Great video, this really helped me understand this system and trouble shoot it. Thank you
@dennisnolte3497 Жыл бұрын
This video was fantastic, my trim wouldn’t bring my 2000 90 horse mercury 4 stroke boat motor up. I was able to figure the problem out in about 10 minutes after watching this video. Thank you so much for you help..Dennis
@shawnbrinton4198
Жыл бұрын
What was the issue? I've got the same problem.
@dennisnolte3497
Жыл бұрын
@@shawnbrinton4198 it wasn’t the switch, or the next thing in line, it was the third step with the green and blue wires. I checked all the connections on the wire that you said was the one for raising the motor. One connection had a nut behind and on top of the connection. I took the top one off and the connection wire and cleaned them both . The nut closest to the engine needed to be tightened, then I put the wire connection back on and the nut and tightened it snuggly but not too tight.. And praise God my prayers were answered. It worked like brand new. Before it was fixed it would work sometimes and other times wouldn’t work. Then it completely stopped working. Now it works great. In order to understand what I’m talking about you need to watch the video. Before it was walking correctly I switched the two wires green and blue around and tats how I got the motor up for winter storage. That way I knew the hydraulic system was working. Follow those wires directly from the hydraulic system to the engine..thanks for putting that video on and thank you Jesus for leading me to it.
@MrJeepdawg3 жыл бұрын
Straight forward covering all of the components, well done, thanks!
@Carlosboatingadventures200072 жыл бұрын
This actually helped me a lot. Thanks man! I know it was two years ago but this test should be the same for all boats.
@theomcinerney93403 жыл бұрын
Dude that was a great video. Short to the point and covert all bases. Keep up the good work man
@DonVila2 жыл бұрын
This was extremely clear and very helpful. Much appreciated.
@peterbystrom67993 жыл бұрын
Straight forward. Helped me locate my relay problems.
@lucasreuss31703 жыл бұрын
One of the best instinctual videos i have ever seen. Cheers
@ejwmaine2 жыл бұрын
Step No. 1 was it for me! Thank you! Kept me from doing the deep dive!
@theoverbeyhome38863 жыл бұрын
Thanks for the video. If you ever have time, I would like to see a straight forward trim motor bleed and diagnose an actual trim motor / check valve / whatever troubleshooting. Nice job Sir!
@iainmacdonald59074 жыл бұрын
Brilliant, simple training video! Can you take over the Internet! 😁
@michaelloch87993 жыл бұрын
great video... in a few minutes you proved that its a relay... should be an easy fix. Thanks!
@platinumhandymansolutions3 жыл бұрын
Great explantion bro! Thanks!
@BoffaDeezMrBojangles Жыл бұрын
Thank you for your time and help this video was very helpful on my own Tracker I am so lost but have a understanding thank you
@MrCanonballs Жыл бұрын
Thanks for posting. Nice work.
@teamsweeney Жыл бұрын
Excellent explanation. Thank you.
@JC-tt8mp2 жыл бұрын
Best trim video on the web
@terrycurran7806 ай бұрын
Great video, you covered everything
@jamesrahn83393 жыл бұрын
Thanks for this...it's so simple but totally helps when you have no idea..lol. thank you.
@josephd14223 жыл бұрын
I have a twin inboard/outboard mercruser Thank you for the heads up
@robertsilver22113 жыл бұрын
Thanks exactly what I needed...
@douglaswells27393 жыл бұрын
Good vid. My issue on my 100 2+2 1995 model is the down motor actuation sounds normal in sound but my up mechanism sounds screechy rough though works. Fluid is normal level, no milkiness.
@christianblaesbjerg61402 жыл бұрын
Great help. Do I need to order two relays or just the one not working?
@miamielitejetskiyachtrenta52283 жыл бұрын
Excellent video
@lorithomas592211 ай бұрын
Enjoyed the video. Any ideas why tilt goes up and down when out of water but it will not come up when I'm trying to level out in the water
@cepuras Жыл бұрын
Nice video.. kinda surprised about all the spare parts, but I guess it’s a good idea..
@jlix29742 жыл бұрын
Thank you for the video. Everything seems to be testing fine on my boat but I cannot trim up while the motor is running above 2000 rpm. Any ideas of what would cause this?
@jasonkarls23843 жыл бұрын
Very nice video. Thorough discussion on the power source. For the trim unit itself though, what would you do if it is losing hydraulic fluid where the bar moves up and down? Thanks!
@MrLike2surf
Жыл бұрын
I had to replace a seal kit on mine, when that happened.
@danmuller70752 жыл бұрын
Awesome! Thank you!
@theaardee2 жыл бұрын
Thankyou Sir from NZ
@JohnKidd3 жыл бұрын
Need some assistance here, up and down work fine but getting a huge voltage drop even when engine is on and rectifier is out putting 3.1 V. What do you think the issue is?Voltage drop is enough that the actuator stops working
@penstar3 жыл бұрын
Fantastic, easy to understand for amateurs like me, thanks! :)
@johnmacgugan3 жыл бұрын
This is a great video! Thank you very much for the tips. I have a 2018 mercury 115 HP. It goes down just fine, but will not go up. Can’t wait to try this out in the morning and see if it’s actually my relay. Thanks again
@leonlug
3 жыл бұрын
Hi John this is Matt I’m having the same issue with my boat, same year and motor. I was wondering if you were able to fix the issue and how you did it thanks
@johnmacgugan
3 жыл бұрын
@@leonlug yup. Issue resolved. Warranty covered it.
