I can't thank you enough for this very well produced instructional video. It was concise and easy to follow. If you can do all that work with one hand you certainly are talented! After removing the cylinder head on my daughters 2001 Golf (Timing Belt failure) and disconnecting endless hoses and electrical connections I was happy to learn I do not have to put all those hoses back to stock. You did a fantastic job showing each and every detail! I had noticed when disassembling our VW that several of those hoses and lines were dry rotted and surly there were leaks! Surprising the car ran as well as it did! Cheers!

@SPOOLINUP

2 жыл бұрын

You are more than welcome man, im glad it has been helping you along your way. Did the timing belt snap? If so any damage to valves/camshaft etc? Some work is done with one hand but some done off camera, I do have a head mount and chest mount but never use them. Yesterday I was working on the car and was topping up the break fluid when I noticed more hoses looking cracked in that area. I appreciate your breakdown of why you like the video as well so thanks for the nice feedback and good luck with the rest if the job in hand 👍🏽

I couldn’t find a better explained video in KZread, I understood everything after watching this. Gonna play it as I venture into this. Thank you 🙏🏻

@SPOOLINUP

2 жыл бұрын

Hey, sorry for the late reply but thank you. How did the job go? I hope it was a success for you 🙏🏾

Brave soul doing this as a newbie and very well done. Thank you.

@SPOOLINUP

4 ай бұрын

I did that as a total newbie too, I just followed an online guide. How did it go for you? i was told after making this video not to block the EVAP so if you did then please unblock it.

I’ve needed a video like this forever. Few years ago I wanted to do all of this but every video up was different, confusing, and or not descriptive. You are a saint 🙏

@SPOOLINUP

2 жыл бұрын

I know, that is why I tried to make one the best I could. The only thing I need to point out to people is not to block the EVAP like I did because it needs to be open to atmosphere. I'm glad the video helped you though man thank you 🙏🏾

Nice one for putting all the deletes in one vid 👍 Clear concise instructions 👍 didn't ramble on like some people do 👍👍👍 good vid ✔ well done!!!

@SPOOLINUP

3 жыл бұрын

Thanks a lot for the positive feedback, I appreciate it. The video and job took ages but was worth it in the end. Thanks again mate im glad you enjoyed it👍🏽

Love the GTI keep the videos coming!

@SPOOLINUP

3 жыл бұрын

Thank you man I will try to keep them coming mate!

Top job mate and well explained. Hopefully get mine done next weekend once my missing T-piece arrives.

@SPOOLINUP

3 жыл бұрын

Thanks bro, means a lot! Just make sure you leave enough time to mess about with it all and make it good for yourself. I'm sure you will smash it! Let me know how it goes 👍🏽

Bro, invest in a better camera and keep it up! Your putting out some of the best & well detailed mk4 content on KZread!

@SPOOLINUP

3 жыл бұрын

Yo man thanks for the advice, will look into investing in a better camera or adjusting mine, ive been using it straight out of the box. Thanks man cheers for the feedback 👍🏽

@eliasparet4771

3 жыл бұрын

@@SPOOLINUP same here bro you definitely earned a sub here 🙌🏽

@SPOOLINUP

3 жыл бұрын

Thank you, I appreciate your support 🙌🏽

@Slai.

3 жыл бұрын

@@SPOOLINUP try and uping the shutter speed on it = the footage will be darker but will have less motion blur making it look better, and id you're recording with your phone look into apps that let you adjust your exposure, shutter speed etc while recording :)

@SPOOLINUP

3 жыл бұрын

Cheers mate I will look into the settings of my camera, thanks for the advice.

Absolutely amazing contence m8 possibly the best 1.8t deletions video tutorial.

@SPOOLINUP

3 ай бұрын

Thanks brother, just remember not to block off the EVAP, in the guide I followed and this video it tells you to but make sure you let it vent to atmosphere.

Best delete tutorial on KZread hands down 💯💯💯 every other video made it seem incredibly difficult, and made me not want to do it. I'm almost done with it now thanks to you!!

@SPOOLINUP

2 жыл бұрын

I was exactly the same, it was a job I put off for ages and dreaded it so much. I'm glad the video helped you and made it seem possible for you. I have been told since not to block the EVAP port in the engine bay so I've taken the little red vacuum cap off now. Thanks for the feedback man.

@thegooserider7245

2 жыл бұрын

Agreed

Really enjoy watching these videos keep it up man

@SPOOLINUP

2 жыл бұрын

Thank you, I apologise I never saw this comment.

This is just what I need, I also have a 1.8t AUM and am planning to do all these deletes. Great video bro

@SPOOLINUP

Жыл бұрын

Thanks man and good luck, its not a bad job. Just make sure you don't block off the EVAP and you leave it venting to atmosphere.

Another well thought out and detailed video!! 👍

@SPOOLINUP

2 жыл бұрын

Thank you mate, trying my best. Glad to have you watching again 👊🏾

Good video I might even try do my auq myself after watching this keep up the good work

@SPOOLINUP

3 жыл бұрын

Yo, thanks man go for it you will clear the engine bay up nicely. You can even just use the guide that is online it was really really helpful. Good luck and thank you man

Thank you for taking your time and effort putting this tutorial toghether , i found it to be very useful ,as i am in the proces of doin this job myself ,and was'nt to sure about wich hoses to route to the oil can ,and wich one's to cap off 😅....you showed me exactly what i needed to see ! Thanks mate 👍🏽

@SPOOLINUP

3 жыл бұрын

You are more than welcome man im glad it helped you, I literally followed the same guide you are probably using to get it done. Its not an easy job, requires patience and time as you know yourself! I read the guide over and over again before I even considered doing it. I'm glad you are getting it done mate good luck with the rest of it 👍🏽

@sepstersepster9297

3 жыл бұрын

@@SPOOLINUP yeah ,mate ...i'm feeling exactly the way you do ,about this job ,and viewed some sai delete vid's before i started ,and due to the large amount off hoses going everywhere ,it's sometime's a bit confusing ,and i don't wan't to remove or cut stuff ,that needs to stay in place 😅 .

@SPOOLINUP

3 жыл бұрын

Exactly mate, even when you think you are sure there is still a doubt that you could be wrong. I just took my time tracing things around the engine bay several times and taking a good look. Amount of rubbish that comes off is crazy. I viewed a few videos before but that guide was the best thing online with the photos.

RIGHT! I've literally this minute finished doing this on my AUM, used your video as a reference when I needed it. Very helpful & informative. You're a diamond pal, thank you!

@SPOOLINUP

2 жыл бұрын

I'm glad you went for it man and im happy to hear the video came in use here and there if you ever got stuck. Well done for getting it done as it isn't easy. Thanks mate!

@FiendX02

2 жыл бұрын

@@SPOOLINUP Runs sooo much smoother too, i was suprised, I bought the Cloud9 Catch Can in the end, came with everything needed, apart from an unfortunate slip with the stanley blade, all went smoothly haha!

