Mind-Blowing Woodworking | Building a Tensegrity Table
Тәжірибелік нұсқаулар және стиль
How does this display table hold itself up? Find out in this video, where I build a piece of furniture known as a tensegrity table.
Tensegrity structures are ones which rely on tension to maintain stability. This tensegrity table is built out of scrap walnut, fishing line, and a few brad nails.
I designed the wooden components of this table myself, but was very heavily inspired by a 3D printed table I saw on KZread by a creator named Seabird HH.
I made and repaired a number of mistakes during this build, which was definitely more difficult and stressful than my usual builds due to the experimental nature. The main mistake, shown in the intro, was using mortise and tenon joinery with structurally weak cross-grain tenons. In retrospect, I should have just glued the hook shaped piece directly to the surface, since it is a face-grain to face-grain joint.
Thanks for watching. Feel free to leave a comment with your thoughts, and don't forget to subscribe if you like content like this!
** Want to buy the tools and accessories I use in my videos? Here is my Amazon affiliate store where you can get them for yourself! www.amazon.com/shop/dkbuilds
--------------
Support me on Patreon here: / dkbuilds
Check out my instagram page here: / dkbuilds
Or my facebook page here: / dkbuilds
Or my Etsy shop here: www.etsy.com/shop/DKBuildsWoo...
--------------
#dkbuilds #tensegrity #mindblowing
Пікірлер: 722
Very refreshing to watch a video with only sounds of a woodworker at his trade. No flashy graphics, no annoying dance music over the vid and no constant chatter about nothing. You have a new subscriber.
@dkbuilds
4 жыл бұрын
Thanks, Derek!! I've been getting lots of similar comments, so I'm going to focus on making similar videos from now on. Welcome to the channel!
@hughtub
4 жыл бұрын
Oh come on, don't you want a 30 second introduction "HEY GUYS WELCOME TO [camera change] DK BUILDS [camera change] ON TODAY'S SHOW..."
@chriswebster24
3 жыл бұрын
That was the only thing I didn’t like about the video. I have a harder time dancing while I watch without any dance music playing. I mean I still did it but it was a lot more difficult.
@remlikamel1866
3 жыл бұрын
Pp
I think everyone has that moment during a project when something doesn't go right and you question every decision you've made bringing you to that point. And all you can do is accept it and figure out how to fix it. Great job. I'm not a wood worker so everything you did in this video is sorcery to me. Very cool end product.
@dkbuilds
4 жыл бұрын
Totally agree John, mistakes are a part of life, and overcoming/fixing them can be tough but is better than giving up. Thanks for watching, I'm glad you enjoyed it!
@peterparker8462
4 жыл бұрын
Nice 5 stages of grief cameo😉
That "oh nooo" at the beginning is all of us. Great work!
@dkbuilds
4 жыл бұрын
Haha thanks Anthony! There were several more such moments but with much more vulgar language so I had to leave them out 😇
@stewartmcmanus3991
4 жыл бұрын
It sure is, carefully plane and sand one side, then screw and glue the wrong side !!!
@9The0Unknown7
4 жыл бұрын
Stewart McManus or have it all planned it and start assembling and you are back and realized you flipped a piece at some point and didn’t flip it back and it’s too late now. It’s a feature. No one else will know, but you will.
@ballspector
3 жыл бұрын
I don't get it
@MRMeaws
3 жыл бұрын
Smooms bruh
No obnoxious music in background and no unnecessary explanation about every move you make. You sir are the 1% who knows how to make videos. Great work 👍
this is so beautiful, really beautiful. the most beautiful "floating" wood work, I've seen so far.
LOVE the format, dude. Not a word spoken, yet concise, and I could tell what your intention was in every shot. Keep it up. Got my sub.
Amazing work!! I’ve watched this a few times and my brain is still not capturing how this is even possible.
Love seeing your projects, your content is really refreshing. Looking forward to future builds!
@dkbuilds
4 жыл бұрын
Thanks Maria!! Happy to have you as a viewer. More videos are coming for sure!
Gyönyörű videó! Mindent pontosan bemutat, és nem tereli el a figyelmet semmilyen idegesítő zenével. Köszönöm! Thanks!
