vw engine? Just asking
Why?
you mentioned finding a 90 degree fitting,I found it here it is the 90 degree fitting its~ Eaton Aeroquip 2047-8-8S
@fallenangel5753
5 жыл бұрын
it doesn't fit
@Mryiyo209.
2 жыл бұрын
Link is in the video description
What monroe are these? Part no. Please:3
@marvinjgerald6007
8 жыл бұрын
@evo emperor, it doesn't matter what particular Monroe air shock model. All the male threads are speced the same so that the Aeroquip 2242-4-4s will fit all Monroe air shocks. In fact Aeroquip 2242-4-4s will fit all Gabriel air shock threads too.
@stevekeller6675
6 жыл бұрын
Looks like an Ma803
$5 my butt clicked on your link $17.29 Amazon is freaking horrible
@Fentertainment
6 жыл бұрын
Thats what they were when I made this video back in May of 2015. TImes have changed.
@MrTonycaruso1
5 жыл бұрын
www.ebay.com/itm/6506-04-04-Hydraulic-Fitting-1-4-Female-JIC-Swivel-X-1-4-Female-NPT-Pipe/113623522877 this should work and its 5$
These fittings are garbage do not buy them. The swivvle points leak air badddd. Buy a 7/16-20 female to 1/4 male fitting no swivel point or you will regret it
@dwuanedalebaza9608
2 жыл бұрын
Where can we find this fitting?
@chucknorris8954
2 жыл бұрын
@@dwuanedalebaza9608 all of this stuff is on amazon