@SPOOLINUP

2 жыл бұрын

Hahaha, so in that case then you could have had a small vacuum leak and removing these items got rid of it. What did you slip into with the Stanley blade? Lol

@FiendX02

2 жыл бұрын

@@SPOOLINUP my hand, left blood everywhere, but the cars done, that's what matters hahahaha

@SPOOLINUP

2 жыл бұрын

Ahh damn, your hand will heal, if you cut through the wrong hose it wouldn't heal 🤣🤣

Great video man, very well detailed.

@SPOOLINUP

2 жыл бұрын

Thank you man, much appreciated and glad you thought so.

Very clear and well delivered tutorial well done young fella 👍👍

@SPOOLINUP

Жыл бұрын

Thanks Ivan, means a lot mate 👍🏽. Just one thing to let you know in case you weren't aware I made a mistake in the video. The EVAP doesn't require blocking, that is supposed to vent to atmosphere.

@ivancookemrshadowban4347

Жыл бұрын

Yes I know about that I once had trouble with the evap on one of my TT. Keep up the vids I think you could have a future doing that kind of thing , 👍

@SPOOLINUP

Жыл бұрын

Nice one man, what car do you have now? Have you still got an Audi TT? Again thanks a lot for the kind message and support mate it means a lot, really appreciate it 👍🏽

Great vlog brother naz on the santa pod drag strip at the end 👍👍

@SPOOLINUP

3 жыл бұрын

Thank you Andrew bro, yeah that other MK4 at the end I think was a non turbo and my car is not even mapped but gave it some 👍🏽😆

@andrewgrimwood6280

3 жыл бұрын

Lol love it

Great video bro 🙏🏽

@SPOOLINUP

3 жыл бұрын

Thank you bro! It means a lot 👊🏾

Excellent video mate. I'm building a 20v engine at the moment and im definitely gonna remove all this nonsense before fitting it in the car. Keep it up mate. You got skills

@SPOOLINUP

7 ай бұрын

Sorry for the late reply man, good luck with the build and its a very good idea to remove this before fitting as it would be very easy. Thank you for your kind comment

this video just got you a new subscriber 🙏🏻

@SPOOLINUP

9 ай бұрын

Respect 👊🏾 thank you. I've been told not to block the EVAP since this video though so keep that venting to atmosphere 👍🏽

We need a POV in this golf!! Sounds meatyyy

@SPOOLINUP

3 жыл бұрын

Yes certainly will do that, just need to get the front mount on, sort a few niggles out and get it mapped.

love the bit were you kept looking in mirror and that silver golf was coming for you haha i knew you gave him a cheeky run for his money video hard skipped to a complete different bit loool epic

@SPOOLINUP

3 жыл бұрын

Hahaha you know that other MK4 was coming for some smoke 🤣🤣 good observation!! Shame the car isn't fast enough but its all fun and games man. Im glad you enjoyed the video bro thanks for your comment. Priceless 👍🏽👍🏽

Happy there was a towel in those holes for a second I was freaking out

@SPOOLINUP

5 ай бұрын

Hahaha, I do make mistakes and I am a total amateur, but I do try and at least think a little bit about what I'm doing. Although even that doesn't always work 🤣

Awesome video man! Want to do it myself now🤣🤭

@SPOOLINUP

3 жыл бұрын

Thank you man! By all means go for it, just take your time and you will be fine 🙂

Sick video mate!! Keep it up!! It’s so satisfying taking all that junk out!!

@SPOOLINUP

3 жыл бұрын

Thank you bro! Its so satisfying man, got ride of a vacuum leak or two 👍🏽

@mikehayes2560

3 жыл бұрын

That’s sick! I don’t know why VW over complicated their engines, makes no sense! Also keep an eye on that oil cooler elbow join, when I did the deletes, mine was barely held together, so I replaced it, and after all that cold weather we had, it broke again. Such brittle plastic! 👍🏻

@SPOOLINUP

3 жыл бұрын

Yeah I know, there is a lot of complicated systems to achieve whatever it is they wanted to do. I will definitely keep an eye on that oil cooler elbow, I was looking for the metal ones that someone was making but I couldn't find them, might have a search on Facebook. Cheers for the heads up 👍🏽

@mikehayes2560

3 жыл бұрын

Yes, exactly mate, the SAI pump is just plain ridiculous haha! Ooh I did search online for a silicone replacement, if they did one, but the metal one sounds a lot better. If you find it let me know as I’d 100% be interested!

@SPOOLINUP

3 жыл бұрын

Yes and the SAI pump weighs a ton too. Yeah man I will be keeping my eyes peeled for the engineered metal elbow because they looked pretty good to be fair, the OEM one lasted years though but I'm keeping an eye on it like you said.

Mate that was by fare the best video I have seen .There is so many shit one’s that I wish people didn’t bother but your video is spot on ❤️

@SPOOLINUP

2 жыл бұрын

Thanks man, I did try hard with this one and recordong it at the same time made it take ages to do. Hope it offered good guidance although it is not perfect. I've been told since not to block the EVAP in the engine bay but to let it vent to atmosphere so if you put a cap on it then take it off 👌🏾

@piotrprobala4808

2 жыл бұрын

@@SPOOLINUP sweet. Honestly,I did so many of them videos and most is so shit .Yours might not be perfect but you did say it’s learning Curve for you as well . I was thinking about EVAP,would it not be best to connect it back to intake hose so it will be burned?I don’t know ,it might be bad idea . Since you are venting to atmosphere,can you not smell the petrol fumes bud ?

@SPOOLINUP

2 жыл бұрын

Yeah I know because I was looking for a good one to follow myself, in the end the best thing I found was the online guide in the description. With the EVAP venting to atmosphere you can smell petrol sometimes when stationary or with the heater/air con in use but not all the time. I am not sure what the best alternative for this is and no matter what you do im sure someone out there will tell you whether it is worth doing or not.

Top video mate very helpfull

@SPOOLINUP

Жыл бұрын

No problem mate you are welcome. Don't forget to leave the EVAP vented to atmosphere, don't blank it off like I did.

Excellent video buddy weldone

@SPOOLINUP

2 жыл бұрын

Thank you mate, appreciate it 👍🏽

Nice video men, when i watch its looks so much work to do, one day i will need to do on my one at least 2 days job here as i see :) anyway good video and new sub here

@SPOOLINUP

2 жыл бұрын

Thank you man, yes to be honest there is a little bit of patience needed but after some swearing, cuts and bruises you will get there. Yes the most important thing is time and preparation. Thanks again man I appreciate the comment and sub

Just found your channel. Great content. 👍🏾 I've got an AUM too. Just an idea if you want some more turbo spool and DV noise, take off the under bonnet sound deadening. Did mine and made a big difference. Running a pro ram cone and Forge 007p

@SPOOLINUP

3 жыл бұрын

Thanks for coming to watch the videos man and leaving a nice comment. I've heard those pro ram cones are good. Is it a common thing for people to remove the sound deadening?

Finally someone’s done a video I can actually understand, what size was the Caps you used please mate and size pipe I need.