@dkbuilds
4 жыл бұрын
Nagyon szépen köszönjük! Örülök, hogy tetszett a videó!
Man when I heard that snap I felt it. Even better recovery. Thanks for the great video.
@dkbuilds
4 жыл бұрын
Haha thanks A.J.! Appreciate you watching!
This is how these videos should be edited. No music, no chat, just work (and the occasional mistake 😅). Great work. But you already know that.
@dkbuilds
3 жыл бұрын
Awesome thank you Usuario! Glad you liked the video style!
This was mindblowing! You've inspired me to make one myself
@dkbuilds
4 жыл бұрын
Do it, Frank! And let me know how it turns out 👍
Amazing work!! I love it I might try this myself
11:29 - Whew!!! Is spot on! These suckers look awesome and freaky, but they are a PAIN at times. I made a triangular tensegrity stand for a pyramid clock (wood base, but paper pyramid holding the clock), and the centre of gravity of an equilateral triangle is indeed it's "centroid", but the other triangles are 1/3 from the base, not necessarily their centroids. The base is smaller than the upper deck. Looks really cool! Dude, outstanding work on this!!! Thank you for sharing!
@dkbuilds
4 жыл бұрын
Very cool Thomas your triangular table sounds awesome. Great idea to hold a clock. Thanks for watching!
Just AMAZING!
Tensegrity is so inspiring. Makes me want to make my own designs.
@dkbuilds
3 жыл бұрын
Thank you! Do make your own and share with me the results so I can be inspired by you!
Hats Off 2 U Dude, Great Art Of Wrk 👌👌👌
nice video.. i like how you show the humanity, the mistakes and the way you see to the front and solve it.
@dkbuilds
3 жыл бұрын
Thank you very much! I'm glad you liked it, UirUmarU! :)
As a mate of mine says: Patience and perseverance took a snail to Jerusalem! Nice piece.
@dkbuilds
3 жыл бұрын
Nice saying, Kielan! Thanks for watching!
Very nice. You did a great job show how and what you did to create this fantastic conversation piece. No question people are going to talk about your creation. You did a great job editing your video and your woood working skills are excellent. Thanks for taking the time to show us what you did. From Missouri USA
@dkbuilds
10 ай бұрын
Thanks so much Jack, I appreciate you taking the time to watch and comment!
That is so cool - it looks so stable - amazing.
@dkbuilds
4 жыл бұрын
Thanks, H! It is quite stable!
Impressive build! Looks incredible.
@dkbuilds
4 жыл бұрын
Thanks for the kind words, Jason!
Hola desde Argentina!!!solo aplausos hermosísimo trabajo!!!te felicito!!abrazo desde América latina
@dkbuilds
3 жыл бұрын
¡Muchas gracias Aries! ¡Saludos desde Estados Unidos!
It can be made larger for coffee table, I believe. awesome idea, man.
Bloody brilliant, great job.
@dkbuilds
4 жыл бұрын
Thanks, Sommer!! Turned out better than I even hoped :)
I get it and understand it (mostly) but it still blows my mind. And yes, daily dose enlightened me to these. But cool channel format, subbed
@dkbuilds
4 жыл бұрын
Thanks Weaboo! Happy to have you here!
Had to pause for a while when it was done. Masterfully my friend, masterfully executed.
@dkbuilds
4 жыл бұрын
Thanks, helyllefilten! It takes a while to think about and understand how it works for sure!
I’m as equally amazed at the build as I am at the diy compass hack o_0
This was definitely a fun build! How did you tie off the knots so the tautline doesn't loosen/tighten after it's done?
Imagine having a dinner table and chairs like that, would be really sick
@springbooksh
4 жыл бұрын
So don't imegine
@NoobSharkYT
4 жыл бұрын
Thank for idea I made one
@arigatoespacialsuperadmiti7316
4 жыл бұрын
@@NoobSharkYT One table? That sounds really cool
@arleigh_camp
4 жыл бұрын
This person did, and he can stand on it! Check it out: kzread.info/dash/bejne/e46Ira5tlpbHqqQ.html
@afiqputra9076
3 жыл бұрын
You can make it but just make sure the tension of the string or cable in the middle is strong enough to withstand every weight that are stacking on top of the table. You don't want it to snap and have your dinner on the floor lol
Absolutely Amazing....
