I love watching your videos. They take me back to my days in foundry and machine shop back in school, and remember back when my dad was an apprentice machinist. I still get excited whenever I'm in a shop and wish I had one of my own to work with (along with the time to tinker).

M.A.G.N.I.F.I.C.E.N.T A treat for the eyes & brain and a joy to last forever!! Thanks so much.

this guy's a pro. Since computers this tecnology is practically lost Good to see someone reviving casting

@jpeterman6178

4 жыл бұрын

I agree.

@Juklitz282

4 жыл бұрын

Is not, that´s a belief. There´s plenty of manual engineering work, it´s not effective to have CNC, water, lasers for smaller production, tool maintenance etc. It´s not that visible, but still exists.

@ianmoone2359

4 жыл бұрын

Yep, some wiz kid would 3D print it with sintered metal while anyone else was still making the timber moulds & machine the plastic blank, and mixing green sand. That’s why these technologies are dying art forms. It is good to see the knowledge being preserved for posterity. Yes you could cast it or you could have bought a short piece of 6 or 7 inch alluminium round bar stock & just turned it in the lathe & then milled the teeth. I have to say I do enjoy watching this all the same, very satisfying.

Like the ball bearings on the end of a rod to smooth out the sand,I've been using those for nearly 45 yrs when built my first foundry with my late Dad,[burnt a few out since then!] there was no internet then to show you how, I just had B Terry Aspin's book "foundrywork for the amateur" ,having said that I have picked up one or two useful ideas from yourself & others ,never too old to learn, I use mainly petrobond or co2 for plaques with fine letters & mansfield red for anything else,[of course it's not red anymore after 100s of melts!!, thanks for the stovefan castings,[nice castings] Graham.

@myfordboy

5 жыл бұрын

I taught myself from the same book. No internet when i started casting. Terry Aspins son left a comment on here this week.

@headstocktailstock

5 жыл бұрын

Thanks for the reply,didn't know he had a son, his stuffs still relevant today,allthough I have a small propane furnace I still do nearly all my casting using coke & a bouncy castle blower, mainly 'cos we've always got a couple of tons in for the rayburn I like your waste oil burner, will have to make one it's a bit easier than coke Regards Graham.@@myfordboy

How can someone dislike these videos, I'm an experienced machinist and even I learn off this chap. amazing how he edits the videos to keep you watching, quite a feat without any audio dialogue. Thanks bud for sharing.

@user-ps9jh8dk8n

6 жыл бұрын

arif anwari 吗888

@rogerfroud300

6 жыл бұрын

Because in this case it could have been done using a piece of sawn aluminium bar in half the time, that's why.

@tomasfell1453

5 жыл бұрын

Casting is an art and doing good videos too, and theese videos combine both.

I never get tired of watching these videos.

@garretcastlebright8996

7 жыл бұрын

me either.

@tareqahmed3670

7 жыл бұрын

verdatum me too

@robertschumann9059

7 жыл бұрын

verdatum me too

@viannaaltamira1919

7 жыл бұрын

verdatum shotgun gauqe

@Chaos------

7 жыл бұрын

I've learned more in the last year watching youtube videos than I've learned in my entire 12 year span of public education.

Nice accurate casting, not far off true even before you machined it. Like the way you use the chuck to mark the 3 fixing holes. Always seem to pick up something new every time I watch your videos. Thanks again for sharing, your videos are very much appreciated.

There is nothing more rewarding than making things on your own, and it is a please to watch an expert doing it... Thanks for this awesome video!

MY WORD, YOU MAKE THAT LOOK SO EASY.... THANKS TO YOU I CAN FINALLY CAST. MY HAT IS OFF TO YOU.

Great project and I sound like a broken record but innovative techniques and great attention to detail. You never seem to hesitate when going from step A to B to C. Thanks for the videos!

Hats off for you myford, you did your promise about doing a sand casting & you did. Awesome job making that pulley & can't wait to see you build it. I like it & I share it & 2 thumbs up for you. See ya on your next video

This is what I am talking about, engineering parts from scratch! Necessity is the mother of all inventions folks.

@johngiles8121

7 жыл бұрын

Matt Webb !!

@myfordboy, most stepper motors have a fixed number of steps. For example 200 steps per revolution. When you are designing your gear rations you might need to take that into account in your sketch. For example, my hobby CNC router has resolution issues for long moves because the controller wants an integer number of steps per inch and the ratios for the gearing is not an integer. So over the course of about 10 inches the position is wrong by a few 1/1000s. This might not be an issue for what you are doing but if you are going to be using this for gear cutting you need to be able to come back to exactly the same point. Good luck to you, you do some amazing things. -Chris P.S. I switched to alloy rims for my source of aluminum and it makes a huge difference in the quality of my castings thanks for suggesting it.