@SPOOLINUP

3 жыл бұрын

Hey man, all of the sizes of the pipes and hoses should be on the thread that is in the link in the description. As for the caps most if them I used were in an assorted selection bag from Amazon and I ordered some extra ones for the turbo inlet pipe but can't find the order as I checked out as a guest from that particular website. You need a largish cap or two for the TIP and for the bottom of the inlet manifold. Maybe 8mm or 10mm man sorry I am not 100% sure, I had to order them halfway through the job as I didn't have ones big enough. Good luck though with the job 👊🏾

@TheEddiejunior

3 жыл бұрын

@@SPOOLINUP nice one for that. Keep up the great videos. 👌🏻

Good tidy work 🙂

@SPOOLINUP

Жыл бұрын

Thank you my friend 👊🏾

Good video. I must admit that I usually only watch your fiesta videos as I have no interest in a mk4 golf or a BMW but the videos are interesting anyway.

@SPOOLINUP

3 жыл бұрын

Gary nice one for watching regardless man always appreciate your support. I've got the carburettor on the XR2 going off to be reconditioned tomorrow with a 4-5 week turn around. Will have an update on the Fiesta soon and once I'm over the hurdle of the running it will open new doors 👍🏽

@garysanderson1639

3 жыл бұрын

@@SPOOLINUP looking forward to it 👍

@SPOOLINUP

3 жыл бұрын

I won't disappointed you mate 👍🏽

Having some issues now with my idle hopefully this kit will solve everything cheers for making such a great in depth 👌🏽

@SPOOLINUP

Жыл бұрын

I hope it fixes your issues too my friend. Just remember to NOT block the EVAP which I block in the video. I was told by the guy who tuned my car that it shouldn't be blocked. Let me know if it all works out.

@strielokholmes4254

Жыл бұрын

@@SPOOLINUP do you talk about the EVAP somewhere? will follow ur vid in the near future and probably some others too, really well done vids I ve watched so far, keep it up mate!

@SPOOLINUP

Жыл бұрын

@strielokholmes4254 Yea the EVAP also gets deleted in the video. The guide that I used is in the description of the video and it says to block the old EVAP off with a vacuum cap. You are supposed to leave this venting to the atmosphere otherwise the vapours in the fuel tank can build up. I hope the guide helps you mate, good luck and thank you.

Hey dude, thanks for the video, not many around where someone does the whole engine bay simplification from start to finish. Nice one, I've subbed 😎. Have you seen any reduction in power or poor MPG over the last month since doing all these changes? Take it steady.

@SPOOLINUP

3 жыл бұрын

Hey man, nice one for coming along and subbing and im glad you appreciate the video. The reason I made the video is because there weren't many good ones and I needed to do it so just did it. I havent noticed much to be honest, only a catch can full of disgusting liquid but other than that I have seen no change in anything. I never really monitor fuel usage because my use of the car varies so much its difficult! Hope you get along well with doing the job man good luck to you 👍🏽

Decent video!

@SPOOLINUP

3 жыл бұрын

Thanks mate 👊🏾

First-off: Fantastic delete-tutorial brother! 2ndly: Anything EXTRA you would have done in hindsight? Followed the link and found the list to order everything! Cant believe they designed this motor with so much extra GARBAGE everywhere. This is gonna be FUN! Anyway...good work. #newsub

@SPOOLINUP

Ай бұрын

Thank you man, I appreciate your comment. Just make sure you do not block off the EVAP in the engine bay like I did and you should be all good. Just take your time and use it to learn a few things. I know there is a lot of garbage in a stock engine bay but it's all emission control. Thank god we can delete it!!!

Loving that bracket bro. I mounted mine on the plastic box where all the relays are housed but tbh i am not happy with it. Definitely needs to be mounted against the metal body of the car like you have done

@SPOOLINUP

2 жыл бұрын

That homemade bracket Hahaha. Listen man if you get a piece of metal with a 90° bend in it then just make some holes and away you go. I have seen some people mount it at the front as well near the bonnet catch.

@SPOOLINUP

2 жыл бұрын

Still need to spray that man you reminded me

@scott2495

2 жыл бұрын

Go over it with a scotch brite pad before you paint it so paint sticks to it better, maybe bang it oven at 130c for 15min just to bake n harden paint as well

@SPOOLINUP

2 жыл бұрын

Good shout man, I did attempt to rush spray it once and quickly wiped the paint off because it looked like I dunked it in a pot of paint and pulled it out 🤣

The piece you pulled off and shown at 10:35, i don’t have but is black and plastic (not much of a description, I know lol) I just bought the car back in august and I’m trying to learn more about what’s done to it since the previous owner doesn’t know the history on it. I found the pcv has been deleted, and same with the sai. Also just out of Curiosity what is clear hose for that T’s off of the fuel rail? One of the previous owners did that same thing and is hooked up to a boost gauge. By the way great video, its very detailed and helpful. You’ve earned a sub.

@jaminwing2758

2 жыл бұрын

Update: I’m still watching the video as I comment, the black piece I have is what you replaced

@SPOOLINUP

2 жыл бұрын

Sorry mate where do you live in the world? I was fast asleep 10 hours ago man so sorry for the late reply

@SPOOLINUP

2 жыл бұрын

That would be the Combi Valve that I pulled off there and then you block off where that would have gone with a blanking plate. The clear hose that I have coming from my fuel rail is also for a boost gauge so its probably a similar set up. I have now got my boost gauge running off the vacuum line that goes to the top of my diverter valve. I appreciate your sub and comment man! Thanks for the support. I hope everything is helpful for you

@jaminwing2758

2 жыл бұрын

@@SPOOLINUP yea we have a pretty similar set up, could I add you on snap so I could possibly show you what my set up looks like for a better understanding of what I’m saying? You’re welcome for the support, the video helped me understand my motor a lot more.

nice video mate but you need to vent the pipe coming from the fuel tank, to relieve excess pressure

@SPOOLINUP

3 жыл бұрын

Yes you are correct man thank you it is now venting out to atmosphere! I wish I could change it in the video but I can't. Thanks mate 👍🏽

Good stuff bro

@SPOOLINUP

2 жыл бұрын

Thanks mate 👍🏽

@NiiickTheGreek

2 жыл бұрын

Mines having all this done hopefully this week 💪

@SPOOLINUP

2 жыл бұрын

@@NiiickTheGreek I'm sure you will be very happy with the results man 👊🏾

where did you connect the wastgate hose that would go to the N75? In the video you cover it, but note that the N75 has the same amount of hose

37:51 i'm like "do it, come on do it I know you want to. Yank that hand brake and full lock the steering wheel" lol.

@SPOOLINUP

3 жыл бұрын

🤣🤣🤣 yo you know what? I think I'm resting my hand on the passenger seat to stop myself getting sent over to the other side of the car!! Maybe I will do a yobbo driving video soon

👍👍👍👍👍

@SPOOLINUP

3 жыл бұрын

👊🏾👊🏾👊🏾👊🏾👊🏾👊🏾

Love the videos man keep up the good work 👍 quick question, I done the evap delete on my GTI and when I open the fuel cap air seems to be locked into the tank and releases when I open, does that happen you? Cheers.