@dkbuilds
4 жыл бұрын
Thanks Delores! 🙏
Excelent work I Love it !!!
Awesome job what a great project
@dkbuilds
4 жыл бұрын
Thanks Bryan! Glad you liked it 😃
I felt sure at 10:23 the short grain would break again! Nice job on some fiddly small components.
@dkbuilds
3 жыл бұрын
😇
You could have hidden your mistake, just glued over and no one would ever know. But instead you displayed it proudly. That makes you better than most men.
Fantastic work, dude! Really amazing results! 😮 I would never try something like that! 😂😂😂😂😂 Stay safe there! 🖖😊
@dkbuilds
4 жыл бұрын
Thanks MC, I appreciate it! Stay safe yourself!
I feel you at that “oh noo.”
@dkbuilds
Жыл бұрын
😂
oh no you got there in the end Tensegrity there is so many many creative minds at work creating these great talking points for any/every home..I am addicted to watching you may too L.O.L.
@dkbuilds
3 жыл бұрын
Haha thanks Michael! Thanks for watching!
@Uniquettt
3 жыл бұрын
@@dkbuilds Much better viewing then the news
thanks for sharing...amazing works...
@dkbuilds
4 жыл бұрын
Thanks for watching, Ferdy! I appreciate the kind words :)
Muito bom, parabéns pelo trabalho amigo.
Nicely done
I need this table dude, its awesome
@dkbuilds
4 жыл бұрын
Thanks Ariel!
Great work. Thank u. God bless u
@dkbuilds
3 жыл бұрын
Thank you Antonio! :)
I like everything made of wood because it makes me feel healthy.👍
@dkbuilds
4 жыл бұрын
It is a very natural and healthy material, I agree!
@chriswebster24
3 жыл бұрын
I bet the poor tree felt differently as it was savagely murdered and then its body was disfigured. RIP Tree. We will never forget you.
OMFG.....THAT "OOOHHH....NOOOO" Voice clip at the beginning sums up so many of my tensegrity projects. Lmfao and our methods are nearly identical all round. Props to ya man.
@dkbuilds
3 жыл бұрын
😆 Thank you EP! Good luck with your own tensegrity builds!
All that hard work deserves a like and sub
@dkbuilds
4 жыл бұрын
Hey thanks, Jake from State Farm! Happy to have you around 😀
You know, I never thought of using a table saw for cuts like that - I always use the bandsaw and make lots of diagonal cuts to remove material, and the inside surface requires a lot of fiddly sanding to make even. Nice little table! Oh wow, and it just occured to me that I can use this trick to fix a notch that I need to deepen in a piece I had already glued together. As it stands, I can't get the piece where I want it because the other sides are in the way, this just might work. Thanks for showing a different way to use a tool!
@dkbuilds
4 жыл бұрын
Glad you picked up something from the video, Peevester! This method is how I make a lot of dados and tenons on the ends of pieces of wood. Make sure to hold it very securely though, I always use a cross-cut sled because it supports the wood on both sides of the cut. Stay safe, and let me know if you successfully fix that notch!
@peevester9987
4 жыл бұрын
@@dkbuilds It worked! It took about 2 minutes to make the cut, and the result looked better than the original notch I had cut with a bandsaw and diagonal cuts. So long as you square up each side with the fence first, this is a very handy trick. Thanks again!
Great work
The only people that don't make mistakes are those that never make anything... Thumbs Up!
That is SO COOL !!!!!! Got to try it.
@dkbuilds
3 жыл бұрын
Thanks, gtx! If you try it, let me know how it turns out!
Very well done my friend!
@dkbuilds
4 жыл бұрын
Thanks, Andreas!
Amazing...Good work...
Such a big worrk... felicitations.
@dkbuilds
3 жыл бұрын
Thank you, Caleche!
