This is a really informative video

Hey man thank you so much brother honestly!! Step by step love it 😍 perfect how it was diagnose and explain and showed to us thank you again!

@johnandeddie

Жыл бұрын

Great to hear!

Best video on this issue. Thanks!

@johnandeddie

8 ай бұрын

You're welcome!

damnnnnnnn! that's some solid diagnosing!

I have a 2004 Mazda 3 2.0 have some of these some problems it don't have a tcm

Hi there, thanks for your video; that's really helpful. I had a similar problem. The AT light went on four times, and it happened three times while I was driving. The AT and engine lights just came on, but I didn't feel anything. The AT light disappeared when I pulled over and restarted the engine. I went to the workshop and got the codes P0758 twice and P0768 once saved in the computer. However, when the mechanic read the real data from the car, everything seemed normal. They checked the wiring in the hood (not sure which one😂), but they didn't check the wiring to the TCM because they would have to remove the battery, which would add more labor cost. They suggest that if the wiring connected to the TCM is normal, they will have to check the solenoid in the gearbox, but this will be very expensive. However, I think it's likely an issue with the TCM. I would appreciate your suggestion on this matter.

@tafadzwamakuvire8465

Жыл бұрын

have you won on this problem

@mikezhao5294

Жыл бұрын

@@tafadzwamakuvire8465 I bought a OBD scanner, and delete error code, and it doesnt back for 3 weeks so far. I think it more likely due to the TCM, and its the computer thing, not due to the bad solenoid.

Hi. Sorry about the long message but I would really appreciate your help because I don’t want to spend a lot of money on this if not necessary. I have a 2015 Mazda 3, it has about 69k miles. The issue we had originally was that when we would take it past like 20 mph the car would kind of jump like it was being forced to accelerate, it was almost like it was in neutral, or it had the emergency brake on and that later turned into the car not wanting to move at all. It would just kind of idle and I’d have to turn it off and back on again to get it to move.. We’ve tried changing the battery, we’ve changed the transmission fluid and none of those things really worked. We’ve taken it to a couple shops and everyone says it’s the transmission but we spoke to an individual mechanic and he doesn’t think it’s the transmission, he thinks it’s something electronic or maybe some thing with the shifter solenoid because when we switched it to manual it was driving more smoothly, it was just not consistently recognizing what gear it was in. Any advice?

@johnandeddie

9 ай бұрын

Scan for codes and watch data stream making sure everything external is ok. If so you may have a internal trans concern.

In my 2008 Mazda 3, the transmission connector splits off into two separate connectors. One looks just like the one in this video, but then 5 wires go off to a different connector. Should I unplug them both to test the circuit? I also don't have any yellow wire to test the computer. You wouldn't happen to know how to find a schematic or something that would tell me which wire goes to solenoid B, would you?

@johnandeddie

Жыл бұрын

Try unplugging and testing, Google wire diagram

@reneeshuey2593

Жыл бұрын

Thank you for your reply! I was able to find the wire with that diagram, and ultimately decided to just send the TCM off for repair. Put it back in two days ago and so far it seems to have solved the issue! Thanks so much for posting this diagnostic tutorial!! So glad it could be a $375 repair instead of the cost of replacing the solenoid.

@Minecraftgamers567

Жыл бұрын

@@reneeshuey2593solenoids are like $60 tho

Mazda 3 is more likely to have a faulty tcm than a pcm next fault is likely to be contaminated solenoids due to a lack of transmission oil changes .

Hi I have a 2010 Mazda 3 with 70k miles. I scanned the code and it only showed P0758. Seems to drive okay but has hard engagements. Do you think it can be the solenoid or tcm. I didn’t see a tcm code tho

@johnandeddie

2 жыл бұрын

Most common is tcm. The position the tcm sits in the vehicle allows to to much heat. We will relocate tcm to firewall to keep temp down on tcm

@coromantobass3788

2 жыл бұрын

@@johnandeddie yep it was, thanks

Is it possible to have an intermittent problem? My daughter’s car is and 08 Mazda 3 with this code. Did all the tests and everything was good. Had 2.6 ohms on first test, went o/l on second test and had 4.96 volts on last test. When I drive her car it works good for about 10 minutes and then it starts shifting hard and sets the code.

