Wonderful. My stepson has one of these he using on work sites in the tropics here in Australia.. Pretty sure this will fix it. Parts ordered. Wonderful video. Congrats!!

@BuyitFixit

Жыл бұрын

Thanks Mike. If you still have problems give me a shout as I've repaired 2 of these with similar faults but different causes. Check my other video just in case it's the other fault.

A nice in depth fix, grand job 😊👍

@BuyitFixit

5 ай бұрын

Thanks 👍I did another one for a friend which had a different fault too 🙂

Great fix as always, keep up the good work. Very informative

@BuyitFixit

2 жыл бұрын

Thank you Scott!

Fascinating -thank you for sharing

@BuyitFixit

7 ай бұрын

Glad you enjoyed it👍

Awesome video yet again.. so if you had just changed the zennor diode would that have fixed it ? have you repaired one yet which doesnt work on battery but does on 240 ?

@BuyitFixit

2 ай бұрын

Thanks 👍If I remember right it was the volume control IC got fried by the faulty zener (hopefully this is the right video as I've fixed two of these) The other one was a faulty transistor for the 240v switch over which seems to be the opposite of the fault you describe although it may be useful still as I'm sure I work out where different voltages go.

@robinafandale

2 ай бұрын

cheers. I'm looking to buy a radio and I've seen 3 for sale now work on 240 but not on 18v.. keep up the good work 😊

What is your opinion of "power screw drivers?" I find mine to save a bunch of time and they (i have 2) do not over torque the screws either.

@BuyitFixit

5 ай бұрын

I've never been a fan of them, I always like to feel how much pressure are on the screws. Perhaps I'm just old and stuck in my ways 😂😂😂😂

Too Bad you Don't Have A Magnetic Dish. They Realy Come In Handy. Cause when I'd Take Something Apart Got So Tired Of Loosing Screws. Then I Seen One Amazon I Thought I'm Getting One Of Those. & Now I'm Glad I Bought It.

@BuyitFixit

6 ай бұрын

Thanks for the suggestion Roger. I actually do have one, but normally use it when working on the cars or tractors. The blue mat I use actually has magnets built into some of the compartments around the edges (I just keep forgetting to use them 😂😂😂😂).

Hi. I have the same radio JSR dab+ never used outside only in the house and not moved. All of a sudden the dab signal keeps dropping out making it not possible to listen to. Many thanks for your interesting videos.

@BuyitFixit

5 ай бұрын

Thanks 👍I'm not sure what could be causing the signal problem. Are any other DAB radios having the problem? Could it be interference from an external source?

Great job. Looks like your chip that you ordered were fakes??

@BuyitFixit

5 ай бұрын

Thanks 👍Yes, that was what I thought too!

i'm not sure how you fixed it?,did you replace that chip?

@BuyitFixit

10 сағат бұрын

Yes, and a resistor (if I remember as it was a while ago) 👍

The sound on this is easily overcome on the worksite.. any ideas on how to boost the lousness

@BuyitFixit

7 ай бұрын

Unfortunately not, the speakers would only be rated to take a certain amount of power. You would need to fit a larger (or external amplifier) with some larger or external speakers connected to it.

Hi, back side, torx or Phillips?

@BuyitFixit

Жыл бұрын

Torx and a VERY long one. I had to buy an extra long torx specifically for this.

@frodemolland6249

Жыл бұрын

@@BuyitFixit ok great 😁 I have ordered a set of 6 250mm screwdrivers

@frodemolland6249

Жыл бұрын

Hi again, I Watch Your videos Almost everyday 😁 Great work, much inspired

@BuyitFixit

Жыл бұрын

Thank you 👍comments such as yours are what inspires me to keep producing videos. Thanks again Frode Molland👍

@garylee7670

6 ай бұрын

⁠@@BuyitFixithi what size of torx driver do you need for the fixings deep in the radio

This exact problem has happened to my Milwaukee radio today would you be able to fix it?

@BuyitFixit

2 жыл бұрын

Hi, sorry I don't actually run a repair shop. My video's are to help you to be able to repair stuff yourself. If are wanting to have a go yourself I should be able to help or I can offer advice.

@jordanbuckett6850

2 жыл бұрын

If you have a link to the parts you bought it would be really helpful?

@BuyitFixit

2 жыл бұрын

The part that I used to fix this radio is this one here: www.ebay.co.uk/itm/293243389191 It's a PT2314 which is the same as the original SC7314 just by a different manufacturer as the SC7314 I received seemed to be fake. But before ordering parts I'd check what power is going to that chip. Is the 22ohm resistor burnt? I fixed another radio with a SIMILAR issue, but it was actually a different problem. The problem on the other radio was a relay not clicking in due to a blown transistor on the power supply. Do you hear a "click" from a relay when you turn the radio on when plugged into the mains and you turn the power switch on the front on? If so then that transistor would appear to be working ok. Hope that helps!

@jordanbuckett6850

2 жыл бұрын

I just got to work and interestingly i turned it on and it just started and works fine again I don’t have the problem like I had yesterday

@frodemolland6249

Жыл бұрын

Hi, Just got the defect radio in the mail today, got similar error l Ike the one in the video, freezes When turning on Volume. It does make a clicking Sound When turning Volume. Could it just be the pt2314?

Very single Milwaukee tool I have is junk!

no sound