Great craftsmanship! How does it perform with temperature variations? Do any of the lines sag when it's hot? Did you allow for that, if so, how?
Good work.
Seems very easy. But actually it's not that. Thanks for making this video man!
Cool ... great job 👍
That is impressive. I just subbed because you got very cool vids and ideas. I consider myself a woodworker, not the best but I've put together a few pieces I'm very proud of but I can't figure out how the hell top of that table IS STANDING!!
@dkbuilds
4 жыл бұрын
😅
Beautiful!
@dkbuilds
Жыл бұрын
Thanks Joel! :)
Parabéns ficou uma bela obra de arte
@dkbuilds
4 жыл бұрын
Muito obrigado!
this is great man! :D i hope your channel prospers
@dkbuilds
4 жыл бұрын
Thanks for the support!! Me too :)
Dude I can't even begin to describe how awesome this really is, seriously, if it's not your main money earner it should be, look at your end product online.... bizarre yes... fascination .... yes, essential for your home .... yes
@dkbuilds
3 жыл бұрын
Thanks Patrick! Maybe I'll try to figure out a way to mass produce them :)
I think another cool effect would be to have a small chain for the outer lines. It would exaggerate the effect. Well done!
Good job 👍
Work of art👍
@dkbuilds
3 жыл бұрын
Thank you for the kind words, PB!
Loved your work and your video!
@dkbuilds
2 жыл бұрын
Thanks so much Mitsos!
Genial parcero quedo guay
Отличная работа,благодарю за ролик удачи тебе
@dkbuilds
3 жыл бұрын
Спасибо за просмотр и удачи!
best intro to a DIY video
@dkbuilds
4 жыл бұрын
Thanks 😜
Aside from the obvious, some great machinery in this video and even greater dust extraction kit!!
@dkbuilds
3 жыл бұрын
Thanks so much Jon!
11:26 , that moment when it snaps into place just seem so surreal.
@dkbuilds
4 жыл бұрын
I know, right! I looked straight at the camera in amazement.... I really was not expecting that to happen.
Wow nice sharing..
Love this idea and design. I'd be locking up all sharp objects in my house if I had that lol
@dkbuilds
4 жыл бұрын
😂
@skolisse1
4 жыл бұрын
The design is from JK Brickworks. kzread.info/dash/bejne/aKyW0NR-obDYZbw.html
Sweet job! I just love the fact that you kept pushing through the hiccups. Hey, quick question, I'm making a similar piece, would you say it's critical to the integrity of the piece to double up the center thread ? I wanted to try with a single thread, just as a matter of looks. Cheers from chilean patagonia!
@dkbuilds
4 жыл бұрын
Thanks for watching Jonathan! Whether you need a single thread depends how strong the thread is. It needs to be able to hold the whole weight of the top of the table plus what you put on the table plus a little more from the four strings pulling downward. My fishing line was weak so I doubled it up, but if you use stronger string a single one should work. Good luck!
This is so awesome!
@dkbuilds
4 жыл бұрын
Thanks, Jody! :)
Dude's got all the tools!
@dkbuilds
3 жыл бұрын
💪
Felicitaciones. Desde Argentina!!
@dkbuilds
Жыл бұрын
Gracias!
rlly neat design
@dkbuilds
2 жыл бұрын
Thank you Luca!
After closely monitoring the whole project.... I must admit.. I fucking love it Great job mate
@dkbuilds
4 жыл бұрын
😂Thanks John!
Cool design! I'm going around a bunch of tensegrity making videos at the moment because I'm planning on making something similar myself. I have to say this is the most impressive so far, as it looks very stable and your method of tying off the lines is the neatest I've seen. Any tips for making or design changes if you made it again?
@dkbuilds
3 жыл бұрын
Thanks, Nothing! I'm actually really happy with this design, I wouldn't change anything I don't think!
That's really neat
@dkbuilds
4 жыл бұрын
Thanks Lord!
This is beautiful ❤️
@dkbuilds
3 жыл бұрын
Thank you Beatbender!
willlll soooooombody PLEAAAASEEEE!!! get this man a mallet...