I Would like to Thankyou for the video it is something i never had the oppurtunity in watching before and i found the process and the outcome fascinating i have a 25 year ol son that lives several states away from me and he and i have had onversations about some od the neat metal videos on KZread that we have seen ubdependitely i was a Wood worker my adult life untill a medical issue caused some paralysis and a traumatic brain injury forcing me a early retirement i do enjoy learning about other trades and skills and because i do have many family members and freinds that are machinists and metal workers ive always been interested in that industry

@myfordboy

5 жыл бұрын

Glad you like the video.

É admirável, uma pessoa das antigas que ama o que faz se adaptando ao novo e moderno, melhorando suas ferramentas usando o que tem em mãos. Parabéns.

Muito bom mesmo valeu grande abraço e mais um inscrito sucesso

Thank you. Excellent use of materials and a great idea. I've seen something like this before but each solution brings something new. Good job!

Как всегда прекрасная работа мастера !!!!! УДАЧИ !!!!!!

@dorindumitrescu7381

5 жыл бұрын

speak human.

It's always a pleasure watch you working! Every time you teach me something new. Thanks for sharing tons of experience.

Who gives unlike for this hard work? Greetings from Serbia

As always, it's a joy to watch you work! Great presentation and simple captions with just enough detail make your videos a cut above the rest.

@kenashley3315

5 жыл бұрын

Playboy

Сижу смотрю и думаю;...и зачем мне это нужно? Ведь я в жизни занимаюсь совсем другим, но досмотрел до конца с большим удовольствием и интересом.))) I sit and watch and think; ... and why do I need it? After all, I am engaged in a completely different life, but I watched it to the end with great pleasure and interest.)))

It's a pleasure watching you work. Thanks for putting this up.

Man...you have this operation down pat! Always a pleasure to see your craftsmanship. 👍

We really enjoy your casting videos! Thanks for sharing your knowledge about this art.

another great job...just getting all my arduino stuff in at the moment to drive a 6inch rotary table as per MEW 249....yet another project to complete along with your myfordboy steam engine LOL.

I never get tired of watching these videos

@erickrosa6881

5 жыл бұрын

i too.

@ilhemedu31

5 жыл бұрын

its relaxing to

Thank you, it is you sharing your skill and information that inspires myself and others to do more and more.

This is called CRAFTSMANSHIP, awesome manufacturing.

Man I want to do this. glad this guy keeps putting out these videos. very educational !

evry thing is prefect i am an old machinist i give you the max stars joseph davides

Genius. This is becoming a lost art but I am impressed. Thank you for sharing.

The old faithfull red screwdriver! love it!

Amazing video, as always, Sir. Thank you. I repeat myself but I wish I had teachers like you.

Hola amigo saludos desde Panamá eres el mejor Dios te bendiga a ti y a tu familia eres de los seres humanos q son especiales en este planeta

I am just geeky enough to have thoroughly enjoyed this video. Thanks for showing.

Good they dont make them like you anymore great video

Your gate tamping tool is superb.

I dont now why but it's Very relaxing watching this

Felicitaciones,no sabia que tambien le gustaba la electrónica del Arduino!gracias por compartir sus videos que tienen muchos trucos y conocimiento. Congratulations, I did not know that I also liked Arduino electronics! Thanks for sharing your videos that have many tricks and knowledge.

Excellent...! Your video inspired me, thanks for sharing, Greetings from Venezuela

Nice video, and by the look of things some very nice upgrades on the way! Thanks for sharing your videos. They are always a joy to watch.

Wow! With skills like this, if you make a mistake it's no problem. Just melt it down and make another one!

Very cool and varied skill-set - man after my own heart. Jack of all trades / Master of a quite a few!

Very cool. Its going to be a very useful setup. And as usual, your work is first class. Thanks for posting.

Thank you for your sharing. Very good sand casting process video, i learnt more from your video.

BRAVO VERY GOOD I'LL NEVER FORGET THIS VIDEO

informative entertaining and educational, as always!

Great video with several interesting and useful techniques. I would love to build the indexer but it just went on the end of a very long list of projects on my workshop ToDo list!

@davidelliott5843

3 жыл бұрын

Check out the ways it can be done with a 48 tooth gear wheel. That number gives a large number of options though the odd numbers are a “bit restricted”.

Dude, you really know what you are doing. Excelent job. Excelent vid, i dont have to skip a frame.

@valdirfransisco170

5 жыл бұрын

Bomsaberqueasobrasem

The Master at work. What a cool project. Thank you!

