⛐ Check out our Garage to see what tools we use and recommend: www.amazon.com/shop/worldmechanics ⛐ Subscribe and hit the notification bell by the subscribe button for new videos: kzread.info ⛐ Our GoFundme Page: www.gofundme.com/auto-repair-guys

@rcaddictive8572

3 жыл бұрын

Question i checked everything else changed the relay u replaced and it still won't turn over??

@scotttaberner9124

Жыл бұрын

@@rcaddictive8572 maybe it is the crank shaft position sensor

Para las personas que tengas problemas con que les parte se les para en un rato y tira gases por el escape detonaciones no acelera el carro o acelera y solo llega 3 rpm cambien el Sensor de presión de combustible es una chingada ese sensor no da falla en si en algunas oportunidades en el escáner

So when you pulled out the fuse for fuel injector, I just realized that is the fuse that is missing in my friend’s car,that I explained in my first comment. Why the car runs with the injector fuse missing?

Love your channel but 3 things can cause a no start. No fuel, no spark, and also the 3rd is bad ignition timing.

@jordan23fann

Жыл бұрын

And how do you fix that

@rixbaker

3 күн бұрын

Compression, including valve timing.

This just saved me a trip to the repair shop. Thanks!

@rcaddictive8572

3 жыл бұрын

@keith staples did u replace the relay?

@FokwaDivine

2 жыл бұрын

What did you do to fix bro ?

Gonna have to try this because the people said “its a head gasket u need a new engine” but seems like bs. It cranks but wont start

Thanks for the video, it's helpful

My Mazda Tribute, 2003, 4 cylinder, has a problem of cutting off and stop while driving. This happens almost at any speed but almost sure to happen when you slow down. We tried to change the fuel pump, spark plugs, engine oil, oil filter, air filter and some relays but the problem did not go away! What could be the problem? Please help! I live in a remote part of Zambia and have no easy access to good garages and mostly it's guess work we do in order to try and fix the problem! Any suggestions please!

What if it's a smart key ignition

Really great video ,,,,shearing this video thanks for you ...

Thank you, this. Is,, very helpful

you saved me 700$ thank you!

Thank you

I replaced my harmonic balancer without finding top dead center first. 😅😅😢 is it possible to get the timing on my motor back correct without having to open up the whole motor?

it is helping thank you.

very helpful👍👍👍👍👍Thanks

Do this also pertain to push start ?

Thanks for this video

My 3 cranks but sometimes won’t start then eventually starts Intermittent problem Any thoughts

Very good Sir

Great video. Thank you.

Thank you sooooo much for this video. !!!

Perfect. can i call your Dr.Mazda? anyway...good job.

Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem?

what kina battery does Mazda 2 sports 2014 take ??

Please up videos from land rover lr2 I not fine any video for thi vehicle thansk goog job man

the in tank works but the second one on motor wont even replaced any ideas?

Hmm... I will try a new relay, however with my Mazda 6 I think I need a new throttle body When I force the "butterfly" open the car will start, but run weird because it can not auto adjust when it is stuck in one position...

@ztwntyn8

Жыл бұрын

Yeah, I’d say the motor in the throttle body actuator went bad. Can’t you get just the actuator? Or it’s the pcm not controlling it anymore.. bad circuit

@ztwntyn8

Жыл бұрын

Or the gas pedal which sends the signal could be faulty and of course wiring should be looked at just to make sure

Excellent video I learnt alot

Nice vidéo but I am a bit confused. Why did you replace the fuel injector relay given that fuel pump was working ?

@mangozxd

2 жыл бұрын

There’s two fuel injectors he said

My mazda starts okay but after driving it don't want to start what could be

My Mazda cx-7 failure to start but when depress gas pedal it start what's the problem

Hello, I'm looking to buy Cx7 or Cx9 mazda between 2008-2010 model. I did some research and looks like mazda suv is quite a headache and problematic. Any recommendations? Thanks in advance.

@bigwahoo8686

4 ай бұрын

Chevy Tahoe.

I performed DPF regeneration on Mazda C3. After the regeneration completed the car wasn't able to start. Please help..

First of all, thanks for the video. Secondly,my friend’s 2011 Mazda CX-7,why are the two light blue relays missing and the two rows of fusible links,next to the relays,on second row,missing a fuse also? But your car has all the fuses,not one missing. Is it not needed ? Thanks

@wyattflp6163

4 ай бұрын

Same car here, they are not used in this particular model/year, L4

My mazda 3 2007 coil pack keeps burning what is the problem

Hei man hw a u I have a problem with my car demio 2005 engine to mush shaking

jose torres so when it happens could be somwthig whith the fuel pump and fuse amd relays

@hingo078

3 жыл бұрын

Chrisfix has the answer to your question

What about 2005 ford territory same problem

Did anyone ever think to check the OBD?

