minn kota power drive with I-pilot AND foot control
this is how I can run a foot control and I-pilot on power drives with i-pilots.
Жүктеу.....
Пікірлер: 56
@Igotyerwheels Жыл бұрын
I just ordered my i-pilot upgrade and got it today, started installing it and I hit this dead-end realization. My brain starting turning (before watching this video) and this is exactly what I came up with in MY mind... I have to work early in the morning and the trolling motor is still laying in the livingroom lol the wife hates it but she's gonna have to deal with it for a day 😅 Good video! 👍
@omieyouknowme
Жыл бұрын
I was about to break out the fluke and make a y cable, but this was so much easier.
@dfsiv15 ай бұрын
Thanks man! You solved my problem!
@paulbowman3845 Жыл бұрын
Thank you. Now i need to find me a electrician to hook this up.
@omieyouknowme
Жыл бұрын
Watch the follow up video. I have paper diagram even a caveman can follow
@paulbowman3845
Жыл бұрын
LOL. Im no electrician for sure.
@bradleyreaux3 ай бұрын
What color are the wires that are coming out of the board for connecting the foot pedal? Read through some of the other comments -I do not have a black and white wire coming from board. I just have Green, Yellow, Brown and Ref. I have a 24v Powerdrive and am trying to do this set up but can’t figure out where my bottom set of wires are supposed to connect for the using the foot pedal.
@omieyouknowme
3 ай бұрын
The wires that come from the steering motor. They are usually black and white for all the motors I have worked on. It may be going to the main board instead of power head.
@rayhilley32214 ай бұрын
By adding the switch, does this allow you to use both remote and foot pedal without having to swap out the plug each time?
@omieyouknowme
4 ай бұрын
No you still have switch plugs. The switch is there so you don't have to remove cover to swap steering wires inside.
@patrickgarstecki9055 Жыл бұрын
Did you draw up a diagram as you said in other comments? I understand the switch locations for the white and black from the steering motor to the ipilot but I cannot tell what you are connecting on the other side of the switch for the actual foot pedal side of switch. I’m trying to complete this weekend so if you do have a diagram drawn could you please post or send to me. Thank you!
@omieyouknowme
Жыл бұрын
Will get diagram drawn up and uploaded by end of day.
@patrickgarstecki9055
Жыл бұрын
Thank you
@GaryJurceka Жыл бұрын
I wired up my DPDT switch with motor wires as my line side of switch and I-pilot wire and foot wire to load side of the switch. Both i-pilot and foot control work but it does not matter how the switch is positioned. They both work in any switch position. Am i missing something.?
@omieyouknowme
Жыл бұрын
The middle terminal of switch go to the steering motor, then one side of switch goes to the wires coming from board the other side of switch go to the I-pilot wires.
@robertsbroks Жыл бұрын
Hi, just bought footpedal no pdV2 with bluetooth, can you run footpedal with ipilot in parallel? I think the switch have not much use if you need to plug ipilot or footpedal anyway…
@omieyouknowme
Жыл бұрын
You can run one or the other not in parallel Have to change out the round plug for I-pilot or foot pedal.
@mulewrangler1 Жыл бұрын
I see the black and white coming from the ipilot to steering motor. But we cannot tell the color of the other two wires coming from the board that will wire to the other side of the DPDT switch. Can you clarify the colors, please,
@omieyouknowme
Жыл бұрын
It should be black and white from the board as well. Match the black to black and white to white on the switch. Ignore my green yellow just wires I had laying around.
@mulewrangler1
Жыл бұрын
@omieyouknowme thanks. I think we must have a later model board bcx we don't have a black and white coming from the board.
@caydenhomolka2408 Жыл бұрын
Anyone done this with the newer control board with the green,yellow,brown and red wires? I got the switch in but can’t figure out how to configure those into the foot steering portion. Thanks for any help!
@josephschweikhardt
5 ай бұрын
Every figure this out? I’m running into same situation I have red and green plugged in and can get the motor to turn right but can’t get it to go left. Any tips would help
@caydenhomolka2408
5 ай бұрын
@@josephschweikhardt Nope. Been waiting for reply. If you find anything let me know!
@robherrmann1180 Жыл бұрын
What size wire? Hoping to grab it before I get the boat out of storage and don't know what's in there
@omieyouknowme
Жыл бұрын
I used what I had which just 16gauge trailer wire. Pretty sure the wires in there are 18gauge
@robherrmann1180
Жыл бұрын
Thanks!
@robherrmann1180
Жыл бұрын
@@omieyouknowme So, have any way to hook up so the wiring always stays connected for ipikot and the foot pedal? I was think of building a Y adapter coming from the trolling motor and splitting so I can connect each control. So all I have to do is flip the switch and tooth the door control and ipikot remote are already to go. Not sure if it can work that way. Also not sure how hard it would be to make a Y adapter with the minnkota plugs
@omieyouknowme
Жыл бұрын
@@robherrmann1180 I looked at this building a y cable the cost effort is not worth it. Buy the terrova control board it comes with y cable
@sawyerfuller4805
Жыл бұрын
Couldn’t you just cut the wires going to the plug and slice in another plug so you have two plugs coming off the cord
@jakehudson84752 ай бұрын
Is there anyway my father-in-law can get ahold of you, he is having problems doing this to his trolling motor.