@SPOOLINUP

2 жыл бұрын

Hi mate, sorry. Dont block the EVAP in the engine bay, if you put a cap on it then remove it and let it vent to atmosphere. Basically it will allow the fuel vapour to build up, my mistake in the video I blank it off. Remove the cap and it will be fine. Thanks by the way! Appreciate your comment. I hope this resolves your issue

if you keep the coolant ball shut you can avoid all the spillage from the temp sensor hole

@SPOOLINUP

3 жыл бұрын

Yes it seems to only party prevent the spillage though

Perfect video man. I copped a cupra 1.8t few months back and ur videos help. Can u help me though? When i unscrew the oil cap at idle, it dances around. I replace pcv but there is still alot of blow by. Have u encountered this?? Cheers

@SPOOLINUP

3 жыл бұрын

Yo man thank you!! I'm sorry I have not encountered this at all and I am unsure of what is causing this problem for you. The best advice I can give you is to have a look on the forums or maybe on one of the 1.8t Facebook groups. I know excessive blow by can be a result of worn piston rings. Have you done a compression test?

Firstly, love your videos and fair play to you carrying out some of these jobs outside with a jack. I have the luxury of borrowing a mates ramp to work on my mk4 and don't stay as calm as you! :-) Just watched your vid on the CM oversized TIP as I'm doing mine next week at same time as new clutch. Watched this out of interest as I've already done deletes except for evap and pcv / catch can. Was wondering if you've changed your MAF housing to 80mm since doing the TIP install as I didn't see the adaptor in there?

@SPOOLINUP

3 жыл бұрын

Thanks a lot mate, appreciate your love for the videos. Working on the car on the floor is a total nightmare sometimes but I just take my time. I would love to have a ramp to use that would be heaven hahaha. I havent changed the MAF, I ended up changing the TIP because the other one kept sliding off my turbo but when I got this one it did the same thing. I still have the larger 80mm TIP so if I change the MAF I will use it. Good luck with your clutch and TIP upgrade man and thanks again for your comment 👍🏽

@Just_James_79

3 жыл бұрын

@@SPOOLINUP That's a shame about the TIP, have you figured out why they were sliding off? I'll be changing my MAF housing to 80mm but not until it is at the tuners for mapping or it will run lean.

@Just_James_79

3 жыл бұрын

Did mine today, absolute pig of a job! Clutch was much quicker and easier than TIP! It definitely needs some cutting off it (quite a bit) to fit on to turbo and gear linkage cables removing as well as the bracket for hard water pipe. Once it was on properly it took a mate with a pry bar to get the bracket for gear cables back in place while I got the bolts in. Seriously tight! Just wondering if you've not chopped it and got the gear cables out of the way it might be sitting at an angle and not 'square' to the turbo which is causing them to slip off?

@SPOOLINUP

3 жыл бұрын

Basically I cut the first TIP that I fitted and when I was going up the jubilee on the turbo spigot the jubilee kept slipping off. I thought it was doing this because I had cut too much and the jubilee was sitting on the tapered part of the TIP but I was wrong because a brand new uncut TIP did the same thing. I too tried to remove the gearbox cables and put them on after but was impossible by myself so just soaked it in hot water to soften the silicone and and some lube, was a hard one but nice to be done. Im glad to hear you got it on mate 👍🏽

@Just_James_79

3 жыл бұрын

@@SPOOLINUP Pal, I was doing the job with the luxury of a ramp, workshop full of tools and supervision / help from a very experienced mechanic..... and it was an absolute pain! Once again, much respect for you carrying out these jobs on your own outside with 'every day' tools!

That’s a fairly clean throttle body for an 21 yr old car

Same as everyone else great video , did you ever get any codes come up after a while after doing this ? And are you still running your car like this

@SPOOLINUP

2 жыл бұрын

Hey man, yes codes came up after doing these deletes but I cant remember off the top of my head what they were. I have had the software deletes done from my ECU so that the car no longer throws the faults up. The only thing I have changed is I took the vacuum cap off the EVAP in the engine bay and it now just vents to atmosphere to prevent a build up of fuel vapour in the tank. Thanks for your comment and keeping it positive and supportive.

Nice video! thank you! Im gunna do this with my Golf soon (AUM) where did you get your catch can Kit? & did it come with everything you need?

@SPOOLINUP

2 жыл бұрын

Apologies for the late reply. The catch can came by itself from Creation Motorsport, I had to make the bracket myself. If you look online for 19mm catch can kits you can find them on amazon for example. If you use the guide in the description as a shopping list you cant go wrong.

@FiendX02

2 жыл бұрын

@@SPOOLINUP legend, thanks!

@SPOOLINUP

2 жыл бұрын

Any time my friend 👊🏾

Hi mate, been watching you're vids, big help, appreciate that. Just ordering stuff for deletes... Do you think 1m of each diameter hose will be enough? and what size blanking caps did you use?

@harveydudbridge4920

2 жыл бұрын

Also why'd you replace the coolant neck?

@SPOOLINUP

2 жыл бұрын

Hi mate, im glad the videos have been helping you and thanks for watching! I apologise for the late reply. The hoses for the catch can need to be a little longer than a meter. If you look in the description there is a link to a guide which tells you pretty much all you need. As for the vacuum caps I bought an assorted package from ebay or amazon and then realised I needed some larger ones so ordered them but I am not 100% sure of the sizes mate im sorry. I can imagine some were 4mm, 6mm, 8mm and 10mm but not 100% sure as I have even replaces some since. The coolant neck was replaced along with the PCV 90° because it may as well be done while you are working in that area to keep it fresh and new as they may break in the future. Sorry I can't be of much more help .

did you have a pcv valve in the t piece if so what way was it pointing

@SPOOLINUP

2 ай бұрын

The PCV valve was removed as part of the deletes. Are you talking about before or after?

I also have 2002 aum 1.8t bought all the stuff to do deletes last year.but as mine completely original and they going up in value now(standard).havent done it.still in two minds.have the resistor plugs to fool ecu.but have heard aum will throw eml as looking for airflow from sec air inj unit.has yours thrown the eml up.?.

@SPOOLINUP

3 жыл бұрын

Hey man, yeah im sure these Golfs are going up in value and loads of them have been ruined. As long as you don't ruin your car it doesn't really matter too much in my opinion. Have a good think about what you want to do. EML is up on the Golf until it gets mapped.

After almost 2 years of doing these deletes there is a downside i have noticed. That is that with the catch can the crankcase has more pressure in it, causing the engine oil to sweep through the turbo seals to the exhaust, making it smoke on long idle, increasing oil consumption at the proccess. The stock pcv valve helps vacuum all this pressure by opening and letting the intake suck all this up. Its not a problem for me, i dont care if my car smokes after long idle, i do care that the crankcase fumes get filtered and sended clean to the turbo

@SPOOLINUP

7 ай бұрын

Since doing the deleted I haven't noticed any increase of smoking during idle. In theory if the catch can vents to atmosphere then as long as the crankcase is at a higher pressure than atmospheric it should be able to disperse the gasses. Do you have the outlet of your catch can going to atmosphere? I've re-routed mine to terminate under the car rather than the TIP.