@Tracker18
Жыл бұрын
@@johnmacgugan hey I know is a year ago lol my boat has the same issue. What fixed the problem for you?
@johnmacgugan
Жыл бұрын
There was a recall on the a part in my motor. Fixed for free
@Tracker18
Жыл бұрын
@@johnmacgugan what part did they change?
@tc96z12 жыл бұрын
My 25hp merc 4stroke TRIM WORKS works perfectly GOING UP AND DOWN but I am Not getting any trim signal to the NEW gauge. Confirmed power and ground r good as well as the new trim gauge being the right one I want to add. Any ideas appreciated on whats possible? I have no signal at the motor itself.
@willienicholsjr6513 жыл бұрын
Good evening. I have 1990 4.7 mercuser. outboard will not go down. is there away to test it while its on the boat?
@pistonforge2 жыл бұрын
what about an intermittent problem..i replaced the trim switch and 4 days later the motor came up by himself..last week the motor was try to go down itself..the switch is brand new and work fine for up and down and even on the control the switch is working good..where i should check next?..ty sir for your video
@richburrows3726 Жыл бұрын
Thanks. Help me through my issue which was a loose connection.
@wyoprospector Жыл бұрын
Great demonstration. What if your up does nothing and your down moves outdrive up. Everything was working fine until a metal object hit the up pos relay conection and sparked. Was just a small vent in back of seat.
@mikeremillard2754 жыл бұрын
Are you supposed to grease the zerk on the actuator?
@davidbrearley95467 ай бұрын
Your the man bro
@merlin13463 жыл бұрын
very informative.
@whitetailfreak684 жыл бұрын
Great video, very helpful. Im troubleshooting a 2001 Mercury 150 stroke. It stopped working all together. Wont go up or down by using the engine switch or the shifter switch. My question is where can I find that circuit breaker on the engine? Thanks in advance for your help.
@fatguyoutdoors3511
3 жыл бұрын
Buddy has same problem. What was your final outcome?
@stevetessman58553 жыл бұрын
do the same instructions go for a 3 wire? green, blue, black,
@phuongtran-xw6zs3 жыл бұрын
Thank you .
@truenorthrestorationb4yb25 күн бұрын
Hi I got a 260 mercruiser leg on my 1978 18 donzi I the trim was working now when I trim up for trailering the leg goes down on its own could you suggest a fix or what to test Jim
@favillaverde10 ай бұрын
I have a brand new pontoon, 90 hp mercury, and it won't trim up under way above 2000 rpms. Trims down no issue, trims up and down no issue out of water or parked, trims from either the outboard or the captains chair but still won't trim up under way above 2k rpms. At dealer and they're like it works fine. I'm like yeah it doesn't work when moving on the water. Brand new boat less than 6 hours. Any thoughts?
@flipper247311 ай бұрын
Hello, I have a weird question. On my 2023 Merc 200 hp, with motor off, iff i trim down a bit from a motor level position, after releasing the trim button on motor cowling I hear 3 or 4 ticks. Have you ever heard of such a noise? Thanks so much
@michaelmaciasjr3 жыл бұрын
Thanks man!
@craigp187 Жыл бұрын
I’ve got a buddy who just took his boat for the first time of the year, yesterday. While drifting around, outboard running (2009 MERCURY 115 EFI), his motor died and the trim/tilt stopped working at the same time. I’m thinking a fuse. However, I don’t know which. Thinking the 15 amp HELM fuse. Any ideas? Thanks!
@larryjohnson53082 жыл бұрын
My tilt and trim works up and down fine but when in the water and I give it power my motor pushes down. I have no leaks all seals look good. What might cause this. Thanks
@PJSprinklerRepairStCloud2 жыл бұрын
I have a 2012 pro xs 115 and went out side the other day. The trim had kicked on in the down position and was still trying to go down. I have a switch on the front of the boat and I disconnected. Now the trim won’t go up or down and motor won’t even turn over. Any ideas what I should check?
@anthonywilliams74322 жыл бұрын
So I tested everything and I have voltage where I need it. Connected the motor directly to power and both directions work. As soon as I reconnect the wires and use the switch at the throttle, the up is intermittent. Sometimes I can hear the click and other times nothing. I even connected power to run through the relays and it works great. It gets intermittent when I reconnect the blue connection from the switch. I read somewhere else that if the connection is loose, I could have voltage but not enough current to operate the relay. Does that sound possible? Do the wires from the throttle arm run through the dash or directly back to the motor? I tried tracing wires but with the 9.9 Pro Kicker it is pretty tight in there. I also put my multimeter on the blue wire while connected to see if I still have voltage present and when I press the switch nothing and the motor doesn't trim up. However as soon as I disconnect the wire terminal it has voltage. Any thoughts? I've tried everything.
@OvertheRoadVideos3 жыл бұрын
Great video. My trim down works. Trim up doesn't. Trailer up works. Do you think the issue is trim switch or the relay?
@dylanconwell3630
3 жыл бұрын
I’m having the same exact issue! Find a you’re problem yet?
@rogerrockwell46178 ай бұрын
I've got 2018 75hp. Won't go up or down. Sounds like its that circuit breaker. Problem is I cant find it. The motor worked fine last week. Is it the resetable type.