@omieyouknowme
2 ай бұрын
I am not the expert, just posted how I did this. What is he having issues with? Is he upgrading from an older motor like I did to full Bluetooth and new control board?
@chip1020cg Жыл бұрын
Hey partner I have the exact same situation is it possible for you to draw out a schematic
@omieyouknowme
Жыл бұрын
Ya it's in my list of video to make. Right now my boat is down once it's in water I'll.get one drawn up and show hos this works.
@benjaminhurt7480 Жыл бұрын
Can I do this with a factory powerdrive with ipilot?
@omieyouknowme
Жыл бұрын
You should be able to, as long as you have the foot pedal with matching 5 pin plug. The internals for power drive with and without I pilot is same. If you have co pilot those are different
@jost6953
Жыл бұрын
Did you do it. I just bought ipilot Powerdrive I haven’t looked at it yet but it might not have the end for the foot pedal that come out of the motor
@omieyouknowme
Жыл бұрын
@@jost6953 no it's snowing here and 16 deg right now
@omieyouknowme
Жыл бұрын
@@jost6953 if your I-pilot from the head goes to main control panel has a round connection that you can unscrew that's where foot pedal would go. Then you would need to add a dpdt switch inline. I'll make another video of this soon as it warms up
@jost6953
Жыл бұрын
I meant to ask Benjamin if he did it to his ipilot after looking at it, it does have the plug so I would have to assume that it is %100 able to be done to factory ipilot. Mine is brand new though and I’m not sure I want to void the warranty so I don’t think I will do it after giving it some thought
@evanblackwell7008 Жыл бұрын
Can you post a better picture of the wires for the middle prongs off the switch on yo ur board
@omieyouknowme
Жыл бұрын
There is only a black and white wire that's steering motor wire from the board to motor. Those are the only two that matter
@evanblackwell7008
Жыл бұрын
@@omieyouknowme can you post a picture I took the black and white and connected it to one side of my switch then done the other 2 wires then when it come to the wires for the steering of my foot pedal I can only get it to turn one direction not both
@evanblackwell7008
Жыл бұрын
@@omieyouknowme your board wires are white and red correct? I have a red ,brown, green, yellow coming off my board that’s available unless I splice into the set that I assume is for the remote functions
@omieyouknowme
Жыл бұрын
@@evanblackwell7008 those are for auto pilot or other features. Don't touch those
@omieyouknowme
Жыл бұрын
@@evanblackwell7008 your black and white from motor go to middle of switch on either side. Then the black white from board goes to one side of switch same for wires from I-pilot. I can draw up a diagram this weekend
Пікірлер: 56
I just ordered my i-pilot upgrade and got it today, started installing it and I hit this dead-end realization. My brain starting turning (before watching this video) and this is exactly what I came up with in MY mind... I have to work early in the morning and the trolling motor is still laying in the livingroom lol the wife hates it but she's gonna have to deal with it for a day 😅 Good video! 👍
@omieyouknowme
Жыл бұрын
I was about to break out the fluke and make a y cable, but this was so much easier.
Thanks man! You solved my problem!
Thank you. Now i need to find me a electrician to hook this up.
@omieyouknowme
Жыл бұрын
Watch the follow up video. I have paper diagram even a caveman can follow
@paulbowman3845
Жыл бұрын
LOL. Im no electrician for sure.
What color are the wires that are coming out of the board for connecting the foot pedal? Read through some of the other comments -I do not have a black and white wire coming from board. I just have Green, Yellow, Brown and Ref. I have a 24v Powerdrive and am trying to do this set up but can’t figure out where my bottom set of wires are supposed to connect for the using the foot pedal.
@omieyouknowme
3 ай бұрын
The wires that come from the steering motor. They are usually black and white for all the motors I have worked on. It may be going to the main board instead of power head.
By adding the switch, does this allow you to use both remote and foot pedal without having to swap out the plug each time?
@omieyouknowme
4 ай бұрын
No you still have switch plugs. The switch is there so you don't have to remove cover to swap steering wires inside.
Did you draw up a diagram as you said in other comments? I understand the switch locations for the white and black from the steering motor to the ipilot but I cannot tell what you are connecting on the other side of the switch for the actual foot pedal side of switch. I’m trying to complete this weekend so if you do have a diagram drawn could you please post or send to me. Thank you!
@omieyouknowme
Жыл бұрын
Will get diagram drawn up and uploaded by end of day.
@patrickgarstecki9055
Жыл бұрын
Thank you
I wired up my DPDT switch with motor wires as my line side of switch and I-pilot wire and foot wire to load side of the switch. Both i-pilot and foot control work but it does not matter how the switch is positioned. They both work in any switch position. Am i missing something.?