Excelente, tenho aprendido muito com seus vídeos. São verdadeiras aulas de usinagem e criatividade.

I cannot see how anyone could give Myfordboy's videos a thumbs down!...His videos are awesome!

@sojournsojourntraveler1203

6 жыл бұрын

He went to a great deal more work for the aluminum casting. Never gets into the safety aspects of molten aluminum eater. I cast round stock aluminum and use as needed for different projects. a great cutoff tool is a old finishing wood saw as the fine teeth do not get clogged but they are small enough to not grab too much aluminum.

@aaronjanzen4078

6 жыл бұрын

that's Cause Some People Have Their Ass Above Their Head ,

@sojournsojourntraveler1203

6 жыл бұрын

Back in the day when people worked for a living , when a boss asked about if someone was working or goofing off , one would hope the report was, all I see when I see him is ass and elbows. That meant your bending at the waste and doing something. work.

@Membwayne

5 жыл бұрын

@@aaronjanzen4078 I believe the propper medical term is "recto-cranial inversion"

Learned a lot from this video, thanks for sharing your experience, ..

11:18 a good lesson on where the cutting edge of a drill is and what to sharpen.

Es un trabajo muy hermoso, muy completo y bien realizado, gracias por compartirlo

That was so interesting and informative, a very skilled operation; well done.

The most talented ones don't talk much

Always enjoy watching your videos! Excellent work, attention to detail is and your workmanship is impressive! BTW I grew up in Meopham and Faversham, miss the fish and chips!

Nice project! I always learn from watching your videos. Hopefully there will be follow up videos on this project. Thanks!

100K coming soon Well deserved. Thanks for the video. Backyard furnace workshop is an awesome idea

@myfordboy

7 жыл бұрын

Do I get a badge for 100K?

@cnc-ua

7 жыл бұрын

myfordboy you should!

@antmallett6065

7 жыл бұрын

No, you get a a wall plaque at 300K...

@antmallett6065

7 жыл бұрын

Sorry my bad. Silver award is at 100K.

@myfordboy

7 жыл бұрын

I see that. I did know there was such I thing. I might have to do special video when it arrives.

I like them to, but sometimes they go over my head as to why go through the trouble. It's nice work but the use escapes me r I just don't care. I was just here for the first part the rest just boded me. I liked the cutting of the aluminum bit the teeth an the rest not so much. Thank You Loader. I'm glad you understand it.

Merci beaucoup du partage !!!! Thank you very much for sharing !!!!

Cool video! Thanks for posting

Excellent video. I really enjoyed it. Thank You !

Muito bom

These videos are awesome

You need a molding bench. Your knees will thank you! Nice work.

I like the "machined-in-situ" aspect.

I love your video's, keep up the good work.

Hello Myfordboy Nice work!!! Never made a casting, but now you've got me thinking, ...

Great casting , I enjoyed ! Thanks man ..Thumbs up

Anyone who does lathe work should understand the principle of tool pressure. This person paid no heed to that principle. Otherwise, excellent information and a wonderfully simple video. Thank you for it.

Very cool project. I hope there will be a part 2 where we get to see it in action! Can you go into more detail with the controller, and perhaps post the Arduino sketch?

@myfordboy

7 жыл бұрын

+ More details and the link to the sketch are in the description below the video. You need sketch v2.3

увидел ссылку, спасибо за ваши труды!!!!

Viva England and it's Master Crafters! If only I'd have just had the benefit of witnessing this kind of well-earned competence as a 3rd Grader.. Bodes well for the future because today's young 'uns can see this with a click.One observation (that well may not be correct - but just food for thought) - if you are planning to drive the indexer a long time... (more than two minutes) Those little power components on the Arduino are very precise and accurate and will work perfectly of course as you demonstrate but I suspect maybe not if you try too many repeated operations. I am not an expert but just going by visuals.. For example look at automotive 12 volt ECUs and look how they size the chips in the power section. The Mosfets attached to aluminum heat sinks with heat conducting grease..I Don't know the actual specs just what they look like as far as size. A little beefier to handle the heat would perhaps be better. Hopefully someone who knows will chime in.Very sophisticated work you demonstrate and it is inspiring.

Interesting videos! I just tried to cast a large 10" diameter X 10" tall planter pot out of bronze. I used the Lost Wax and Cavity Pour techniques, filling the inside of the planter with plaster of paris, then inverting the mold to fill the outside of the planter. This was all done in a galvanized 6 gallon bucket. The plaster, filled to the top, was allowed to cure for about 1 month. The wax was then melted out. During the bronze pour there was an incredible amount of boiling, bubbleing, smoking and popping. Almost to the point I where I almost aborted the pour. After de-molding the planter, the results were catostrophic! The planter had massive pock marks, gapping holes and look like it had risen from the ashes of Chernobyl! I wonder if this was caused by the reaction with the plaster, or perhaps the plaster couldn't breathe/out gas properly? Any analysis or recomendations would be awesome! Also, what brand of pouring tongs/shank are you using in Part 64? Thanks for your help!