@SakisTheDrifter

7 ай бұрын

@@SPOOLINUP The outlet of the catch can is on the TIP for me. It doesnt smoke immediately on idle. I have to let it idle for at least 1 minute, then the smoke starts and gets worse the more i let it idle. I believe in my situation the smoke problem is much more sensitive because i dont have anything attached on the exhaust. Its just a straight pipe with the only restriction being the turbine itself. The pipe is also 80mm in diameter. So the exhaust has really low pressure, while the crankcase on idle has more so that lets the oil flow from the high pressure to the low pressure. If you are having at least the catalytic converter and 1 muffler on your exhaust, it should be hard to make it smoke so soon

@SPOOLINUP

7 ай бұрын

@SakisTheDrifter I understand what you are saying, I don't have any boxes on the exhaust either, but you could maybe try and blank off the TIP where you have connected it to the catch can and let the catch can vent to atmosphere and see if it helps.

@SakisTheDrifter

6 ай бұрын

@@SPOOLINUP I connected the stock pcv system a week ago and the smoking effect is greatly reduced. It definately has to do something with crankcase pressure. Your suggestion passed throu my mind a while ago and i believe that indeed it would help a little, but i dont want to do it,because i want some oily air to get into the intake of the turbine and the top of the piston to lubricate them aswell. I ordered the catch can you have on your video, because yours have wider fittings while mine has smaller, witch made a restriction and helping the problem i have

@SPOOLINUP

6 ай бұрын

@SakisTheDrifter Oh I see, so then in that case you have proven there is a difference. That sounds like a good idea using larger diameter hoses and fitting along with a larger port catch can. You can try and route it to atmosphere. The oily air that you speak of for the top of the piston probably gets burnt pretty fast so might not actually help.

Doesn't deleting the evap reg system fail the MOT on emissions? Thanks

@SPOOLINUP

3 ай бұрын

I'm not too sure to be honest with you!

Hey man I just did this to my mk4 and I’m getting a P1137 System too rich Bank 1 code and my rpm’s are bouncing up and down do you have any ideas on how to fix this? Thanks

@SPOOLINUP

8 ай бұрын

First of all in the video I blocked off the EVAP so if you did then unblock it to allow the vapours to escape. I would recommend inspect your whole engine bay and make sure everything you blanked off is sealed properly.

Love your videos mate any recommendations of where to get this done around London ? I ain’t got the balls to do it myself 😂

@SPOOLINUP

2 жыл бұрын

Thank you mate, I appreciate your comment. I took me a while to muster up the courage to go for it myself man 🤣 I do know one or two people who could do that for you with the click of a finger as they know the 1.8T very well. What part of London are you in?

@onlyfools8777

2 жыл бұрын

@@SPOOLINUP North London mate I appreciate the reply 👍🏻

@SPOOLINUP

2 жыл бұрын

Yeah same here man. Do you have somewhere to message privately and I can pass you a contact or two?

@onlyfools8777

2 жыл бұрын

@@SPOOLINUP top man I’ve just messaged you in instagram

@SPOOLINUP

2 жыл бұрын

Sweet mate I will reply now

get 10mm spacers for the front and 20mm for the rear and you'll have amazing fitment !!!!!

@SPOOLINUP

3 жыл бұрын

Is this with the standard BBS Montreal wheels? I do have 3SDM wheels but I'm not leaving them on, the potholes out there are atrocious!! Thanks

@Just_James_79

3 жыл бұрын

@@SPOOLINUP With standard wheels and 205/55/16s I've just done 20mm spacers on the rear and 5mm on the front. I've gone 5mm on the front for now because they were free from a friend who removed from his VX220 and it meant I could still use my original bolts and lockers (anything over 5mm you need longer bolts), 20mm on rear makes a huge difference and helps fill the arches. Could have maybe gone 25mm on rear but coilovers not installed yet and although tread well within the arch, the trye wall bulges out guite a bit on 55 profile so played it safe for now to avoid any rubbing.

@SPOOLINUP

3 жыл бұрын

@@Just_James_79 I'm thinking of kind of doing a winter and summer wheels setup and will buy some other larger spacers for the standard wheels with some larger bolts. Nice wheel fitment can set a car off really well.

@Just_James_79

3 жыл бұрын

@@SPOOLINUP Yep, the fronts have never bothered me (as stock they actually sit 5mm per side wider than rear) but I absolutely hated how far in the rears sat in those arches! I got the Mtec 20mm spacers for rear from ebay for £40 including bolts (make sure you get radius bolts if using original alloys) and it's without doubt the best £40 you can spend on the car!

@SPOOLINUP

3 жыл бұрын

I remember I got my car tracked after changing the wishbones and when I crouched down at the front to see how the wheels looked they sat so far in. Spacers can make a big difference to a car man and they arent expensive as you have said so its well worth it.

What size vacuum blank off caps did you need? If you remember would appreciate it 👍🏻

@SPOOLINUP

10 ай бұрын

Honestly I can't remember. I bought an assorted pack and used some of them but I had to order some extra ones that I measured with a digital caliper. I want to say you need some 3mm/4mm/6mm to be on the safe side but I'm sure you need larger for the TIP blank offs, but I would be lying if I told you I know for sure.

@xpong3012

10 ай бұрын

@@SPOOLINUP no that great mate I just wanna get some so I at least have some then I can always order some other I need if so thanks a lot again

@SPOOLINUP

10 ай бұрын

Yes mate I had most of the bits I needed but miscalculated so had to order some more. I then had an air leak from the ports under the inlet manifold so ordered some smaller caps and it worked a treat.

Hey and thanks for this, nice job Have you got any problems when deleting Pcv and prv ? I mean from crankcase breather to catch can, then straight to TIP!! No vacuum problems? Hesitate idle ? Also oil cap when idling is it under vacuum?? Sorry to many questions , goob job

@hosamosman5154

3 жыл бұрын

my Pcv delete is catch can to atmospheric, and blocked TIP port . I think yours is better.

@SPOOLINUP

3 жыл бұрын

Well I think that yours probably looks neater to be honest as it gets rid of one of the hoses and its less risky because if I dont empty my catch can then its all going into my turbo.

@SPOOLINUP

3 жыл бұрын

There are definitely idle issues but I was told that it is due to the SAI delete, not too sure about anything being affected by the PCV delete. I have not been driving the car because I am aware that I need to have the deletes mapped out on a computer and then I'm sure any issues will go away.

Didn't really fancy the pain of doing this. I have the AUM in a new beetle. I don't know if it's the same? Where did you get your caps to blank things off? Excellent video though man 👌

@SPOOLINUP

2 жыл бұрын

It was painful but well worth it for sure mate. I just bought some assorted vacuum caps from Amazon and Ebay I believe. Its a long time since I did them and I even replaced one or two with better fitting ones since. I'm glad you liked the video though, sorry I can't help much more with where I got all of the bits.

@thegooserider7245

2 жыл бұрын

@@SPOOLINUP still a better answer than you get from some others. Really glad these engines are still being tuned. Thank you

@SPOOLINUP

2 жыл бұрын

Thanks mate, you arent the first to ask that question and I couldn't answer it then either haha. The good thing about the 1.8t is that it came in so many cars and these cars aren't the most expensive now, there are parts to buy new and used everywhere you look. 1.8t is a smart choice.