@johnandeddie

2 жыл бұрын

Yes most common failure is tcm

Hello ,I ll really be appreciated if u can answer my question ,cuz I really need a advise before I spend money ,I have 2010 mazda3 , it's araund 220k miles, 2 weeks ago AT light came out and car looks like doesn't go to 2nd or 3rd gear and It cant speed more than 35 miles an hour unfortunately, is it sounds like I need to change the transmission itself or something is fixeble some other way ? please help me with your advise , I do food delivery with this car as a second job and I need it couple more months before I change my car ,and I'm sorry for my English ,thank you and God bless you

@johnandeddie

Жыл бұрын

Have it diagnosed and scanned for trouble codes. Tcm are common and circuits are common failures

Is $1400 a good price for mazda 3 2008 that could have one or all bad wirehardness, solenoids,and tcm. The owner dad replaced the transmission and afterwards the issues in video is happening, it won't go out of 3rd gear. What would be a fair price? Would i need to check the whole wirehardness or just do what's in the video?

@johnandeddie

Жыл бұрын

Not a bad price for a vehicle that has a good running engine, trans, and decent body and tires. Start with ohming out circuits

at last solution to a problem!

I have a 2004 Mazda 3 sedan automatic transmission the other day it felt like transmission was slipping are shuddering the got to the point of not wanting to pull it was hitting hard to reverse and drive after hesitant to change gears now is stuck in I'm thinking 3rd gear don't know if worth putting much money into it because of its age has roughly 170,000. miles on it can't afford much money being on social security

@johnandeddie

Жыл бұрын

Have your vehicle diagnosed by a reputable shop. The least expensive alternative if it needs a transmission replacement, is a low mileage good used one.

I hate these fl and 4l Ford transmission, I have tried to fix them and the only real way is to do a complete overhaul which is expensive. My suggestion check your transmission plug connector, then check your shift selector below it to make sure it's not broke, then use Ford scan to check transmission pressure and lock up if solenoids go crazy then they are failing or losing pressure. Check your internal filter. The solenoids go bad, the valve bodies warp, the piston drum leak, the clutch packs burn up. The servo bore wears causing the 3-4 issue. The TCM fail. Good old ford garbage.

I have a 2004 mazda 3, my AT light came on the other day and it shifted down in 3rd gear and would only go into 1st and 3rd gear. It revs real high and shifts really hard especially putting it in reverse and drive. The 2004 have no tcm, I ordered a new ecm should that fix my problem? Or should I try to replace the transmission speed sensor too? Hope you get back to me thanks oh ya no codes are coming up on the code reader I have available.

@johnandeddie

2 жыл бұрын

If the AT light is on it should have a transmission code in the system. Otherwise your problem could be related to either the pcm or one of the speed sensors (not sure how many there are on that model). Don't rule out the possibility of an internal transmission issue as well. Let us know what you find out.

@Cornbreadfed420

2 жыл бұрын

@@johnandeddie thanks for the reply.. ya ordered a pcm , thinking about just getting the speed sensor on the trans also it's like 25$ way cheaper then the pcm 187$. Will do..

@ralphnapierii1184

2 жыл бұрын

@@Cornbreadfed420 how's it going?

@Cornbreadfed420

2 жыл бұрын

@@ralphnapierii1184 I still haven't figured it out..replaced the sensor with two prongs on top of the transmission with no luck. Dealing with family stuff so kinda have no time atm

Hello.. I have a Mazda 2007 It's gets stocks in when accelerating up to the 3rd or 4th gear . We diagnosed it an brought out the code number p0883.. Please why does it means..?

@johnandeddie

2 жыл бұрын

Circuit High Input codes like P0883 are mostly caused by defective alternators that develop excessive voltages, although there may be other ...