@myfordboy

5 жыл бұрын

If it is just regular plaster it's going to crack. I have done similar but used a proper investment plaster like this product. www.artisanfoundry.co.uk/product_info.php?products_id=97 If there was the boiling as you describe it was not dry enough. The plaster I mentioned needs probably 5 hours at 650C to dry it out before use.

Very smart! Thank you very much for this video and all the links...

like the video but as a machinist i would recommend using coolant on the lathe, other wise your work hardening your material and your tools.

@Ropetangler

5 жыл бұрын

Whaaaaaat -work hardening Aluminium and high Speed Steel???

Excellent in every way. Thanks for sharing.

Exellent, Very good. From Brazil.

I learned to make sand castings during school metalwork classes. I still have an aluminium version of a Fowler traction engine prancing horse (the originals were brass). The gas fired furnace was incredibly noisy but nobody worried about such details back in the 1970s. I can remember wondering how jabbing the sand down with the ends of sticks could do the job. The metal had to be poured on one continuous flow. No pausing - NONE. It worked very well. My horse looks original.

Nice work. Would I be far wrong if I said it looks very much like you getting ready to cut cam lobes and profiles? The stepper motor indexing the spindexer is exactly how I did it! I used a digital vernier slide for the vertical movements and cut depths.

@myfordboy

7 жыл бұрын

I don't have that use in mind but thanks for the suggestion. I have a little delve into CNC coming soon.

@andrewwilson8317

7 жыл бұрын

myfordboy looking forward to that. Going to be very interesting.

@garthn2561

7 жыл бұрын

CNC varies from very simple to extremely difficult. I CNCed my Myford lathe, can't dream of going back to manual. But that was fairly simple programming (although threading was a bit of a challenge). LinuxCNC or Mach3 are already very capable, but generating Gcode for 3D milling is pretty complex. I was waiting for someone to show a DIY stepper controlled indexer - brilliant.

Great Job myfordboy!!! Thanks for sharing my friend!

i dont have an indexing head. I do have a chinese cnc machine that is great with aluminium.. and a chinese 8x24 lathe I would have used to face the back of the pully then put it on the cnc machine to profile the teeth by drill milling the pattern, then cnc machined the centre hole and outer diameter too. back in the lathe to finish the other face etc. It works, I have made many bicycle chain sprockets.. even in steel (but thats pushing the cnc. 6050). The trouble with the chinese cnc is the cross bars are just only 16mm and 100mm apart. 500mm long and they bend under load. The cutter can twist the rails 1mm with 20kg force. if they had used 20mm shafts that would be about 100kg and a 25mm shaft about 400kg.. I will modify it one day.

@criticallook1352

5 жыл бұрын

+Raymond Merrick The fine China should only be used for special occasions! :

Great stuff,thanx for your time!

love the new gating tool

inspirational work, as always.

Would you please do a match plate style pattern demonstration; the casting shop we use at work operates with that style for efficiency.

@myfordboy

7 жыл бұрын

I don't like the matchplate method. I ram the sand quite hard and like to remove the pattern carefully to avoid damaging the mould.

Surprised at lack of venting, but casting is excellent.

You're good at what you do. My question focuses on the aluminum you poured. How do you determine the aluminum has the proper mixture to hold up to the stress and balance a pulley needs to have?

@myfordboy

4 жыл бұрын

Using metal that has been cast before gives good results.

Lovely build, little confusing though...why not get a disc cut from some supplier and machine that, and for that matter they probably sell one with a tooth for that common belt no?

The wheel came out beautifully, but that's a heck of a lot of sprue.

Excellent work. applause from Mèxico.

Impressive work, that's definitly not your first time you made stuff like that....

Hi MB. Excellent video as always. Are you going to make a video on the construction of the Arduino controller? Would love to see one since I bought all the parts to make one of these a couple of years ago and have still not got round to it. Way too many other things taking priority, like cycling support crew almost every weekend for one of my sons, redecorate front room, new bathroom etc., and reorganise existing workshop to be able to consider doing this kind of project. NOT excuses; reasons haha. Regards Mark in the UK

Thanks for the video. I wish I could come and play with your toys too.

Very good work!

This is educational, thanks

A vocal video would be nice, teaching and explaining