So I did the same installment but when I turn on my car it just dies and won't stay idling. Any help ??

@SPOOLINUP

Жыл бұрын

Hey man, I would suggest first of all checking all of the vacuum caps you have used and any new vacuum lines installed. Also check the blanking plate on the side of the engine to make sure that is all nice and tight. Just go back over your work and see if you can spot a problem. I had vacuum leaks under my inlet manifold because the caps I used were slightly too big. Dont block off the EVAP either, in the guide I used it says to block it but take the cap off that and let it vent to atmosphere.

Long shot as you might no be that active on here , but the break boost hose you replaced with 1/2inch , does it have to be a specific type of hose ?

@SPOOLINUP

Жыл бұрын

Hey, it should just be strong enough to not collapse under the vacuum. Best thing to just buy a silicone one.

@vinnystevens5044

Жыл бұрын

Appreciate the quick reply bro

@SPOOLINUP

Жыл бұрын

Any time man. I have used ASH (auto silicone hoses) they tend to be quite good. Creations motorsport have some good bits too.

Hi please, when you disconnect in 28:24 one hose from where are you disconnecting? I noticed that in my car the case which has the 3 hoses are loose..

@SPOOLINUP

Жыл бұрын

That hose is for the EVAP canister. Sorry I do not totally understand your question. You need to squeeze the button on the bottom of the connector on the hose and then pull it off. They will all seem loose and they will move but that is the type of connection they have there is nothing wrong with it.

@andreezequiel3186

Жыл бұрын

@@SPOOLINUP Yes that is the answer if seems loose and is like that is correct. This engine had massive amounts of hoses canisters and PCV VALVES... That will continue on my case . Many many thanks for your help and repays. Kind regards have nice weekend ✌️🏁

@SPOOLINUP

Жыл бұрын

Yes are you talking about the hard plastic lines? The shiny ones with the 90° connector that you have to press the button on to release? I have sent a link, if these are the ones that you are talking about then yes they always move up and down and will rotate as well. As long as they click in to place and can't be removed without pressing the tab then they are fine. You are welcome by the way. Blessings from England 🇬🇧

Dude what a video well done 👏 i think i have the sai delete on mh AUQ already but the catch can and vacuums under the manifold i want that stuff gone. so glad i have cane across this video..do you know what causes the engine management light from these delets? mine currently has no lights on dash just wondering if I'll come across this from the ones i want to do. again well done and thanks for the video 👍

@SPOOLINUP

3 жыл бұрын

Hey, thanks man im glad you enjoyed the video because it took some hard work getting it all done and filmed. Im sure that its deleting the SAI that causes the EML to come on and it needs to be coded/mapped to delete it. Was the SAI deleted or disconnected by someone before you bought it? There is so much junk in the engine bay before the deletes its good to get them done. Again you are welcome and im happy the video helped you.

@shaunwake9200

3 жыл бұрын

yes mate was already deleted when i bought it. iv been aware there are other deletes to do but never really found a vid that shows and explains the process. just want less in there so its easy to keep clean.. iv just swapped out the coolant pipes for silicone and done the aluminium connectors what a difference thats made. where did you get you 90 elbows from and the rest of the supplies at that?

@SPOOLINUP

3 жыл бұрын

Sweet man, thats good that has been done already and mapped out then you are ahead of the game. I need to swap out some coolant bits to be honest but will look into that in the future. I wish I did the deletes first because it frees up so much room to do other mods. The 90° elbows just found them on a Google search and the same with the vacuum caps, if you know what sizes you need it helps, all of the sizes should be on the guide in the description.

@shaunwake9200

3 жыл бұрын

mate what catch can you use?

@SPOOLINUP

3 жыл бұрын

Hi mate, I used Creations Motorsports catch can. If you struggle to find I will have a look for a link.

Nice job. Do you have a knock sensor unplugged? The VVT is for emissions or better performance?

@SPOOLINUP

2 жыл бұрын

Hey man, the knock sensor is still plugged in I havent touched it. VVT is there for emissions I believe it helps with emissions on cold start etc but no real performance gains unfortunately.

Hello good video! I have seen these kits that companies are selling they include the resistors where do i put the resistors?

@SPOOLINUP

2 жыл бұрын

Hey man, are you talking about UROTUNING and the likes? If you follow the link below it shows you where to put the resistors. I never used them as I just got the software deleted. www.vwvortex.com/threads/diy-ultimate-sai-n249-pcv-evap-delete.4893472/

@AMM-md2jr

2 жыл бұрын

@@SPOOLINUP yes thanks! How big are all the hoses in mm? And how long are they?

@SPOOLINUP

2 жыл бұрын

I cant remember exactly mate but even the link has it all at the beginning exactly what you need. I know the catch can hoses are 19mm. Any vacuum hose required is 4mm and I believe the hose for the brake booster upgrade works out yo be around 13mm but if you check the link its all at the beginning and you can use Google to convert it to metric as its all in inches and feet.

I am probably going to sound stupid but what is the evap delete and catch can install good for ?

@SPOOLINUP

2 жыл бұрын

No you don't sound stupid, before I bought this car I didnt even know what both of those things were good for. The catch can collects a load of vapour and oil that would otherwise go into the intake of the car and get burnt. Its not a lot at all but over weeks it collects in the catch can. There is no performance gain from deleting the EVAP but its connected to some of the other parts you deleted from the engine bay, clears up some clutter and is one less thing to go wrong. Hope this helps

the 90 degree elbow of the pcv system that you took off at 21:04, does this simply pull off once the U shaped locking spring thingy is removed? I'm having a hard time removing it :(

@SPOOLINUP

2 жыл бұрын

Yes brother that just has an O-ring holding it in place, give it a wiggle back and fourth while you pull it and see if it comes free. Do you have a spare one in case you break it because it may be brittle?

@Djiel

2 жыл бұрын

@@SPOOLINUP Thanks for confirming, I'll retry tomorrow. I do have a new one (it's the reason I want to take off the old one, preventive measure). Doing some work on the inlet manifold and surrounding bits.

@SPOOLINUP

2 жыл бұрын

Fair play mate good luck with it tomorrow then I hope it comes off nice and easily. I cant even remember if I bought a new one, I think I did. Let me know how it goes anyway mate.

@Djiel

2 жыл бұрын

@@SPOOLINUP You were correct, a good wiggle and it came off. The piece is absolutely gunked up.. yuck. Small piece of it broke off in the connecting T piece, otherwise it came out fine. The hose connected to the pcv valve had 3 massive holes in it.. glad I'm replacing the whole thing. The piece that broke for you, is made out of metal on the APP engine (slight difference in design), so I can clean that up and re-use it. Not sure why they went with plastic on the later engines, cheap bastards 😂

@SPOOLINUP

2 жыл бұрын

There you go man im glad you did it, some of these things just need a little persuasion. All of my PCV bits were gunked up and nasty too mate, I didnt find any holes but good thing you found the ones that you had there. I have never understood why they went with plastic bits in certain places, maybe manufacturing costs or something 🤣

What did you delete? Can you explain the cons of deleting all that stuff ? And do I loose my AC ?