I have 03 Protege 2.0 that cranks but no start I’m unable to communicate with the computer with my scan tool I’ve also tried a different computer and got the same thing hope you can give me an idea of what I can check? Thanks

@michaelwhilden8543

4 жыл бұрын

Need a new ecu

Need your help

My Mazda 5, built in 2001, was driving normally and suddenly it stopped gasping. I had to stop and wanted to restart the car but the only noises came out like in the video. I read the error code P0341 with the OBD reader and it stands for camshaft position sensor. I swapped that out too but still nothing. does anyone have any ideas.

@spencerharmon1084

7 ай бұрын

Jumped timing?

I would like a comment or an idea about what could possibly be wrong when the car (Mazda CX7) starts ie. fires on all four but then immediately cuts out. There was nothing wrong when last used and then this. I have checked the fuses but I don't have a spare relay to swap for one of the others so there it stops.

@onewhoknowsrevenge6807

Жыл бұрын

The problem is its a Mazda--make good micro waves when they junked.

Awesome work. I need some help with my 2011 Mazda (6) Atenza. While driving the car it was shut down with just the ignition lights remaining. I tried to restart the car but it only cranks. After several checks we found out there is no gas feeding into the engine and no sparks from the coil packs either. We changer 3 crank sensors as it was thought to be the problem, but after the 3rd change we decided to looking the issue deeper. We got the car system scanned but nothing was detected except for a code P0661 which was sometging about the manifold sensor. We checked all fuses inside the car and under the hood. All fuses were ok, but we never checked the relays. Can a bad relay make the brain not tell the system to inject the fuel and fire the sparks? There is no sparks from none of the coil packs and the test from the crank sensor connector showed that cables are ok. I even got the computer reprogrammed to see if it was change the status as there is a red flashing 'lock and car' icon in my dash, which someone said the car may have shut down because of this. Any help? No one seem to be able to rectify the problem

@therealboss14gaming87

3 жыл бұрын

Did you ever fix it

@cedanecox5733

3 жыл бұрын

@@therealboss14gaming87 yes! It was the crank sensor. One of the wires was broken in the insulator at the neck of the crank sensor connector.

@alfredozertuche784

3 жыл бұрын

@@cedanecox5733 been having the same symptoms on my moms vehicle. i got it going after replacing the crank sensor now its doing the same. this is what i was thinking what the issue is. Wasnt a 100% sure it might be the wiring looks like im going to have to do some continuity test. thanks glad your issue was resolved. safe travels

@cedanecox5733

3 жыл бұрын

@@alfredozertuche784 I hope you get this resolved. The insulator was firmly fitted in the connector with the wiring broken so don't be fooled; give it a little pull and if it's broken it will be released easily.

@alfredozertuche784

3 жыл бұрын

@@cedanecox5733 thanks will be checking tomorrow. i knew it had something to do with the crank sensor but wasnt 100% sure thanks again for the reply

My mazda 3 2008 sedan z6 dnt want to start after l make a short

My Mazda CX9, 2012, some time the engine does not start on first or 2nd ignition. What should I check?

@dasonest

3 жыл бұрын

Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem?

@rachelr.n.3563

3 жыл бұрын

@@dasonest does it lag while trying to start..mine is doing that ..HELP!! No it has juice but won't start

@dasonest

3 жыл бұрын

@@rachelr.n.3563 i just used baking soda and hot water to clean the terminal of battery. Since then its starts no issues..

My Mazda doesn't have those Blue fuises

What if the P light indicator does not light up and it cranks but does not start. What should we do?

@vvv-jz9wx

2 жыл бұрын

Find a solution??

@arturbercan

10 ай бұрын

Put it in neutral...it should Start The shifter cable lever at the transmission is probably rusted/not moving properly causing shifter position misalignment

Hello i have mazda 6 2013 2.2 skyactive turbo diesel I have codes u0100 u0115 u0121 they are permanent the car cranks no start I put new battery checked all fuses and relays Cables and connecters but no use they keyless been checked and its good is there anyway u can help thank u 🙏

@lilsolo3602

7 күн бұрын

Hello I got the same problem

My mazda 3 2008, will start bu will turn off after a few minuts. After a few minuta it will come bac on, Any idias???

