Another thing i thought of that will make great use with these is the twist off sockets for rounded nuts/bolts then you probably wont even need to hammer the twist off socket on to the fastener

Go to “Eric the Car Guy video, “ Kryptonite on Stubborn Screws, The Shake N Break” to see the tool work and get an unbiased opinion oh how it works. Has many more uses then brake rotor screws!

Would only work on a shouldered bolt.

Put the tape over the socket so it'll push the tape in and hold better.

Yea handheld impact driver is better for small bits. Air hammer might be to powerful & break bits Just Sayn 😁

Or buy the Wivco versions, they have retaining rings similar to what’s on your impact gun.

Put a tiny weld on it and grind down to desired fit

Snap ring retainer.

Does this damage the combo wrench used? Especially if used often?

@OnTheWorkbench

2 жыл бұрын

I've only used this a couple of times and never with a "good" wrench for just that reason.

@behelpful1435

2 жыл бұрын

@@OnTheWorkbench I'm just worried the wrench would explode or something... Similar to if one used a non-impact socket on an impact gun, how that socket can explode.

Why not just use an air or battery impact wrench?

@gerardjones7881

Жыл бұрын

thats a good way to twist the head off seized screws and rusted bolts.

@nbpt1000

10 ай бұрын

The conventional method is to use heat. It almost always work but sometimes you can not use a torch. Like near plastic or rubber that will melt. Or near gas which is just dangerous. I fail to see a lot of benefit in this tool but I am sure it is better than nothing.@@gerardjones7881

I have this tool and it will destroy your impact sockets I have destroyed some of my snap on impacts they're rough on sockets!!

@connor3288

Жыл бұрын

Harbor freight baby! Lifetime warranty haha

Maybe you could tell us why you go to all of this bother when you could just use an impact driver... or show us why this is better!

@connor3288

Жыл бұрын

Your hand and a hammer vs an air hammer's 10,000+ pounds of force... Some are over 20,000

I don't get why you would use this with *an impact socket on an air hammer*, instead of just using *an impact socket with an air impact driver*. Seems like using an air hammer would be much rougher on your sockets as well as on the fastener itself. Note: For those that never did quite master the skill of READING before POSTING, please note that I am NOT questioning whether one should be using an impact socket versus a non-impact socket. Keep this in mind and READ before making yourself look like a total moron by replying with irrelevant comments.

@TaintedMojo

3 жыл бұрын

I strongly recommend not using a chrome socket with this tool unless you want to dig steel splinters out of your carcass

@StilettoSniper

3 жыл бұрын

@@TaintedMojo And I would strongly recommend you spend more time reading comments thoroughly before posting an irrelevant response fresh out of your own carcass. Perhaps then you might notice I said NOTHING about using a chrome hand tool socket.

@TaintedMojo

3 жыл бұрын

I’m not the one asking in incredibly stupid questions

@duckhunter8203

Жыл бұрын

@@StilettoSniper Wow are you always this friendly? Bet you have plenty of people queuing up round the block wanting to be mates with you......Not!!

@connor3288

Жыл бұрын

Why you would use this? Because you are dealing with a rusty bolt/nut/screw that is stuck and will break if you try to undo normally. Like small diameter stuff, rotor/torx screws, bleeder screws, etc

Useless video doesn't show how it works...

@nbpt1000

10 ай бұрын

I would not go as far and say use less. But it is limited to bringing it to peoples attention and a few ideas on accessories.