@SPOOLINUP

2 жыл бұрын

Hi, the systems that were deleted basically mostly are there to control vehicle emissions. The cons of deleting them is that you end up with a tidier engine bay and you future proof your engine ridding it of potential vacuum leaks. Your AC stays!!

Hey bro, are you running Any issues after This delete? i want to know so i can prepare myself for it. (If there are any)... awesome Chanel love your vids!

@SPOOLINUP

3 жыл бұрын

Hey man, yeah there are some issues after doing the deletes to be honest. The EML came on as expected and the car has idling problems. The car doesn't always idle well, sometimes it bounces a bit but it doesn't happen all the time. Also I have noticed that the car doesn't have problems when it is left to warm up at idle for 5 minutes or so, when you drive it when its cold it has problems. Under acceleration its fine. I was assured after doing these deletes that the issues could be resolved with a map to delete the systems the ECU is searching for that are no longer in the engine bay. I hope this helps you somehow. I will be having my car mapped soon for the deletes as I dont drive it as my main car so I havent been using it. I hope this helps you and I appreciate your feedback. Best of luck man 👍🏽

@daanswagemakers9022

3 жыл бұрын

@@SPOOLINUP maybe i will only do the n249 and the SAI. Thanks for the fb 👍🏻💪🏻

@SPOOLINUP

3 жыл бұрын

To be honest with you I am not sure what causes the biggest problems in terms of how the car runs if you haven't had it mapped to run with the deletes done. SAI is a good one, you get a good sense of achievement after that and the engine bay looks a lot better.

Gotta ask... Where abouts is the evap bit that you shouldn't have plugged/capped off? Also... What's happening with your wheels?

@SPOOLINUP

Жыл бұрын

It's the part in the top left corner of the engine bay right by the coolant bottle. The wheels will be going on when the tyres on my current wheels get bad which will be in the next month or two. I just need to sort out a better tyre size for them because they are too stretched and too small.

@jruskin7174

Жыл бұрын

Looking forward to seeing them. Thanks for the reply. I'm just about to tackle all this. Also... Have you got rid of the smell in the car? I've got the same and really really hoping it's not the heater core breaking down: that's a long job.

@SPOOLINUP

Жыл бұрын

Yea mate I am looking forward to seeing them on too. I even got two refurbished as they weren't as good as I wanted them. The smell in my car has gone now mate. Is the water in your car oily kind of and slippery? Like is it definitely anti-freeze? I left my dehumidifier in the car too but after a hot summer it was fine. Good luck with the job

Anyone got links for all the nessesery stuff?

@SPOOLINUP

2 жыл бұрын

No but you can look at the link in the description and Google search the individual items. There is a company on ebay that sell a kit with the elbows and tee pieces along with some hoses etc for the catch can install.

Do you pass emissions test anymore?

@SPOOLINUP

27 күн бұрын

I wouldn't pass it because of my exhaust anyway, so I'm not sure after the engine bay deletes. I've never tried.

Where did you buy all the parts?

@SPOOLINUP

3 жыл бұрын

Ebay, Amazon and various websites from using Google search.

Hey did the resistor remove the secondary air engine codes. Or do I need to map it on order to delete that code?

@SPOOLINUP

2 жыл бұрын

Hey, I never fitted any resistors I just got everything mapped out and cable tied the plugs out of the way.

@trojangpete8

2 жыл бұрын

@@SPOOLINUP wow, why didn’t that cross my mind. Thanks 🙏

@SPOOLINUP

2 жыл бұрын

No worries man, literally anything that would be flagged up after the deletes was mapped out and my second lambda was mapped out too. Hardware deleted from engine bay and then software deleted from ECU.

Absolutely no idea once again but hello 😍🤤😋🤭😂

@SPOOLINUP

3 жыл бұрын

Thanks for coming to watch anyway. Got the KZread hat on 🤣🤣

@user-ej9yb4yc2l

3 жыл бұрын

better than the dead trim 🤭

@SPOOLINUP

3 жыл бұрын

Hahaha there is no 'trim' and that is the problem 🤭

@user-ej9yb4yc2l

3 жыл бұрын

you’re lucky I don’t mind 😇😂🤣

@jakeharling9971

3 жыл бұрын

Yes yes Naz

Hey bro I see it said n249 delete also but I still see it there? Does it get deleted

@SPOOLINUP

2 жыл бұрын

Hey man, the N249 gets removed when you cut the hoses and take off the metal plate by the dip stick. The N249 is mounted below that plate.

Hi, did the consume increase? I have the same car and now it consumes 2l/100 more

@SPOOLINUP

2 жыл бұрын

Are you talking about fuel consumption?

@dekkers8

2 жыл бұрын

Yes I am, my mk4 spend more fuel than before, anyway I'm changing maf and oxygen sensor to see if that's the problem

Any links to the kit ?

@SPOOLINUP

3 жыл бұрын

Hey man, I made that kit myself. You can find all of the bits online. Use the link in the description of the video which takes you to a guide on a MK4 forum and its all listed there. I used Ebay, Amazon and Google to find the bits.

您好，关于删除这些，将出现 P0411 代码。我该如何解决？我真的需要你的帮助，期待你的回复。

Link to parts ? I’m having troubles 🤦‍♂️

@SPOOLINUP

Жыл бұрын

If you click on the guide in the description there is a list of bits that you need. You can Google each but and it should come up, if you still struggle let me know as I did this a while back but might be able to find some links

How's that working out for yuh today?

@SPOOLINUP

Жыл бұрын

The car is still going strong.

Ezz bro, I'm about to do all these deletes, what's your view on passing the MOT??

@SPOOLINUP

3 жыл бұрын

To be honest mate the Golf already has a decat. There are ways around it, if you ask around you will find someone who might be able to help you. Not sure how much the deletes effect the emissions. Remember there are 1000s of cars on the road that are modded and decatted making them unroadworthy if you get what I mean

@ricardopiscina

3 жыл бұрын

@@SPOOLINUP yes bro that's what I thought, all these modded cars with straight through exhaust systems must be getting around the mot somehows!! I building up a MK4 golf from scratch!! It was a wreck to be honest I've spent the last year hunting down all the interior plastics OEM its cost a fortune I also changed all of the cream headliner and pillars into black suede, lool now I'm hitting the engine, I've changed every single hose into silicone ones changed injectors into the bam ones, upgraded all the coolant flanges to aluminium changed every sensor I've put a direnza over sized radiator and now I'm going to do the deletes but im not going to use the blanking plate instead I've got bam head that I had fully restored and I'm going to be putting that on!! The bam head doesn't have the hole for the combi valve cut into it, my only doubt is this MOT pass loool

@ricardopiscina

3 жыл бұрын

@@SPOOLINUP love the show by the way, I remember when the xr2 came out we loved em!! Yes I'm that old lool

@SPOOLINUP

3 жыл бұрын

Damn man that sounds like quite a sweet project you have there man im intrigued. I respect the graft you have been putting in man projects arent easy for sure. Thats going to be a sick car! The fact is that if you have a nice car like that where you have obviously put money and time into it and then in my eyes its more likely to be passed even if it should fail. The modified cars that fail are probably the pieces of scrap that haven't been looked after or the ones that look like they don't belong on the road. I drove past a local garage and asked mate its all you can do! Good luck with that car though man it sounds like its going to be a unique one for sure!! Rate the hard work!!