@thomasgagnon35042 жыл бұрын
Any idea why the throttle trim qorks bur the front and the back switches arent working
@joseignacioapontemedina3303 жыл бұрын
Excelent!!!
@hoapham72103 жыл бұрын
Thank you
@markbolwell30063 жыл бұрын
excellent video . my tilt goes up and not down ,once i swap relays it goes down and not up.seems an obvious relay problem but putting a new relay hasn`t fixed it!
@MrTomtusti
3 жыл бұрын
obviously a bad replacement
@conradforster224
3 жыл бұрын
@@MrTomtusti Not necessarily. The relay that is not being operated is supposed to connect the motor to ground. If this contact in the relay is faulty it will appear as if the good one is bad and the bad one is good. Best bet is to change both.
@justa64falconsprint2 жыл бұрын
great video and thank you. Is this system the same for EFI Mercury's? Mine is built 2017 and it goes up by itself and keeps running until the battery is dead. I think it's my switch of the joystick and not the motor but still need to figure it out. thanks again.
@aaront.1238
2 жыл бұрын
Mine is doing the same. I’m going to load test my batteries to make sure they are not weak. Then I’m going to switch the relays, and see if my problem is just reversed.
@ddogs1015
2 жыл бұрын
@@aaront.1238 I have had the same issue recently on a 2017 merc. what did you find out with your trim issue ?
@ddogs1015
2 жыл бұрын
I have had the same issue recently on a 2017 merc. what did you find out with your trim issue ?
@denispoirier5442 Жыл бұрын
What about that ground cable , if its not grounding properly ?
@tomliddell303 жыл бұрын
So my trim will not stop going down is my switch shot or sticking ?
@shawnbrinton4198 Жыл бұрын
So what if you have 12v coming from the relays when commanded by switch and motor wont trim up, though actuator will trim up when connected directly battery. Im lost.
@JamesAlbritton-cl8ob11 күн бұрын
WhT do you do when the motors working i trimmed it up now it wont come down but the motor is working working
@williamclark56292 жыл бұрын
Good video
@alejandroalbertos213211 ай бұрын
I have a 50hp 2008 2 stroke. It goes up perfectly but when I try to go down it blows the fuse. i will appreciate any help
@Gogdivine3 жыл бұрын
Hi, great video. I'm having a issue with my mercury 1999 50hp 4 stroke power trim that's driving me crazy and nobody iv spoke to knows how to solve it. Any advise would be great. The ram moves up and down perfectly but under load it sinks back to the lowers point. IV tried manually bleeding the system. Iv changed all seals in the ram and ball bearings with the full seal kit. Iv inspected the valve side of the power trim where the reservoir sits and cleaned all parts, everything looks in good order with no wear. in the valve block there is, 1 small ball and spring, 2 larger balls with no spring, 2 cogs and a small drive shaft, all looks good and clean. I am totally baffled, iv done everything people have suggested and the trim still drops under load, you can actually push the ram down with your hand. Any advice would be a God send.
@HavenMelton
Жыл бұрын
Did you figure this out?
@scottfurst4345
Жыл бұрын
@@HavenMelton When changing the oil or repairing the trim it is common to get air in the system. You need to actuate the trim up and down until the bubbles work themselves out. Put the battery on a charger and work that trim until you get full pressure again.
@bruddachuck3 жыл бұрын
Dope!
@poishish13 жыл бұрын
Hey thanks for this tutorial this is perfect ! I followed the trouble shooting. I found that the voltage is perfect all long. I opened the top of the trim motor to check the voltage inside and it was ok too. But the inside of the trim motor is full of dirt. The problème is that the sometime the motor works and sometime not. I guess there is something inside the trim motor maybe the brush ? Do you have a video to clean the inside of the motor ?
@garester94501
3 жыл бұрын
did you ever get an answer or fix the problem? I have a similar problem
@poishish1
3 жыл бұрын
@@garester94501 yes i fixed it, I unmounted the trim motor, I took appart the motor in pieces, sanded and clean the part. It was completely corroded. And now everything is working perfect !
@garester94501
3 жыл бұрын
@@poishish1 what was the part that was corroded? Was it the piston? Ram? Hydraulic cylinder? Did you have to replace any seals or other parts?
@poishish1
3 жыл бұрын
@@garester94501 inside the electric motor the rest was ok
@poishish1
3 жыл бұрын
I had to replace nothing. Just cleaning Ann’s sanding paper
@richardpippin61592 жыл бұрын
What does it mean when it only goes up about half way?
@hmongxwb883 күн бұрын
Hmmmm i dont think my evinrude dont have a circuit breaker but it does work if i supply 12v directly to the wire but switch wont do nothing so Gotta check my switch thanks!!!
@bouldernelsonbigfoot Жыл бұрын
Awesome
@numismaticausa2628 Жыл бұрын
🔔🔔🔔🔔Buen vídeo excelente gracias 🔔🔔🔔🔔🔔
@TROKERO5593 жыл бұрын
What if I replaced both fuses and it clicked but it won't go up or down
@hikermansteve3 жыл бұрын
Excellent presentation. My boat is garage kept. Last night the power trim raised itself. I lowered the motor with the trim switch on the throttle. When I woke up this morning i found the motor had raised again and wedged the boat in my garage. I attempted to lower the motor from the throttle control and all I heard was a click in up or down position. Is this a switch problem?