@omieyouknowme
Жыл бұрын
The middle terminal of switch go to the steering motor, then one side of switch goes to the wires coming from board the other side of switch go to the I-pilot wires.
Hi, just bought footpedal no pdV2 with bluetooth, can you run footpedal with ipilot in parallel? I think the switch have not much use if you need to plug ipilot or footpedal anyway…
@omieyouknowme
Жыл бұрын
You can run one or the other not in parallel Have to change out the round plug for I-pilot or foot pedal.
I see the black and white coming from the ipilot to steering motor. But we cannot tell the color of the other two wires coming from the board that will wire to the other side of the DPDT switch. Can you clarify the colors, please,
@omieyouknowme
Жыл бұрын
It should be black and white from the board as well. Match the black to black and white to white on the switch. Ignore my green yellow just wires I had laying around.
@mulewrangler1
Жыл бұрын
@omieyouknowme thanks. I think we must have a later model board bcx we don't have a black and white coming from the board.
Anyone done this with the newer control board with the green,yellow,brown and red wires? I got the switch in but can’t figure out how to configure those into the foot steering portion. Thanks for any help!
@josephschweikhardt
5 ай бұрын
Every figure this out? I’m running into same situation I have red and green plugged in and can get the motor to turn right but can’t get it to go left. Any tips would help
@caydenhomolka2408
5 ай бұрын
@@josephschweikhardt Nope. Been waiting for reply. If you find anything let me know!
What size wire? Hoping to grab it before I get the boat out of storage and don't know what's in there
@omieyouknowme
Жыл бұрын
I used what I had which just 16gauge trailer wire. Pretty sure the wires in there are 18gauge
@robherrmann1180
Жыл бұрын
Thanks!
@robherrmann1180
Жыл бұрын
@@omieyouknowme So, have any way to hook up so the wiring always stays connected for ipikot and the foot pedal? I was think of building a Y adapter coming from the trolling motor and splitting so I can connect each control. So all I have to do is flip the switch and tooth the door control and ipikot remote are already to go. Not sure if it can work that way. Also not sure how hard it would be to make a Y adapter with the minnkota plugs
@omieyouknowme
Жыл бұрын
@@robherrmann1180 I looked at this building a y cable the cost effort is not worth it. Buy the terrova control board it comes with y cable
@sawyerfuller4805
Жыл бұрын
Couldn’t you just cut the wires going to the plug and slice in another plug so you have two plugs coming off the cord
Is there anyway my father-in-law can get ahold of you, he is having problems doing this to his trolling motor.
@omieyouknowme
2 ай бұрын
I am not the expert, just posted how I did this. What is he having issues with? Is he upgrading from an older motor like I did to full Bluetooth and new control board?
Hey partner I have the exact same situation is it possible for you to draw out a schematic
@omieyouknowme
Жыл бұрын
Ya it's in my list of video to make. Right now my boat is down once it's in water I'll.get one drawn up and show hos this works.
Can I do this with a factory powerdrive with ipilot?
@omieyouknowme
Жыл бұрын
You should be able to, as long as you have the foot pedal with matching 5 pin plug. The internals for power drive with and without I pilot is same. If you have co pilot those are different
@jost6953
Жыл бұрын
Did you do it. I just bought ipilot Powerdrive I haven’t looked at it yet but it might not have the end for the foot pedal that come out of the motor
@omieyouknowme
Жыл бұрын
@@jost6953 no it's snowing here and 16 deg right now
@omieyouknowme
Жыл бұрын
@@jost6953 if your I-pilot from the head goes to main control panel has a round connection that you can unscrew that's where foot pedal would go. Then you would need to add a dpdt switch inline. I'll make another video of this soon as it warms up
@jost6953
Жыл бұрын
I meant to ask Benjamin if he did it to his ipilot after looking at it, it does have the plug so I would have to assume that it is %100 able to be done to factory ipilot. Mine is brand new though and I’m not sure I want to void the warranty so I don’t think I will do it after giving it some thought
Can you post a better picture of the wires for the middle prongs off the switch on yo ur board
@omieyouknowme
Жыл бұрын
There is only a black and white wire that's steering motor wire from the board to motor. Those are the only two that matter
@evanblackwell7008
Жыл бұрын
@@omieyouknowme can you post a picture I took the black and white and connected it to one side of my switch then done the other 2 wires then when it come to the wires for the steering of my foot pedal I can only get it to turn one direction not both
@evanblackwell7008
Жыл бұрын
@@omieyouknowme your board wires are white and red correct? I have a red ,brown, green, yellow coming off my board that’s available unless I splice into the set that I assume is for the remote functions
@omieyouknowme
Жыл бұрын
@@evanblackwell7008 those are for auto pilot or other features. Don't touch those
@omieyouknowme
Жыл бұрын
@@evanblackwell7008 your black and white from motor go to middle of switch on either side. Then the black white from board goes to one side of switch same for wires from I-pilot. I can draw up a diagram this weekend