The mevotech green/premium is really good . The classic/blue line is shabby

Installing some TTX on my Tacoma this weekend

Moog is now at a level with dorman

Tried putting upper ball joints on my Toyota Pickup and the Moogs wouldn't even fit nor did the boots fit properly.

@MegaMarclar

3 ай бұрын

I bet the moog joints were knurled too, ya low quality chinese crap.

Just one brand/maker isn't the end all it used to be...now we gotta shop this brand strut, that brand knuckle, etc..shop smart my automotive kindred!!

They look like gooder quality over stock

@MegaMarclar

24 күн бұрын

depends on the application, but in general I avoid moog at all costs, I'm tired of filing warranty claims.

There’s still some moog USA made stuff floating around if you get lucky the mom and pap shop might have some still on the shelf. I found upper and lower control arms for my truck still made in USA just look at the box before you buy.

Having been around a while,but not needed to replace normal wear parts for years, I go to look into Moog and I’m surprised to hear all the negative. They used to be top of the line and correct deficiencies in stock parts! Sad… I have a JL wrangler that I’m going to install a TTX inner/outer tire rod on. I’m hoping it’s at least as good as stock because stock is way more expensive. Same for aftermarket “upgrades”.

@MegaMarclar

Ай бұрын

A lot of those old brands.. MOOG, Gates, Yukon, Redhead,... all betting on their old reputations, selling crap Chinese parts now. Its really sad to watch.

Anything blue booted mevotech is pure garbage. The TTX mevotech is 👍 good stuff.

Ttx is the great

I use Mevotech and just installed some more of their stuff. But I replaced a control arm on my wifes car with Mevotech and within a year and a half the Ball joint was completely sloppy and moving freely, making a ton of noise. Put some OEM ones back in.

@MegaMarclar

19 күн бұрын

there are different tiers of mevotech parts. Some are lower quality.

Looks prety good, moog is shit. I did buy Timken Bearings, they move the space shuttle and my car! Looking for stabilizer links.

@Munky332

Ай бұрын

my Timken bearing I just put in my 04 avalanche came from korea. Not sure how much better that is over china... Why can't we have decent products any more?

Is TTX all we have left in terms of quality?

@MegaMarclar

2 ай бұрын

apparently, everything is chinese now. all the big manufacturers sold out.

@martyno8696

2 ай бұрын

@@MegaMarclar much like the rest of the country.

mevotech ball joints tie rods are also made in China

@DaveDavis-ml5ic

9 ай бұрын

I just bought a really nice alternator. W.A.I. Global brand. it's also made in China but it runs like a top and is quiet no sound.

@MegaMarclar

9 ай бұрын

everything is made in china, some to different price points than others.

Thoughts on Mevotech Supreme products?

@MegaMarclar

9 ай бұрын

I use a lot of the TTX series, have not tried any of the other product lines much. But in all reality most everything is built in china anyway.

@Killian665

Ай бұрын

They’re junk. I had 2 brand new lower ball joints fail on a Honda in 4 months. When the originals lasted over 30 years. Whole joint just pulled apart in a parking lot luckily

@lucid484

24 күн бұрын

@@Killian665 Same thing just happened to me, Mevotech ball joint toast after a year nd a half.

Mevotec is junk I put brand new control arms on a Honda they were makeing noise brand new out the box

@MegaMarclar

9 ай бұрын

that really means nothing. probably installed them incorrectly.

@shyne5637

9 ай бұрын

@@MegaMarclar impossible one garage did them for me then I warrentied them out then my dad did them for me tightened them all on the ground and all I Ben working on cars for 30 years now

@Kavie93

7 ай бұрын

Which mevotech line did you buy? Because they offer 3 different brands…..

@lifegoeson4085

4 ай бұрын

​@@shyne5637Moog control arms are better, I use carquest upper control arms made by Moog