@paulrodriguez5348
2 жыл бұрын
Your boat is haunted
@Greg-dp6ht
2 жыл бұрын
I had the same thing happen to me. I was watching as the trim suddenly started going up on its own. Checked and all the trim switches were in the correct positions at the time. I replaced the relays and we'll see if that fixes it. Your boat is NOT haunted. Good thing my friend was also there at the time as a witness or no one would believe this
@MselHD103
2 жыл бұрын
@@Greg-dp6ht having the same problem ..was it the relays?
@michaelchapman4261
Жыл бұрын
Was the relays the problem?
@bluskytoo
Ай бұрын
someone wants to go boating !
@MrMedicAdnan8 ай бұрын
excelent
@markcarpenter76822 жыл бұрын
What if trim works up and down gets sluggish and stops working then starts working when not used for a few minutes? Changed relays 2x does same thing when using switch on engine and throttle handle.
@Tracker18
Жыл бұрын
Hey did you fixed the problem?
@gregorycarter56916 ай бұрын
Mine just clicks when I press up or down? I replaced the solenoids. Still just clicks
@BoffaDeezMrBojangles Жыл бұрын
Hello if anyone can help me ?? Where is this circuit breaker on my Mercury 2 stroke outboard 60HP I am frustrated any help be appreciated thank you
@Utuber1977 Жыл бұрын
I have a brand new 150 merc was out today about to plane and noticed the motor started to trim up and wouldn’t stop. I had to switch motor off and I couldn’t stop it even after resetting. Only way to get motor down was to flip the green and blue cables to get me back to trailer. Any ideas?
@geostrong3606
Ай бұрын
I have the same problem so what u do sir
@MatanuskaHIGH3 жыл бұрын
I have a tracker targa with a 150 mercury and the trim only works when going 2000 rpms or lower. Once I get above that it won’t work. Trying to trim while on plane won’t work. So I can’t lift the nose when there are waves etc or be more efficient on plane. Anyone know what could cause this? All trim works great when not moving or moving slow at 2000 rpms but if I don’t have it trimmed down I can’t go full throttle it Boggs down and if I’m above 2000 rpms I can’t trim at all.
@jlix2974
2 жыл бұрын
I have the same issue on my boat. I can trim down at any rpm but I can only trim up at 2000 rpm. Did you find a fix for this?
@chadfeldotte49837 ай бұрын
Lost my up trim, down still worked. Replaced both relays and same problem. I flipped the blue/green wire and the down switch made it come up. Where does my problem lay. Bad switch? Neither switch will make it come up.
@grantdegi
4 ай бұрын
I have the same problem did you figure this out?
@chadfeldotte4983
4 ай бұрын
Trim sensor
@geraldjohnson23622 жыл бұрын
Something you did not cover , my power trim works as it should until you are going down the lake , it will not trim up going down the lake , it looks like it is jumping , if it is trimmed up and you take off it goes down .
@tompalicke20773 жыл бұрын
My problem is the motor trims up and i cannot stop it. Does this whenever it feels like....
@abrahamlaguna3866
2 жыл бұрын
Same problem did you ever find the problem?
@k.tanaka1866 Жыл бұрын
what can cause the outboard to trim up by itself (and not stop?)
@tiffbiggs5506
Жыл бұрын
Figure it out? Having same problem
@k.tanaka1866
Жыл бұрын
@@tiffbiggs5506 it was the faulty trim switch on the outboard. Cost me 40 bucks in Amazon. I noticed that when I disconnected the switch the power trim was acting normal
@user-jj9ix9is7y Жыл бұрын
Mine is when battery connected trim hung on running without key on
@williamadams22143 жыл бұрын
My tilt and trim works up and down but only for a few seconds. Then it quits and you can wait a few minutes and it will work again. replaced the two relays same thing. what can i check?
@markcarpenter7682
2 жыл бұрын
I got same issues you ever figure it out?
@garymcpherson616
2 жыл бұрын
I would replace the circuit breaker
@JamesAlbritton-cl8ob11 күн бұрын
It went up but not down but its working full of oil
@moose-sb3ce3 жыл бұрын
Great video! still need your advice; my merc 60 hp outboard will randomly raise up and won't go down. The trim engine also seemed to be stuck and would not turn off till I disconnected at the relay switch. To fix the immediate problem, I switched the blue and green wires to the relays to allow the motor go down so I could get back to the dock. Later, I replaced the two relays-but the problem persists! Can you help me figure out what I am missing?
@carloso.burattini5075
3 жыл бұрын
I have the same exact problem, my merc 300 inboard outboard on my 2017 Monterey 264 FS randomly raises up and won't go down. Please share how you fixed it
@abrahamlaguna3866
2 жыл бұрын
Same issue did you guys ever find the problem?
@andysangels19709 ай бұрын
My trim isn’t working at all. I get no power I just replaced 2 solenoids
@wesleyharding75443 жыл бұрын
What if it clicks but does nothing.?
@a13wattlightbulb
3 жыл бұрын
Same issue here....
@joewoodard9215
3 жыл бұрын
Same issue here just clicks
@PA96704
Жыл бұрын
Relays
@brunoortiz1049
23 күн бұрын
Was it the relays??
@brunoortiz1049
23 күн бұрын
@@joewoodard9215was it the relay’s?
@beaniril887010 ай бұрын
If actuator motor is good, why not just connect green and blue wire to an on/off/on switch and forget about the relay?
