Replacing timing chain with a split link type, replace starter motor, engine oil and filter change and a steering idler arm.
Жүктеу.....
Пікірлер: 10
@vikingdrummer9140Ай бұрын
top job got the same pajero . for light surface rust i use aquasteel with my spray gun no need for nasty underseal
@StevenRobertTaylor
Ай бұрын
Hi, thanks, I actually have it back on lift now doing afew other areas. That aquasteel sounds good il give it a look. Do you just spray it on with a paint sprayer for compressor? Thanks for watching!
@vikingdrummer9140
Ай бұрын
@@StevenRobertTaylor yes with compressor i use 2lts a bit over the top lol but just redone it after 4 years was when i did it last time not cheep but works realy well thanks for the vids bruv
@StevenRobertTaylor
Ай бұрын
@@vikingdrummer9140 I'm not in a panic to get this done so I think I will take your advise and lash some of that stuff on before I coat with gravitex. It's bound to be better than doing nothing at all.
@vikingdrummer9140
Ай бұрын
@@StevenRobertTaylor mate i never underseal that stuff no need to and over 24 hours gives a lovely black finish to it sorry if ever my spelling is bad am crap at it am old school had 40 years on spanners just do family cars now but you realy are very good at what your doing all the best mate
@StevenRobertTaylor
Ай бұрын
@@vikingdrummer9140 Thanks! That's good to know about the aquasteel. I have the gravitex there sitting ready anyway. It will need something to blend all the patches in properly.
@kevinstuarttrainor392717 күн бұрын
Where did you find the Jaos?
@StevenRobertTaylor
17 күн бұрын
@@kevinstuarttrainor3927 actually found it on marketplace fairly locally. But never seen one again, fairly rare here
Пікірлер: 10
top job got the same pajero . for light surface rust i use aquasteel with my spray gun no need for nasty underseal
@StevenRobertTaylor
Ай бұрын
Hi, thanks, I actually have it back on lift now doing afew other areas. That aquasteel sounds good il give it a look. Do you just spray it on with a paint sprayer for compressor? Thanks for watching!
@vikingdrummer9140
Ай бұрын
@@StevenRobertTaylor yes with compressor i use 2lts a bit over the top lol but just redone it after 4 years was when i did it last time not cheep but works realy well thanks for the vids bruv
@StevenRobertTaylor
Ай бұрын
@@vikingdrummer9140 I'm not in a panic to get this done so I think I will take your advise and lash some of that stuff on before I coat with gravitex. It's bound to be better than doing nothing at all.
@vikingdrummer9140
Ай бұрын
@@StevenRobertTaylor mate i never underseal that stuff no need to and over 24 hours gives a lovely black finish to it sorry if ever my spelling is bad am crap at it am old school had 40 years on spanners just do family cars now but you realy are very good at what your doing all the best mate
@StevenRobertTaylor
Ай бұрын
@@vikingdrummer9140 Thanks! That's good to know about the aquasteel. I have the gravitex there sitting ready anyway. It will need something to blend all the patches in properly.
Where did you find the Jaos?
@StevenRobertTaylor
17 күн бұрын
@@kevinstuarttrainor3927 actually found it on marketplace fairly locally. But never seen one again, fairly rare here