My Maytag washing machine has loudly noise when draining, I searched many videos until I find yours. I find a piece of sheet metal in my drain pipe near pump, you saved my day. I almost give up to buy a new one 😂

Thank you for this video. What I thought would be an expensive repair or replacement, turned out to be a 30 minute self fix! Couldn't have done it without this video!

@ToddsGarage

3 жыл бұрын

Thanks for watching, glad the video helped!

like many others here.. I am very appreciative you took the time to make this video.. the wife and i were fixing to buy a new machine thinking our motor was going bad with the rattling noise.. come to find out it was a zipper very similar to what you pulled out of your.. thank you thank you thank you

Thank you! I have a different model Maytag washer but this video helped me tremendously. I’d unintentionally washed work pants that had several rivet stems in one of the pockets. When the washer drained, it sounded like a bunch of coins being tossed around…similar to a slot machine. As soon as I pulled the hose off, I found the problem. I did take another reviewers advice. I removed the pump and shorter hose and cleaned them as well, since I already had it apart.

Thank you!!! This was my exact problem. Had a small nail at the end of the drain pump. First time fixing a washer and happy to say it was a success!

Thank you so much! Had that same sound you described and followed your instructions. Found a sock stuck in the pump! Saved a bunch of money on the repair man.

@ToddsGarage

2 жыл бұрын

Thanks for watching, and I am glad this video helped!

I have the exact washing machine and went under it from the front instead of the rear. I could hear and feel my pump running, but nothing was draining. I was able to remove the black rubber pump inlet house and found a bunch of gunk, hair and bobby pins that were stuck at the outlet of the tub. By using one of those small plastic drain snakes with lots of barbs, I cleared the tub exit. I think I'm back in business. Thanks for the video and getting me headed in the direction of the tub to pump to drain circuit that ended up being clogged.

@ToddsGarage

3 жыл бұрын

Thanks for watching, glad the video helped and glad you got yours fixed!

Great video. One thing might make your job a little easier as far as making sure there is nothing else in the pump, the white part of the pump exterior is a cover for the prop. It comes off with two or three screws (yours is three I think) but if you remove that you can inspect the fan as well as the seals without trying to feel it with the fingers. It will also help if you have something smaller stuck in the pum as often times little nails or whatever will wedge themselves underneath the blade. Cool stuff tho

Thank you!!!! I found a finishing nail in mine

I have the same washer and it is not completely draining and it make a strange sound. I will be trying this today I think I might have the same issue. Thank you for your video.

@ToddsGarage

3 жыл бұрын

Thanks for watching, hope you figured it out!

Glad i found this video, I can feel the plastic fan like pieces inside the pump , they seem jammed to me, are they suppose to spin all the way wondering if there could be something lodge on the farther side that i can't reach, the sound was so loud like a 8 second startling buzzing screetch rattle , and it didn't drain the clothes all the way, had to ring out by hand good thing it was just little baby girl clothes. It started doing this when i tried to use the hand wash cycle.

@ToddsGarage

3 жыл бұрын

Thanks for watching hope you get it figured out.

love the pac-man pajamas

@ToddsGarage

2 жыл бұрын

Thanks for watching, they are one of my favorite pairs of pjs. I have some arcade videos in my channel you might like!

THX for this video👏...it is a helpful video...My washer is exactly like yours...My problem is that more hot water comes out than cold or warm temperature water. I HAD A FRIEND HOOK IT UP AFTER PURCHASING IT... PLEASE HELP🙏

@ToddsGarage

2 жыл бұрын

Thanks for watching. I am not sure what that could be, sorry I cant be of more help. I hope you are able to get it fixed.

Good video. Any ideas on this washer being loud and unsteady during spin cycle?

@ToddsGarage

3 жыл бұрын

Hi not sure what that could be, mine will do that sometimes when the load isn't balanced inside. Good luck hope you figure it out.

I have this exact machine it won't agitate just makes a clicking sound but it still spins. Any suggestions?

I've got that same one, but my problem has been that wits shaking bad when in the spin cycle...the whole washer violently moves. We replaced the shock absorbers and such, but that didn't work. Any advice?

@stormisporn

Жыл бұрын

If you go inside the the washer itself you can take off the washer blade by twisting the middle nob inside. After the knob is off use a socket to unscrew the hex head. Once that’s off check around and see if their is anything that shouldn’t be there

Important info (from Maytag's website): If no water is detected entering washer after 13 minutes, the washer will go into a drain routine. When the washer goes into a drain routine, it will sound like it's draining for approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time. Please wait 10 minutes before trying to perform any functions. I just took the damn thing apart for no reason (it was a royal pain in the az because of tight quarters). I thought I had forgot to take an Allen key out of my pocket, along with a tiny hex nut on the end. I rushed over to the machine after it already filled+started washing, and started removing my soaking wet clothes from the washer, hoping to locate the Allen wrench+hex nut. I got the whole thing apart+put back together. Soon after I was done I thought to check on my car's passenger seat for the wrench+nut and they were there. I looked everywhere except the car. The moral of the story is that if you start removing clothes after the machine already filled up with water, it's going to go to the 10 minute long auto drain cycle. Because it kept draining after all the water in the tub was gone, I thought something was stuck in the pump (like in this video). What a 💩 sandwich.

@ToddsGarage

3 жыл бұрын

That is s rough story! Thanks for watching though!

I have the same one, it clicks when the washer is slowing down. Quite annoying, could it be the same issue?

@ToddsGarage

3 жыл бұрын

Hi, hard to say for sure, sorry I can't be of more help. Hope you get it figured out!

Thank you. How long do these pumps usually last?

@ToddsGarage

3 жыл бұрын

Hey Steve, not sure, when I was looking up the part in case I had to replace mine it was about $50 fyi. Thnaks for watching!

My drain pump makes noise when it's filling and water doesnt come in.

I ha e same machine n is leaking can't find where is coming from

I had a similar issue, I took off the back panel , I took off the agitator , turns out what I had to do was have someone help turn the unit so the bottom can be accessed , and around motor there is a protective plastic housing, that one piece broke off and pointed up to the fly wheel creating a clicking sound, I just bent it back and the problem was solved . Hope that can help someone

lol, found my wife’s panyhose, thanks for the video.

Mine sounds like an airplane taking off when it spins. It's awful.

😁

@ToddsGarage

3 жыл бұрын

Thanks for watching!

maybe a magnet would help you

Union made junk! My Maytag dryer broke within a year. My Maytag washer barely lasted five years. When I was a child we had one washer and dryer that lasted my entire childhood. American products (especially union made) are extremely unreliable. Time to but Samsung or LG.

@TADDs101

3 жыл бұрын

Samsung appliances are JUNK to

@johnthomas1178

3 жыл бұрын

@@TADDs101 I bought an LG. Fingers crossed. 🙂

@TADDs101

3 жыл бұрын

Just worked on my 16yr old Maytag washer today, it was making a squealing sound during the spin cycle .. found it was the water pump. Fixed and runs quiet now

@hoodmeister

3 жыл бұрын

Union workers just assemble them. The problem in this video and the problems I had were all design or user error related. They're engineered to be cheap to make and easy to manufacture. Can't blame the unions for that.

@cindyjohnson5242

2 жыл бұрын

@@TADDs101 thanks ! Do you have a link how to do it? I have a 27 year old one.