@joedaley97013 жыл бұрын
trim tilt up stops part way up then stops can't continue until waiting about 30 seconds then can continue same happens going down. can anyone help?
@MrTomtusti
3 жыл бұрын
low on fluid
@07Convertable2 жыл бұрын
What happens if neither up or down are working from either the shifter or the stern controller?
@Martinxeneize10
2 жыл бұрын
Did you figure out the issue? Im having the same problem.
@07Convertable
2 жыл бұрын
@Martin Rozados I have not gotten back around to it since winter set in. Now that it is lighter later into the day, I'm planning on resuming the task after work. Stay tuned.
@Martinxeneize10
2 жыл бұрын
@@07Convertable aye good luck. I changed both relays that didnt fix it. My trim motor works. Switches do aswell. So must be some faulty wire somewhere
@07Convertable
2 жыл бұрын
@@Martinxeneize10 My trim motor works when I jumper it directly from the battery so I know that the motor and pump are good. I have to trim buttons, one on the shifter and one on the stern of the boat next to the ladder. I feel that the problem is somewhere down the line where both trim controls meet since neither are working. I will get to it soon because it is warming up quickly!
@Martinxeneize10
2 жыл бұрын
@@07Convertable man i have the same issue. I might re crimp that whole section at this point because it doesnt look so good anyways. Ill let u know what the issue was when i solve it
@1365andy3 жыл бұрын
I GOT A ? i have 1995 mariner 60 hp and it's going up on it's own first time it almost burned up there was a small fire have you heard of this ?
@abrahamlaguna3866
2 жыл бұрын
I have same issue did you ever find the problem?
@abrahamlaguna3866
2 жыл бұрын
@GeorgeClay
@1365andy
2 жыл бұрын
i think it's the trim switch on gear lever i had to replace all the others they burned up I heard it happened to a brand new mercury 250 i just put a switch on battery so i can turn it off
@keithhumfleet5458Ай бұрын
Bad ground
@runbmc358 ай бұрын
R un crystal Michigan
@chrisvanzandt54005 ай бұрын
Your camera man is terrible
@probeach16953 жыл бұрын
Great lesson Warm greetings from Bobcaygeon Ontario Canada lock 32
Пікірлер: 157
Great video, this really helped me understand this system and trouble shoot it. Thank you
This video was fantastic, my trim wouldn’t bring my 2000 90 horse mercury 4 stroke boat motor up. I was able to figure the problem out in about 10 minutes after watching this video. Thank you so much for you help..Dennis
@shawnbrinton4198
Жыл бұрын
What was the issue? I've got the same problem.
@dennisnolte3497
Жыл бұрын
@@shawnbrinton4198 it wasn’t the switch, or the next thing in line, it was the third step with the green and blue wires. I checked all the connections on the wire that you said was the one for raising the motor. One connection had a nut behind and on top of the connection. I took the top one off and the connection wire and cleaned them both . The nut closest to the engine needed to be tightened, then I put the wire connection back on and the nut and tightened it snuggly but not too tight.. And praise God my prayers were answered. It worked like brand new. Before it was fixed it would work sometimes and other times wouldn’t work. Then it completely stopped working. Now it works great. In order to understand what I’m talking about you need to watch the video. Before it was walking correctly I switched the two wires green and blue around and tats how I got the motor up for winter storage. That way I knew the hydraulic system was working. Follow those wires directly from the hydraulic system to the engine..thanks for putting that video on and thank you Jesus for leading me to it.
Straight forward covering all of the components, well done, thanks!
This actually helped me a lot. Thanks man! I know it was two years ago but this test should be the same for all boats.
Dude that was a great video. Short to the point and covert all bases. Keep up the good work man
This was extremely clear and very helpful. Much appreciated.
Straight forward. Helped me locate my relay problems.
One of the best instinctual videos i have ever seen. Cheers
Step No. 1 was it for me! Thank you! Kept me from doing the deep dive!
Thanks for the video. If you ever have time, I would like to see a straight forward trim motor bleed and diagnose an actual trim motor / check valve / whatever troubleshooting. Nice job Sir!
Brilliant, simple training video! Can you take over the Internet! 😁
great video... in a few minutes you proved that its a relay... should be an easy fix. Thanks!
Great explantion bro! Thanks!
Thank you for your time and help this video was very helpful on my own Tracker I am so lost but have a understanding thank you
Thanks for posting. Nice work.
Excellent explanation. Thank you.
Best trim video on the web
Great video, you covered everything
Thanks for this...it's so simple but totally helps when you have no idea..lol. thank you.
I have a twin inboard/outboard mercruser Thank you for the heads up
Thanks exactly what I needed...
Good vid. My issue on my 100 2+2 1995 model is the down motor actuation sounds normal in sound but my up mechanism sounds screechy rough though works. Fluid is normal level, no milkiness.
Great help. Do I need to order two relays or just the one not working?
Excellent video
Enjoyed the video. Any ideas why tilt goes up and down when out of water but it will not come up when I'm trying to level out in the water
Nice video.. kinda surprised about all the spare parts, but I guess it’s a good idea..
Thank you for the video. Everything seems to be testing fine on my boat but I cannot trim up while the motor is running above 2000 rpm. Any ideas of what would cause this?
Very nice video. Thorough discussion on the power source. For the trim unit itself though, what would you do if it is losing hydraulic fluid where the bar moves up and down? Thanks!