I have a Mazda 3 (HB) 2009 1.6L, today I was driving the vehicle and suddenly AT & Check Engine light came on. Gear stuck on 3, I reached home. Turned off my car then turned on shifted to D at this point gear Num was 1 I didn't move my car but gear went to 2nd within 2Sec. My car doesn't have a TCM. So what could be the cause. TF level is good, changed AT strainer a month ago. On OBD I received P0758, Shift Solenoid B Electrical. Cleared the code to reconfirm and it popped up again. Shift to R makes harder, upshifting from 2 to 3 not so hard but down shifting does. Pls help.

@johnandeddie

2 жыл бұрын

Possible solenoid, circuit or pcm/tcm

2 questions, 1) what does it mean when you let car sit a few hours and then there's no issues, everything rest? 2) does this video apply to mazda cx9 or only 3?

@johnandeddie

Жыл бұрын

Similar to CX9, Check power, signal, and ground circuits

Does anyone know the TCM location on a 2014 Mazda 2?

@JoeBananas77

Жыл бұрын

Under batter tray

So the first two tests had the same results yours did. However, when I tested the TCM, it showed a millisecond of 4.75 volts then dropped to 3.75 volts. Is this the problem then? You said it should be at 5.

@johnandeddie

Жыл бұрын

These vehicles are known for bad tcm"s

Po758 Mazda6 2003

My 2010 Mazda3 is throwing P0753 solenoid A. If I follow your procedures there, what spot on the tcm harness for I use to ohm out solenoid A to test it? I sent in my tcm to get repaired, got it back and it's still doing the same stuff if not worse, shifting harsh in drive/reverse and won't shift past third gear. So either my shift solenoid is actually bad, or they didn't fix the tcm properly

@johnandeddie

2 жыл бұрын

possible solenoid problem

@Pitviper1996

2 жыл бұрын

Connection issue I think. I used compressed air and blew out the connections to the tcm and the connection to the transmission and the issues went away for now... Weird

@Minecraftgamers567

Жыл бұрын

@@Pitviper1996did they ever come back?

@luisalbertovaldezayala390

8 ай бұрын

​@@johnandeddieI moved solenoid C to solenoid A and vice versa, car stills throwing P0753 shift solenoid A.. was that enough to test that the soleniod is not the issue?

Hey, I have a 2007 Mazda 3 2.3L and was getting code P0758. It had hard shifting when moving the gears through park reverse and drive and something was smoking. A friend who’s a mechanic said it’s 98% my TCM. So I put a brand new one in and now I’m getting P0757. P0758 isn’t there anymore, and the shifting isn’t as rough when cycling through the gears in park. The RPM’s go to about 4500 when changing from 2,3,4 and lost any acceleration in 4th gear while driving like it was in neutral. P0757 & 8 both are solenoid B codes do you think my TCM was fine and I have another problem or what do you think is going on?

@johnandeddie

Жыл бұрын

Check circuit from tcm to solenoid b

@garyshay6674

Жыл бұрын

Have you received a response? Have you diagnosed the problem? tia

HI THERE ! When i ohm out on my 2010 mazda 5 i get 13 ohms ? does that mean it's bad ?

@johnandeddie

2 жыл бұрын

Should be ok, you can apply 12 volts and click solenoid to confirm

Hi bro u hav a phone nombre for those people dat repair those tcm

@johnandeddie

9 ай бұрын

We use a number of different supplies depending on availability, try Flagship One thx for watching

how do i get my car to you... lol good mechanics are so hard to find. lol I will fly you out to california

***THIS COMMENT IS FOR USERS WHO HAVE 2007 MAZDA 3 2.0L*** THE TCM IS INTEGRATED INTO ECM AND IS NOT BOLTED UNDER BATTERY HOUSING, I COULDN'T FIND THE DAMN THING AND THIS IS BECAUSE ITS NOT THERE. WHAT PEOPLE DO IN MY SITUATION...IM STILL WORKING ON IT...

@johnandeddie

2 жыл бұрын

Location vary, should be engine compartment or under dash

Are you ready for another challenger? I have a 2006 Mazda3 with 5 speed AT, which only stays on 4th gear w/o any OBD code. Put on a rebuilt TCM and brand-new OEM TCM; ain't fix nothing!

@johnandeddie

Жыл бұрын

Most likely solenoids and/or circuits