@ricardopiscina

3 жыл бұрын

@@SPOOLINUP thanks bro it's been a journey lool I'm loving it tho, I'm no mechanic but I'm doing everything myself by reading loads and watching videos, I had to follow your tutorial about the condensation I was getting it bad and couldn't for the life of me figure out what was happening untill I came across your vid!! You explained it perfectly bro and now I have that problem solved!!! Nice one man!!

What are the benefits from Doing all the deletes can someone explain please 2001 1.8t mk4 gti look g for any advice on this

@SPOOLINUP

2 жыл бұрын

Removing vacuum hoses from the engine bay will lessen the likelihood of future vacuum leaks as these 1.8t engines suffer from them. It also de-clutters the engine bay massively, the combi valve, vacuum hoses, SAI etc take up a lot of room. So you are future-proofing your engine. By removing parts and hoses that could fail you are making it more reliable. I realised when I did the deletes that it freed up a lot of room in areas that would have helped me when I was doing my TIP and other mods so I would have done the deletes first if I knew this. Vacuum leaks can be hard to find, once the deletes are done you can the software deleted from the ECU so you get no engine management light and then its like they were never there. Read the thread in the description and Google it because im sure there are more benefits too.

@WalesPrideCymru

2 жыл бұрын

@@SPOOLINUP thank you for responding - did you personally notice a difference in throttle response or any noticeable changes?

@SPOOLINUP

2 жыл бұрын

You are welcome. To be honest I cant remember, I was mostly impressed with the extra space it made in the engine bay. I looked at the massive pile of unnecessary clutter on the floor after and was pleased.

Hi there , What engine code is this? I have skoda octavia mk1 from 2001 with 1.8T code AUM , it looks the same. I want to know if i can copy step by step from this video

@SPOOLINUP

3 жыл бұрын

Hi, the best thing to do is read the guide that is in the description first because that pretty much explains it for all engines. I know there are some small differences.

@SPOOLINUP

3 жыл бұрын

My car is an AUM

@georgeprincex

3 жыл бұрын

@@SPOOLINUP great, then we have the same engine. I will follow this for step by step proccess . Thanks

@SPOOLINUP

3 жыл бұрын

You are welcome man, reference the guide as well because its really good and that is what I used to make the video. Good luck

I’m 17 and mk4 gti or r32 is my dream car would you recommend it?

@SPOOLINUP

3 жыл бұрын

Yes I recommend it for sure and its a great dream to have something to work towards. Make sure you work hard and you can get whatever car you want. Good luck 👍🏽

@hotslide9152

3 жыл бұрын

@@SPOOLINUP thanks for the motivation, much appreciated

@SPOOLINUP

3 жыл бұрын

Any time man! You are welcome 👍🏽

@Zxkyyy

3 жыл бұрын

work hard bro. i just bought my mk4 gti 2 weeks ago. loved that car since a kid. 23 now. Insurance is the main reason for the wait.

@hotslide9152

3 жыл бұрын

@@Zxkyyy i know insurance is a pain, I just finished my first 1.3k insurance on my current car, I’m a full time worker at 17 which most teens aren’t, it’s a lot of hustle but it means I can get my dreams faster such as this car and I’m prepared to spent some coin on it😁

I am midway busy with this then all of a sudden i cant access the thread file, does anyone still have the thread document with the step by step, I am missing something here.🤣

@SPOOLINUP

7 ай бұрын

Good luck with the job but just don't block the EVAP off like I did, you need to let it vent to atmosphere. www.vwvortex.com/threads/diy-ultimate-sai-n249-pcv-evap-delete.4893472/

@donay-robingroenewald3210

7 ай бұрын

Did not expect a response, but thanks, man, your video helped me a lot. I just finished the project up yesterday. I will definitely have a look at that EVAP section. I blocked it off already.

@SPOOLINUP

7 ай бұрын

@donay-robingroenewald3210 I apologise as I don't always get notifications for comments. Unblock the EVAP because it's better to let it vent, this will allow the vapours to escape rather than build up in pressure. Just take the blanking cap off if you fitted it to the canister.

Had everything including cocaine

@SPOOLINUP

11 ай бұрын

Hahahaha extra well equipped then

Dont play with the evp your going to be sucking so much fuel its not funny. The deletes dont gain any power just makes it looks tidy under the hood. The catch can is the only gain in doing any of it

@Just_James_79

3 жыл бұрын

Deleting the N249 can improve performance with a remap. Why would deleting the evap affect fuel consumption?

@kurtlazarus1702

3 жыл бұрын

It dont do nothing in hp even with a tune. I tune cars for a living. The only time you see big power diffrence is when you stroke the motor. Bigger turbo ect you can chuck a shit load of money at the stock 1.8t but your limited you can get a bit more out of a agu motor but not much. Stock ko3 15 pis boost is max with a tune but it still runs out of puff in high rev range. Putting pod filters and pulling pcv vaules and evap out will not do nothing. Pull it all out get a good computer plug it in and look at your fuel trims. The ecm are slow as shit in 1.8t vws and cant adjust values quick anoth ether 1 minite its running lean the next rich tps starts to hunts back and forth. Then starts throwing throttle body vaule and tps codes the list goes on. Stroke it big turbo better engine mounts and mod the pasanger side engine mounting points on the engine block as its prone for snapping with high hp big turbo custom tune injectors fuel pump ect and standard copper spark plugs heat range 7 ngk platnum blow out at hi boost.

@SPOOLINUP

3 жыл бұрын

To be honest with you mate im not looking to spend loads of money on this car with stroker kits, forging, turbos, LSDs, wheels, tyres, suspension etc. Next thing you know you have spent all of your life savings on a car that is worth not much more than when you started. Its just a bit of fun for me along with many other people and the reason why we choose the 1.8t is because its cheap to mod. Thanks for all your info mate 👍🏽

@Just_James_79

3 жыл бұрын

@@kurtlazarus1702 Deleting the N249 doesn't increase hp but can help with performance as it has control over the diverter valve, the delete is recommended for stage 2 map. The deletes are worth doing to minimise chance of getting vacuum leaks which are very common on these old engines. You can get an AUM with the K03s to stage 2 for little money and they will make around 230hp. That's an 80hp increase from stock for some fairly simple mods and enough for me on a 19 year old FWD hatchback. Why do you think deleting the evap would effect fuel consumption?

@SPOOLINUP

3 жыл бұрын

The reason I did mine was to futureproof the engine from the common vacuum leaks, to de-clutter the engine bay and of course ive heard it is a good move to make when tuning a 1.8t. I always wanted a cool turbo charged car that I can have fun with that doesn't cost an arm and a leg. To many people I am sure the 1.8t cars have offered thrills for little or no money. Well said @Not Applicable