@MrLike2surf
Жыл бұрын
I had to replace a seal kit on mine, when that happened.
Awesome! Thank you!
Thankyou Sir from NZ
Need some assistance here, up and down work fine but getting a huge voltage drop even when engine is on and rectifier is out putting 3.1 V. What do you think the issue is?Voltage drop is enough that the actuator stops working
Fantastic, easy to understand for amateurs like me, thanks! :)
This is a great video! Thank you very much for the tips. I have a 2018 mercury 115 HP. It goes down just fine, but will not go up. Can’t wait to try this out in the morning and see if it’s actually my relay. Thanks again
@leonlug
3 жыл бұрын
Hi John this is Matt I’m having the same issue with my boat, same year and motor. I was wondering if you were able to fix the issue and how you did it thanks
@johnmacgugan
3 жыл бұрын
@@leonlug yup. Issue resolved. Warranty covered it.
@Tracker18
Жыл бұрын
@@johnmacgugan hey I know is a year ago lol my boat has the same issue. What fixed the problem for you?
@johnmacgugan
Жыл бұрын
There was a recall on the a part in my motor. Fixed for free
@Tracker18
Жыл бұрын
@@johnmacgugan what part did they change?
My 25hp merc 4stroke TRIM WORKS works perfectly GOING UP AND DOWN but I am Not getting any trim signal to the NEW gauge. Confirmed power and ground r good as well as the new trim gauge being the right one I want to add. Any ideas appreciated on whats possible? I have no signal at the motor itself.
Good evening. I have 1990 4.7 mercuser. outboard will not go down. is there away to test it while its on the boat?
what about an intermittent problem..i replaced the trim switch and 4 days later the motor came up by himself..last week the motor was try to go down itself..the switch is brand new and work fine for up and down and even on the control the switch is working good..where i should check next?..ty sir for your video
Thanks. Help me through my issue which was a loose connection.
Great demonstration. What if your up does nothing and your down moves outdrive up. Everything was working fine until a metal object hit the up pos relay conection and sparked. Was just a small vent in back of seat.
Are you supposed to grease the zerk on the actuator?
Your the man bro
very informative.
Great video, very helpful. Im troubleshooting a 2001 Mercury 150 stroke. It stopped working all together. Wont go up or down by using the engine switch or the shifter switch. My question is where can I find that circuit breaker on the engine? Thanks in advance for your help.
@fatguyoutdoors3511
3 жыл бұрын
Buddy has same problem. What was your final outcome?
do the same instructions go for a 3 wire? green, blue, black,
Thank you .
Hi I got a 260 mercruiser leg on my 1978 18 donzi I the trim was working now when I trim up for trailering the leg goes down on its own could you suggest a fix or what to test Jim
I have a brand new pontoon, 90 hp mercury, and it won't trim up under way above 2000 rpms. Trims down no issue, trims up and down no issue out of water or parked, trims from either the outboard or the captains chair but still won't trim up under way above 2k rpms. At dealer and they're like it works fine. I'm like yeah it doesn't work when moving on the water. Brand new boat less than 6 hours. Any thoughts?
Hello, I have a weird question. On my 2023 Merc 200 hp, with motor off, iff i trim down a bit from a motor level position, after releasing the trim button on motor cowling I hear 3 or 4 ticks. Have you ever heard of such a noise? Thanks so much
Thanks man!
I’ve got a buddy who just took his boat for the first time of the year, yesterday. While drifting around, outboard running (2009 MERCURY 115 EFI), his motor died and the trim/tilt stopped working at the same time. I’m thinking a fuse. However, I don’t know which. Thinking the 15 amp HELM fuse. Any ideas? Thanks!
My tilt and trim works up and down fine but when in the water and I give it power my motor pushes down. I have no leaks all seals look good. What might cause this. Thanks
I have a 2012 pro xs 115 and went out side the other day. The trim had kicked on in the down position and was still trying to go down. I have a switch on the front of the boat and I disconnected. Now the trim won’t go up or down and motor won’t even turn over. Any ideas what I should check?
So I tested everything and I have voltage where I need it. Connected the motor directly to power and both directions work. As soon as I reconnect the wires and use the switch at the throttle, the up is intermittent. Sometimes I can hear the click and other times nothing. I even connected power to run through the relays and it works great. It gets intermittent when I reconnect the blue connection from the switch. I read somewhere else that if the connection is loose, I could have voltage but not enough current to operate the relay. Does that sound possible? Do the wires from the throttle arm run through the dash or directly back to the motor? I tried tracing wires but with the 9.9 Pro Kicker it is pretty tight in there. I also put my multimeter on the blue wire while connected to see if I still have voltage present and when I press the switch nothing and the motor doesn't trim up. However as soon as I disconnect the wire terminal it has voltage. Any thoughts? I've tried everything.
Great video. My trim down works. Trim up doesn't. Trailer up works. Do you think the issue is trim switch or the relay?
@dylanconwell3630
3 жыл бұрын
I’m having the same exact issue! Find a you’re problem yet?
I've got 2018 75hp. Won't go up or down. Sounds like its that circuit breaker. Problem is I cant find it. The motor worked fine last week. Is it the resetable type.
Any idea why the throttle trim qorks bur the front and the back switches arent working
Excelent!!!
Thank you
excellent video . my tilt goes up and not down ,once i swap relays it goes down and not up.seems an obvious relay problem but putting a new relay hasn`t fixed it!