@gabrieldusk

3 жыл бұрын

Camshaft sensor.

Don't think my fuse box ever been opened till today

How do I reset how do I get to start

My starts and then shuts off,I was knocking a nut don’t know if knocking shut down fuel pump

@joseone69

4 жыл бұрын

thats the knock sensor shutting down the engine do to knocking , its sounds like you need a engine

@gawaynepinnock7037

4 жыл бұрын

Jose Torres thanks I figured it out the teeeth on the crank shaft was bent so the sensor was not send getting a correct reading that’s why car was not starting

@carmenjuarez2023

4 жыл бұрын

@@gawaynepinnock7037 its fuel pump replace compltely

@dasonest

3 жыл бұрын

@@joseone69 Same to my mazda 6 2009 it clicks first then second or third will start. What could be the problem? I cleaned the battery terminals and its 12.7v but stil clicks 1st second wil start or 3rd. Somes 1st starts. Any help?

My Mazda try to start but wont start like it not getting gas

1991 pickup trck 2200

Does itit work also on 98 323?

@myes344

4 жыл бұрын

Theres no 98 323

@daigonaticsgulapanatics2556

4 жыл бұрын

@@myes344 depends on your country. we had one.

@joseone69

4 жыл бұрын

@@myes344 yes there is is the protege here is link en.wikipedia.org/wiki/Mazda_Familia

Toyota is the best

Drinking game ....every time he says now....or guys

Hi. My mazda cx7 is hard starting when cold engine. When in hot weather, it start the engine easily. Anybody experience this problem? How to fix this?

@Petefenlon

2 жыл бұрын

Same issue here. Did you figure it out?

@jpcyclistangpinoy2989

2 жыл бұрын

@@Petefenlon did you guys get it fixed?

@Petefenlon

2 жыл бұрын

@@jpcyclistangpinoy2989 Yeah, it was a bad battery. I did the chris fix multimeter test and was dropping below 10V when cranking, suggesting that the battery was almost dead. Got a new battery and started it in -25 degrees this morning.

@jpcyclistangpinoy2989

2 жыл бұрын

@@Petefenlon I already change mine with a new battery it worked but again having the same problem after a week..too cold maybe. all fuses are good

@Petefenlon

2 жыл бұрын

@@jpcyclistangpinoy2989 Sounds like you've got some indepth troubleshooting ahead of you. Spark plugs and starter are what I'd check next, but I'm definitely not a professional...

The gage

Mazda duh why won't it start?

Let’s just all agree Mazda’s are badly made 🤦‍♂️

@FokwaDivine

2 жыл бұрын

True

@JA-gx4hb

Жыл бұрын

Scotty Kilmer loves them.

@kidthunder1311

Жыл бұрын

I loved my CX-9, had no major issues. I traded it in at 140,000 miles, because about half of them will have a massive INTERNAL water pump failure.

@LuvHawaii

Жыл бұрын

Wish I knew that before I bought it

@comically_largesponge

Жыл бұрын

@@kidthunder1311my mom has CX7 and major problem is all windows broken but driver window still fine Rear door left and right also broken

I know what's wrong with this car ....you let a woman near the engine with the hood open 😜😭😂

@nenabena9696

Жыл бұрын

hilarious

GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS,GUYS.Watch just to count how many times he says GUYS.Its a joke.

Had to stop watching, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS, GUYS Is all I heard!

@yolandamorua107

2 жыл бұрын

Check your hearing aid , maybe a bad connection.

@Thewarriorway534

2 жыл бұрын

You have a problem bro

@brendanmyrick9466

2 жыл бұрын

Or you could focus on what he had to say

@rudolfscholtz4810

8 ай бұрын

Should we rather subscribe to your channel?

poor video

I'm having er serious problem with your heavy accent, why not just make videos in your native language?

@reneerogers3646

4 жыл бұрын

I'm very happy they are making such helpful mazda videos! Regardless of accent :) they make videos other people in the US don't seem to!

@teemupeju2139

4 жыл бұрын

The accent is awesome 💪

@johnwatson2379

4 жыл бұрын

If anything, the accent makes me feel like his car expertise is more legit 💪

@joseone69

4 жыл бұрын

@@johnwatson2379 i'm a mechanic my self and i don't think anything wrong with his accent.

@rachelr.n.3563

3 жыл бұрын

That's rude, I understand him just fine!!

Guys guys guys guys and more guys guys guys because everybody is a man aka guy aka guys guys guys guys guys guys guys......