Great work. It's awesome
@dkbuilds
3 жыл бұрын
Thanks a lot Chris 😊
It's beautiful.... 🤩
@dkbuilds
4 жыл бұрын
Thank you, Soumya!
*Great* _Design_
@dkbuilds
4 жыл бұрын
Thanks! :)
Loved that stand glad my daughter can't see it I would get DAD pretty please what marker pen are you using Regards Steve from crazy UK London
Nice work!
@dkbuilds
4 жыл бұрын
Thanks Terri!
Cool, David. Hadn't seen this sort of thing before. I gather the name comes from "tension' somehow? Love the 5 steps of grief part. lol. One tiny little tip for you, as I had run into this in the past. When you were holding down the piece and trying to scribe a line around for the mortise, a very tiny spot of CA glue will hold it in place long enough to get the lines scribed. Then with such a small drop of glue, it breaks off easily without issue. After many times having something slip while holding it, I tried that. Forget where I originally saw it mentioned, but it works like a charm.
@dkbuilds
4 жыл бұрын
😂Glad you liked it Don! Always love seeing you in the comment section. I think the name is a combination of "tensional integrity"... to be honest I had never heard the word before I started googling for what to name this project!
@dkbuilds
4 жыл бұрын
Oh sorry I missed the second half of your comment. That's a great trick! I will definitely try it. Do you use accelerants with your CA glue to get it to dry faster? I've been meaning to buy some but haven't gotten around to trying that out yet.
@DonsWoodies
4 жыл бұрын
dk builds yep, I do use accelerant most of the time. I don’t use it when I need a little time For positioning. What you were doing would be one of those times when I wouldn’t. Tried all kinds of CA glue over the years including some exotic stuff from Loctite when I was in a machine shop, but my favorite right now is the 2P-10 stuff. Can’t say I’ve doing clinical trials, but my gut instincts is that it’s slightly better than others I’ve used. Just used it a few minutes ago making a little standoff For my table saw for cutting off pieces with a miter gauge. I’ll send you a picture of what I mean
@BhriguBharadwajPant
4 жыл бұрын
TENsion + inTEGRITY = tensengrity
Every tool is a hammer.
Nice!! I just made one of these tables from spare plywood, string trimmer line and some rusty wood screws. I made one because I didn't believe it would hold up anything and I was wrong! They come together pretty quickly and surprisingly sturdy provided you secure all the cables. I rigged mine like you'd rig a sailing ship--in one hole, out the other. The whole thing came together in about two hours. The next one I make will look more like yours. Nice job, I got some tips from how you did it.
@dkbuilds
4 жыл бұрын
Awesome, sounds cool Alex! Yup I first made a prototype a lot like you did, I only filmed this one. Let me know how your next one turns out!
This is like asmr for engineering enthusiasts that don't buy into the asmr hype
Excelente trabajo saludos desde ciudad de Salta Argentina
@dkbuilds
3 жыл бұрын
Muchas gracias Sergio!
For the extremely fine motor skills around 9:30 the best tool is probably eyebrow tweezers! I use them all the time in sewing.
@dkbuilds
4 жыл бұрын
Good tip, tilly! I need to buy some XD
Beautiful
@dkbuilds
2 жыл бұрын
Thank you Wilson!
Brilliant
Great looking project! I know it would spoil the effect in a way, but I couldn't help thinking how it could look really cool with low power led mounted in the bottom to shine up through the fishing line like fiber optic cable.
@dkbuilds
4 жыл бұрын
That's a great idea! Thanks for sharing!
Really cool spin on the design. Looking for inspiration on a steel one I'd like to make. MIG wire will take gobs of tension.
@dkbuilds
3 жыл бұрын
Wow yeah I bet that could hold a ton. You need a way to individually tighten each of the outer wires though to balance it... could you do that with MIG wire?
So cool!💜
@dkbuilds
3 жыл бұрын
Thanks Jason!
Paid-off and was worth the effort. The hardest part is holding everything in its "final" position while stretching the threads. Two hands are just not enough...
@dkbuilds
4 жыл бұрын
I agree... it was quite frustrating to assemble. Thank you for watching and commenting!