@MrTomtusti
3 жыл бұрын
obviously a bad replacement
@conradforster224
3 жыл бұрын
@@MrTomtusti Not necessarily. The relay that is not being operated is supposed to connect the motor to ground. If this contact in the relay is faulty it will appear as if the good one is bad and the bad one is good. Best bet is to change both.
great video and thank you. Is this system the same for EFI Mercury's? Mine is built 2017 and it goes up by itself and keeps running until the battery is dead. I think it's my switch of the joystick and not the motor but still need to figure it out. thanks again.
@aaront.1238
2 жыл бұрын
Mine is doing the same. I’m going to load test my batteries to make sure they are not weak. Then I’m going to switch the relays, and see if my problem is just reversed.
@ddogs1015
2 жыл бұрын
@@aaront.1238 I have had the same issue recently on a 2017 merc. what did you find out with your trim issue ?
@ddogs1015
2 жыл бұрын
I have had the same issue recently on a 2017 merc. what did you find out with your trim issue ?
What about that ground cable , if its not grounding properly ?
So my trim will not stop going down is my switch shot or sticking ?
So what if you have 12v coming from the relays when commanded by switch and motor wont trim up, though actuator will trim up when connected directly battery. Im lost.
WhT do you do when the motors working i trimmed it up now it wont come down but the motor is working working
Good video
I have a 50hp 2008 2 stroke. It goes up perfectly but when I try to go down it blows the fuse. i will appreciate any help
Hi, great video. I'm having a issue with my mercury 1999 50hp 4 stroke power trim that's driving me crazy and nobody iv spoke to knows how to solve it. Any advise would be great. The ram moves up and down perfectly but under load it sinks back to the lowers point. IV tried manually bleeding the system. Iv changed all seals in the ram and ball bearings with the full seal kit. Iv inspected the valve side of the power trim where the reservoir sits and cleaned all parts, everything looks in good order with no wear. in the valve block there is, 1 small ball and spring, 2 larger balls with no spring, 2 cogs and a small drive shaft, all looks good and clean. I am totally baffled, iv done everything people have suggested and the trim still drops under load, you can actually push the ram down with your hand. Any advice would be a God send.
@HavenMelton
Жыл бұрын
Did you figure this out?
@scottfurst4345
Жыл бұрын
@@HavenMelton When changing the oil or repairing the trim it is common to get air in the system. You need to actuate the trim up and down until the bubbles work themselves out. Put the battery on a charger and work that trim until you get full pressure again.
Dope!
Hey thanks for this tutorial this is perfect ! I followed the trouble shooting. I found that the voltage is perfect all long. I opened the top of the trim motor to check the voltage inside and it was ok too. But the inside of the trim motor is full of dirt. The problème is that the sometime the motor works and sometime not. I guess there is something inside the trim motor maybe the brush ? Do you have a video to clean the inside of the motor ?
@garester94501
3 жыл бұрын
did you ever get an answer or fix the problem? I have a similar problem
@poishish1
3 жыл бұрын
@@garester94501 yes i fixed it, I unmounted the trim motor, I took appart the motor in pieces, sanded and clean the part. It was completely corroded. And now everything is working perfect !
@garester94501
3 жыл бұрын
@@poishish1 what was the part that was corroded? Was it the piston? Ram? Hydraulic cylinder? Did you have to replace any seals or other parts?
@poishish1
3 жыл бұрын
@@garester94501 inside the electric motor the rest was ok
@poishish1
3 жыл бұрын
I had to replace nothing. Just cleaning Ann’s sanding paper
What does it mean when it only goes up about half way?
Hmmmm i dont think my evinrude dont have a circuit breaker but it does work if i supply 12v directly to the wire but switch wont do nothing so Gotta check my switch thanks!!!
Awesome
🔔🔔🔔🔔Buen vídeo excelente gracias 🔔🔔🔔🔔🔔
What if I replaced both fuses and it clicked but it won't go up or down
Excellent presentation. My boat is garage kept. Last night the power trim raised itself. I lowered the motor with the trim switch on the throttle. When I woke up this morning i found the motor had raised again and wedged the boat in my garage. I attempted to lower the motor from the throttle control and all I heard was a click in up or down position. Is this a switch problem?
@paulrodriguez5348
2 жыл бұрын
Your boat is haunted
@Greg-dp6ht
2 жыл бұрын
I had the same thing happen to me. I was watching as the trim suddenly started going up on its own. Checked and all the trim switches were in the correct positions at the time. I replaced the relays and we'll see if that fixes it. Your boat is NOT haunted. Good thing my friend was also there at the time as a witness or no one would believe this
@MselHD103
2 жыл бұрын
@@Greg-dp6ht having the same problem ..was it the relays?
@michaelchapman4261
Жыл бұрын
Was the relays the problem?
@bluskytoo
Ай бұрын
someone wants to go boating !
excelent
What if trim works up and down gets sluggish and stops working then starts working when not used for a few minutes? Changed relays 2x does same thing when using switch on engine and throttle handle.
@Tracker18
Жыл бұрын
Hey did you fixed the problem?
Mine just clicks when I press up or down? I replaced the solenoids. Still just clicks
Hello if anyone can help me ?? Where is this circuit breaker on my Mercury 2 stroke outboard 60HP I am frustrated any help be appreciated thank you
I have a brand new 150 merc was out today about to plane and noticed the motor started to trim up and wouldn’t stop. I had to switch motor off and I couldn’t stop it even after resetting. Only way to get motor down was to flip the green and blue cables to get me back to trailer. Any ideas?
@geostrong3606
Ай бұрын
I have the same problem so what u do sir
I have a tracker targa with a 150 mercury and the trim only works when going 2000 rpms or lower. Once I get above that it won’t work. Trying to trim while on plane won’t work. So I can’t lift the nose when there are waves etc or be more efficient on plane. Anyone know what could cause this? All trim works great when not moving or moving slow at 2000 rpms but if I don’t have it trimmed down I can’t go full throttle it Boggs down and if I’m above 2000 rpms I can’t trim at all.
@jlix2974
2 жыл бұрын
I have the same issue on my boat. I can trim down at any rpm but I can only trim up at 2000 rpm. Did you find a fix for this?
Lost my up trim, down still worked. Replaced both relays and same problem. I flipped the blue/green wire and the down switch made it come up. Where does my problem lay. Bad switch? Neither switch will make it come up.
@grantdegi
4 ай бұрын
I have the same problem did you figure this out?
@chadfeldotte4983
4 ай бұрын
Trim sensor
Something you did not cover , my power trim works as it should until you are going down the lake , it will not trim up going down the lake , it looks like it is jumping , if it is trimmed up and you take off it goes down .
My problem is the motor trims up and i cannot stop it. Does this whenever it feels like....
@abrahamlaguna3866
2 жыл бұрын
Same problem did you ever find the problem?
what can cause the outboard to trim up by itself (and not stop?)
@tiffbiggs5506
Жыл бұрын
Figure it out? Having same problem
@k.tanaka1866
Жыл бұрын
@@tiffbiggs5506 it was the faulty trim switch on the outboard. Cost me 40 bucks in Amazon. I noticed that when I disconnected the switch the power trim was acting normal
Mine is when battery connected trim hung on running without key on
My tilt and trim works up and down but only for a few seconds. Then it quits and you can wait a few minutes and it will work again. replaced the two relays same thing. what can i check?
@markcarpenter7682
2 жыл бұрын
I got same issues you ever figure it out?
@garymcpherson616
2 жыл бұрын
I would replace the circuit breaker
It went up but not down but its working full of oil
Great video! still need your advice; my merc 60 hp outboard will randomly raise up and won't go down. The trim engine also seemed to be stuck and would not turn off till I disconnected at the relay switch. To fix the immediate problem, I switched the blue and green wires to the relays to allow the motor go down so I could get back to the dock. Later, I replaced the two relays-but the problem persists! Can you help me figure out what I am missing?
@carloso.burattini5075
3 жыл бұрын
I have the same exact problem, my merc 300 inboard outboard on my 2017 Monterey 264 FS randomly raises up and won't go down. Please share how you fixed it
@abrahamlaguna3866
2 жыл бұрын
Same issue did you guys ever find the problem?
My trim isn’t working at all. I get no power I just replaced 2 solenoids
What if it clicks but does nothing.?
@a13wattlightbulb
3 жыл бұрын
Same issue here....
@joewoodard9215
3 жыл бұрын
Same issue here just clicks
@PA96704
Жыл бұрын
Relays
@brunoortiz1049
23 күн бұрын
Was it the relays??
@brunoortiz1049
23 күн бұрын
@@joewoodard9215was it the relay’s?
If actuator motor is good, why not just connect green and blue wire to an on/off/on switch and forget about the relay?
trim tilt up stops part way up then stops can't continue until waiting about 30 seconds then can continue same happens going down. can anyone help?
@MrTomtusti
3 жыл бұрын
low on fluid
What happens if neither up or down are working from either the shifter or the stern controller?
@Martinxeneize10
2 жыл бұрын
Did you figure out the issue? Im having the same problem.
@07Convertable
2 жыл бұрын
@Martin Rozados I have not gotten back around to it since winter set in. Now that it is lighter later into the day, I'm planning on resuming the task after work. Stay tuned.
@Martinxeneize10
2 жыл бұрын
@@07Convertable aye good luck. I changed both relays that didnt fix it. My trim motor works. Switches do aswell. So must be some faulty wire somewhere
@07Convertable
2 жыл бұрын
@@Martinxeneize10 My trim motor works when I jumper it directly from the battery so I know that the motor and pump are good. I have to trim buttons, one on the shifter and one on the stern of the boat next to the ladder. I feel that the problem is somewhere down the line where both trim controls meet since neither are working. I will get to it soon because it is warming up quickly!
@Martinxeneize10
2 жыл бұрын
@@07Convertable man i have the same issue. I might re crimp that whole section at this point because it doesnt look so good anyways. Ill let u know what the issue was when i solve it
I GOT A ? i have 1995 mariner 60 hp and it's going up on it's own first time it almost burned up there was a small fire have you heard of this ?
@abrahamlaguna3866
2 жыл бұрын
I have same issue did you ever find the problem?
@abrahamlaguna3866
2 жыл бұрын
@GeorgeClay
@1365andy
2 жыл бұрын
i think it's the trim switch on gear lever i had to replace all the others they burned up I heard it happened to a brand new mercury 250 i just put a switch on battery so i can turn it off
Bad ground
R un crystal Michigan
Your camera man is terrible
Great lesson Warm greetings from Bobcaygeon Ontario Canada lock 32